Practical Experiences of Improvement of Oil Recovery for SZ Heavy Oil Reservoir in the Stage of High Water-cut

Author(s):  
Yanchun Su ◽  
Liu Yingxian ◽  
Yanlai Li
2012 ◽  
Vol 616-618 ◽  
pp. 992-995
Author(s):  
An Zhu Xu ◽  
Long Xin Mu ◽  
Xiang Hong Wu ◽  
Zi Fei Fan ◽  
Lun Zhao

The dryness of superheated steam is 100% and it exists in the form of pure steam whose properties are like ideal gas. When the steam has a large degree of superheat, it may take a relatively long time to cool, during which time the steam is releasing very little energy and transmitted long distances. The heating radius of superheated steam in the formation is 5-10m larger than saturated steam. In the heating area of superheated steam, the comprehensive effects by superheated steam (crude oil viscosity reduction, improved flow environment, changes in rock wettability and improved oil displacement efficiency, etc.) is much higher than that of saturated steam. Superheated steam stimulation in Kenkyak high water cut heavy oil reservoir pilot test results showed that the average daily oil production of single well by superheated steam stimulation was 2-4 times than that of saturated steam stimulation. Superheated steam is more effective to heat water-invaded oil reservoir than saturated steam.


2007 ◽  
Vol 22 (01) ◽  
pp. 46-49
Author(s):  
Hong'en Dou ◽  
Yu wen Chang ◽  
Dandan Hu ◽  
Wenxin Cai ◽  
Guozhen Zhao

2016 ◽  
Author(s):  
Al Shibli Abdullah ◽  
Al Hinai Suleiman ◽  
Belghache Abdesslam ◽  
Al Habsi Sumaiya

2021 ◽  
Vol 329 ◽  
pp. 01047
Author(s):  
Qingting Wei ◽  
Guinan Zhen ◽  
Weilong Wang ◽  
Jiamin Qin ◽  
Hongcheng Luo ◽  
...  

The recovery ratio is an important indicator to evaluate the effectiveness and performance of oilfield development. In order to clarify the key factors of oilfield recovery ratio in the stage of super-high water cut, 9 dynamic indicators of 12 blocks are analyzed in heavy oil reservoir of eastern China in application of reservoir engineering principles and statistical analysis methods. The results show that the four key factors of recovery are the well density, the ratio of producing wells and injecting wells, net cumulative injecting rate and the bottom hole flow pressure, and the weight of each indicator is quantified. In the horizontal contrast, comprehensive forecasting target recovery is compared with the current recovery by the dynamic method to determine according to typical block BXD. Four of important factors are discussed for the previous trend and the countermeasures of according adjustment are put forward. The proposed method and the results have a certain reference value of the theoretical research and practical application in the stage of super-high water cut oil-field.


2021 ◽  
Author(s):  
Yong Yang ◽  
Xiaodong Li ◽  
Changwei Sun ◽  
Yuanzhi Liu ◽  
Renkai Jiang ◽  
...  

