scholarly journals Application of Smoothed Particle Hydrodynamics (SPH) for the Simulation of Flow-like Landslides on 3D Terrains

2022 ◽  
Author(s):  
Binghui Cui ◽  
Liaojun Zhang
Keyword(s):  
Risk Assessment ◽  
Smoothed Particle Hydrodynamics ◽  
Disaster Mitigation ◽  
Sph Method ◽  
Landslide Event ◽  
Particle Hydrodynamics ◽  
Smoothed Particle ◽  
Simulation Results ◽  
Mitigation Design ◽  
The Impact

Abstract Flow-type landslide is one type of landslide that generally exhibits characteristics of high flow velocities, long jump distances, and poor predictability. Simulation of it facilitates propagation analysis and provides solutions for risk assessment and mitigation design. The smoothed particle hydrodynamics (SPH) method has been successfully applied to the simulation of two-dimensional (2D) and three-dimensional (3D) flow-like landslides. However, the influence of boundary resistance on the whole process of landslide failure is rarely discussed. In this study, a boundary algorithm considering the friction is proposed, and integrated into the boundary condition of the SPH method, and its accuracy is verified. Moreover, the Navier-Stokes equation combined with the non-Newtonian fluid rheology model was utilized to solve the dynamic behavior of the flow-like landslide. To verify its performance, the Shuicheng landslide event, which occurred in Guizhou, China, was taken as a case study. In the 2D simulation, a sensitivity analysis was conducted, and the results showed that the shearing strength parameters have more influence on the computation accuracy in comparison with the coefficient of viscosity. Afterwards, the dynamic characteristics of the landslide, such as the velocity and the impact area, were analyzed in the 3D simulation. The simulation results are in good agreement with the field investigations. The simulation results demonstrate that the SPH method performs well in reproducing the landslide process, and facilitates the analysis of landslide characteristics as well as the affected areas, which provides a scientific basis for conducting the risk assessment and disaster mitigation design.

scholarly journals Numerical Simulation of Non-Homogeneous Viscous Debris-Flows Based on the Smoothed Particle Hydrodynamics (SPH) Method

Water ◽  
2019 ◽  
Vol 11 (11) ◽  
pp. 2314 ◽  
Author(s):  
Shu Wang ◽  
Anping Shu ◽  
Matteo Rubinato ◽  
Mengyao Wang ◽  
Jiping Qin
Keyword(s):  
Debris Flow ◽  
Water Content ◽  
Smoothed Particle Hydrodynamics ◽  
Debris Flows ◽  
Sph Method ◽  
Particle Hydrodynamics ◽  
Sph Model ◽  
Smoothed Particle ◽  
The Impact ◽  
Kinetic And Potential Energies

Non-homogeneous viscous debris flows are characterized by high density, impact force and destructiveness, and the complexity of the materials they are made of. This has always made these flows challenging to simulate numerically, and to reproduce experimentally debris flow processes. In this study, the formation-movement process of non-homogeneous debris flow under three different soil configurations was simulated numerically by modifying the formulation of collision, friction, and yield stresses for the existing Smoothed Particle Hydrodynamics (SPH) method. The results obtained by applying this modification to the SPH model clearly demonstrated that the configuration where fine and coarse particles are fully mixed, with no specific layering, produces more fluctuations and instability of the debris flow. The kinetic and potential energies of the fluctuating particles calculated for each scenario have been shown to be affected by the water content by focusing on small local areas. Therefore, this study provides a better understanding and new insights regarding intermittent debris flows, and explains the impact of the water content on their formation and movement processes.

scholarly journals Numerical Simulation of Impact Behavior of Ceramic Coatings Using Smoothed Particle Hydrodynamics Method

2020 ◽  
pp. 1-25
Author(s):  
Jian Zhang ◽  
Zhe Lu ◽  
Sugrim Sagar ◽  
Hyunhee Choi ◽  
Heesung Park ◽  
...  
Keyword(s):  
Spherical Particle ◽  
Smoothed Particle Hydrodynamics ◽  
Coating Layer ◽  
Ceramic Coatings ◽  
Impact Angle ◽  
Impact Behavior ◽  
Sph Method ◽  
Particle Hydrodynamics ◽  
Smoothed Particle ◽  
The Impact