Abstract The problem of water production in carbonate reservoir is always a worldwide problem; meanwhile, in heavy oil reservoir with bottom water, rapid water breakthrough or high water cut is the development feature of this kind of reservoir; the problem of high water production in infill wells in old reservoir area is very common. Each of these three kinds of problems is difficult to be tackled for oilfield developers. When these three kinds of problems occur in a well, the difficulty of water shutoff can be imagined. Excessive water production will not only reduce the oil rate of wells, but also increase the cost of water treatment, and even lead to well shut in. Therefore, how to solve the problem of produced water from infill wells in old area of heavy oil reservoir with bottom water in carbonate rock will be the focus of this paper. This paper elaborates the application of continuous pack-off particles with ICD screen (CPI) technology in infill wells newly put into production in brown field of Liuhua, South China Sea. Liuhua oilfield is a biohermal limestone heavy oil reservoir with strong bottom water. At present, the recovery is only 11%, and the comprehensive water cut is as high as 96%. Excessive water production greatly reduces the hydrocarbon production of the oil well, which makes the production of the oilfield decrease rapidly. In order to delay the decline of oil production, Liuhua oilfield has adopted the mainstream water shutoff technology, including chemical and mechanical water shutoff methods. The application results show that the adaptability of mainstream water shutoff technology in Liuhua oilfield needs to be improved. Although CPI has achieved good water shutoff effect in the development and old wells in block 3 of Liuhua oilfield, there is no application case in the old area of Liuhua oilfield which has been developed for decades, so the application effect is still unclear. At present, the average water cut of new infill wells in the old area reaches 80% when commissioned and rises rapidly to more than 90% one month later. Considering that there is more remaining oil distribution in the old area of Liuhua oilfield and the obvious effect of CPI in block 3, it is decided to apply CPI in infill well X of old area for well completion. CPI is based on the ICD screen radial high-speed fluid containment and pack-off particles in the wellbore annulus to prevent fluid channeling axially, thus achieving well bore water shutoff and oil enhancement. As for the application in fractured reef limestone reservoir, the CPI not only has the function of wellbore water shutoff, but also fills the continuous pack-off particles into the natural fractures in the formation, so as to achieve dual water shutoff in wellbore and fractures, and further enhance the effect of water shutoff and oil enhancement. The target well X is located in the old area of Liuhua oilfield, which is a new infill well in the old area. This target well with three kinds of water problems has great risk of rapid water breakthrough. Since 2010, 7 infill wells have been put into operation in this area, and the water cut after commissioning is 68.5%~92.6%. The average water cut is 85.11% and the average oil rate is 930.92 BPD. After CPI completion in well X, the water cut is only 26% (1/3 of offset wells) and the oil rate is 1300BPD (39.6% higher than that of offset wells). The target well has achieved remarkable effect of reducing water and increasing oil. In addition, in the actual construction process, a total of 47.4m3 particles were pumped into the well, which is equivalent to 2.3 times of the theoretical volume of the annulus between the screen and the borehole wall. Among them, 20m3 continuous pack-off particles entered the annulus, and 27.4m3 continuous pack-off particles entered the natural fractures in the formation. Through the analysis of CPI completed wells in Liuhua oilfield, it is found out that the overfilling quantity is positively correlated to the effect of water shutoff and oil enhancement.


2021 ◽  
Author(s):  
Xiang Zhou ◽  
Yongsheng Tan ◽  
Qi Jiang

<p>In this study, in order to enhance heavy oil recovery in the heavy oil reservoir with a high-water-cut after water flooding process, experimental and numerical simulation studies are conducted. In the experimental studies, firstly, the properties of the heavy oil-CO2 system were measured under different saturation pressures at the reservoir temperature. Secondly, to mimic the high-water-cut condition in the real reservoir, water flooding process was conducted for each core; then four long core experiments insist of one CO2 huff `n` puff process and three CO2 flooding processes were implemented. The CO2 huff `n` puff process is conducted to compare the production performance with that in the CO2 flooding process to optimize the method. Regarding the CO2 flooding process, different gas (pure CO2, flue gas) and different production categories (constant production pressure, pressure depletion) were applied to study the heavy oil production performance in the heavy oil reservoir with high-water-cut. The experimental results indicate that, the CO2 flooding coupling with pressure depletion process is the best choice to reduce the water-cut and enhance the heavy oil recovery, which is 41.84% of the original oil in place and the water-cut reduced to lower than 70%. In the numerical simulation studies, the WinProp module in CMG is applied to simulate the properties of the heavy oil-CO2 system, which is generated by recombining CO2 into heavy oil, and high agreement simulation results were obtained. Then the results of the optimized experiment were history matched using GEM module. Finally, the upscaling studied was conducted. The CO2 flooding processes are carried out in the studied reservoir to maximum the heavy oil recovery factor. Moreover, the CO2 storage ratio is studied using GEM model.</p>


2009 ◽  
Author(s):  
Daniel Daparo ◽  
Luis Soliz ◽  
Eduardo Roberto Perez ◽  
Carlos Iver Vidal Saravia ◽  
Philip Duke Nguyen ◽  
...  

2021 ◽  
Vol 888 ◽  
pp. 111-117
Author(s):  
Yi Zhao ◽  
De Yin Zhao ◽  
Rong Qiang Zhong ◽  
Li Rong Yao ◽  
Ke Ke Li

With the continuous exploitation of most reservoirs in China, the proportion of heavy oil reservoirs increases, and the development difficulty is greater than that of conventional reservoirs. In view of the important subject of how to improve the recovery factor of heavy oil reservoir, the thermal recovery technology (hot water flooding, steam flooding, steam assisted gravity drainage SAGD and steam huff and puff) and cold recovery technology (chemical flooding, electromagnetic wave physical flooding and microbial flooding) used in the development of heavy oil reservoir are summarized. The principle of action is analyzed, and the main problems restricting heavy oil recovery are analyzed The main technologies of heavy oil recovery are introduced from the aspects of cold recovery and hot recovery. Based on the study of a large number of literatures, and according to the development trend of heavy oil development, suggestions and prospects for the future development direction are put forward.


Sign in / Sign up

Export Citation Format

Share Document