Abstract In this work, the impact behavior of an alumina spherical particle on alumina coating is modeled using the smoothed particle hydrodynamics (SPH) method. The effects of impact angle (0°, 30°, and 60°) and velocity (100 m/s, 200 m/s, and 300 m/s) on the morphology changes of the impact pit and impacting particle, and their associated stress and energy are investigated. The results show that the combination of impact angle of 0° and velocity of 300 m/s produces the highest penetration depth and largest stress and deformation in the coating layer, while the combination of 100 m/s & 60° causes the minimum damage to the coating layer. This is because the penetration depth is determined by the vertical velocity component difference between the impacting particle and the coating layer, but irrelevant to the horizontal component. The total energy of the coating layer increases with the time, while the internal energy increases with the time after some peak values, which is due to energy transmission from the spherical particle to the coating layer and the stress shock waves. The energy transmission from impacting particle to coating layer increases with the increasing particle velocity, and decreases with the increasing inclined angle. The simulated impact pit morphology is qualitatively similar to the experimental observation. This work demonstrates that the SPH method is useful to analyze the impact behavior of ceramic coatings.

scholarly journals Pressure evaluation during dam break using weakly compressible SPH

2019 ◽  
Vol 213 ◽  
pp. 02030
Author(s):  
Petr Jančík ◽  
Tomáš Hyhlík
Keyword(s):  
Experimental Data ◽  
Smoothed Particle Hydrodynamics ◽  
Two Dimensions ◽  
Dam Break ◽  
Kinematics And Dynamics ◽  
Sph Method ◽  
Weakly Compressible ◽  
Particle Hydrodynamics ◽  
Smoothed Particle ◽  
The Impact

This paper presents a solution of a dam break problem in two dimensions obtained with smoothed particle hydrodynamics (SPH) method. The main focus is on pressure evaluation during the impact on the wall. The used numerical method and the way of pressure evaluation are described in detail. The numerical results of the kinematics and dynamics of the flow are compared with experimental data from the literature. The abilities and limitations of the used methods are discussed.

The Theories and Application of Numerical Simulation with Smoothed Particle Hydrodynamics Method

2012 ◽  
Vol 531-532 ◽  
pp. 695-698
Author(s):  
Hui Lin Zhou ◽  
Hui Yong Yu ◽  
Ming Hua Pang
Keyword(s):  
Smoothed Particle Hydrodynamics ◽  
Three Dimensional ◽  
Hypervelocity Impact ◽  
Particle Model ◽  
Sph Method ◽  
Particle Hydrodynamics ◽  
Smoothed Particle ◽  
Impact Problems ◽  
Numerical Calculation Method ◽  
The Impact

The Smoothed Particle Hydrodynamics (SPH) method is a very important method to resolve hypervelocity problems and the basic theory of SPH method is introduced here. Then the three dimensional hypervelocity impact problems are simulated by using the model of chair. The results of SPH analysis show that (SPH) method is a numerical calculation method to resolve hypervelocity problems without mesh model but the particle model must be getting to calculate and the program code is less than other method. By analysis the results of the simulation is reasonable and very similar to the test result. It can be concluded that the advantages of SPH demonstrated make it a good and an ideal method to simulate the impact problem and other problems.

Smoothed Particle Hydrodynamics Simulations for Ultrasonic Machining of Different Workpiece Materials

2014 ◽  
Vol 1017 ◽  
pp. 758-763
Author(s):  
Jing Si Wang ◽  
Keita Shimada ◽  
Masayoshi Mizutani ◽  
Tunemoto Kuriyagawa
Keyword(s):  
Smoothed Particle Hydrodynamics ◽  
Material Removal ◽  
Fracture Behavior ◽  
Ultrasonic Machining ◽  
Machining Performance ◽  
Sph Method ◽  
Particle Hydrodynamics ◽  
Hard And Brittle Materials ◽  
Smoothed Particle ◽  
Simulation Results

The material removal in ultrasonic machining (USM) is based on brittle fracturing of workpiece materials. The properties and fracture behavior are different for varied materials, and they would have an influence on the machining performance of USM. The smoothed particle hydrodynamics (SPH) method was used to simulate the USM process for different workpiece materials. Three typical hard and brittle materials, i.e. silicon carbide (SiC), alumina (Al2O3), and glass will be used as the workpiece materials. Experiments are also conducted for comparing with the simulation results. Through this study, the material fracturing processes for different work materials are shown visually using the SPH method, which is very useful for USM study.

scholarly journals Progress in the Smoothed Particle Hydrodynamics Method to Simulate and Post-process Numerical Simulations of Annular Airblast Atomizers

2020 ◽  
Vol 105 (4) ◽  
pp. 1119-1147
Author(s):  
G. Chaussonnet ◽  
T. Dauch ◽  
M. Keller ◽  
M. Okraschevski ◽  
C. Ates ◽  
...  
Keyword(s):  
Smoothed Particle Hydrodynamics ◽  
Flux Ratio ◽  
Liquid Sheet ◽  
Sph Method ◽  
Post Process ◽  
Finite Time Lyapunov Exponent ◽  
Fragmentation Spectrum ◽  
Particle Hydrodynamics ◽  
Primary Breakup ◽  
Smoothed Particle

AbstractThis paper illustrates recent progresses in the development of the smoothed particle hydrodynamics (SPH) method to simulate and post-process liquid spray generation. The simulation of a generic annular airblast atomizer is presented, in which a liquid sheet is fragmented by two concentric counter swirling air streams. The accent is put on how the SPH method can bridge the gap between the CAD geometry of a nozzle and its characterization, in terms of spray characteristics and dynamics. In addition, the Lagrangian nature of the SPH method allows to extract additional data to give further insight in the spraying process. First, the sequential breakup events can be tracked from one large liquid blob to very fine stable droplets. This is herein called the tree of fragmentation. From this tree of fragmentation, abstract quantities can be drawn such as the breakup activity and the fragmentation spectrum. Second, the Lagrangian coherent structures in the turbulent flow can be determined easily with the finite-time Lyapunov exponent (FTLE). The extraction of the FTLE is particularly feasible in the SPH framework. Finally, it is pointed out that there is no universal and ultimate non-dimensional number that can characterize airblast primary breakup. Depending on the field of interest, a non-dimensional number (e.g. Weber number) might be more appropriate than another one (e.g. momentum flux ratio) to characterize the regime, and vice versa.

Modeling Hypervelocity Impacts Using Smoothed Particle Hydrodynamics

2018 ◽  
Author(s):  
M. Ganser ◽  
B. van der Linden ◽  
C. G. Giannopapa
Keyword(s):  
Smoothed Particle Hydrodynamics ◽  
Large Deformations ◽  
Hypervelocity Impact ◽  
Density Fluctuations ◽  
Computational Domain ◽  
Simulation Tool ◽  
Hypervelocity Impacts ◽  
Particle Hydrodynamics ◽  
Smoothed Particle ◽  
The Impact

Hypervelocity impacts occur in outer space where debris and micrometeorites with a velocity of 2 km/s endanger spacecraft and satellites. A proper shield design, e.g. a laminated structure, is necessary to increase the protection capabilities. High velocities result in massive damages. The resulting large deformations can hardly be tackled with mesh based discretization methods. Smoothed Particle Hydrodynamics (SPH), a Lagrangian meshless scheme, can resolve large topological changes whereas it still follows the continuous formulation. Derived by variational principles, SPH is able to capture large density fluctuations associated with hypervelocity impacts correctly. Although the impact region is locally limited, a much bigger domain has to be discretized because of strong outgoing pressure waves. A truncation of the computational domain is preferable to save computational power, but this leads to artificial reflections which influence the real physics. In this paper, hypervelocity impact (HVI) is modelled by means of basic conservation assumptions leading to the Euler equations of fluid dynamics accompanied by the Mie-Grueneisen equation of state. The newly developed simulation tool SPHlab presented in this work utilizes the discretization method smoothed particle hydrodynamics (SPH) to capture large deformations. The model is validated through a number of test cases. Different approaches are presented for non-reflecting boundaries in order to tackle artificial reflections on a computational truncated domain. To simulate an HVI, the leading continuous equations are derived and the simulation tool SPHlab is developed. The method of characteristics allows to define proper boundary fluxes by removing the inwards travelling information. One- and two-dimensional model problems are examined which show excellent absorption behaviour. An hypervelocity impact into a laminated shield is simulated and analysed and a simple damage model is introduced to model a spallation failure mode.

Smoothed Particle Hydrodynamics into the Fluid Dynamics of Classical Problems

2016 ◽  
Vol 846 ◽  
pp. 73-78 ◽  
Author(s):  
Maziar Gholami Korzani ◽  
S. Galindo Torres ◽  
Alexander Scheuermann ◽  
David J. Williams
Keyword(s):  
Fluid Dynamics ◽  
Analytical Solutions ◽  
Poiseuille Flow ◽  
Smoothed Particle Hydrodynamics ◽  
Slip Boundary Condition ◽  
Sph Method ◽  
Slip Boundary ◽  
Particle Hydrodynamics ◽  
Smoothed Particle ◽  
Computational Fluid Dynamics Cfd

The study concerns the application of the Smoothed Particle Hydrodynamics (SPH) method within the computational fluid dynamics (CFD). In the present study, some classical problems – the Poiseuille flow, the Hagen-Poiseuille flow, and the Couette flow – with the analytical solutions were investigated to verify a newly developed code of SPH. The code used for solving these problems, is an entirely parallel SPH solver in 3D and has been developed by the authors. Fluid was modelled as a viscous liquid with weak compressibility. The boundary walls were simulated with a special set of fixed boundary particles, and no-slip boundary condition was considered. Computational results were compared to available analytical solutions for transient hydraulic processes. Good agreement is achieved for the whole transient stage of the considered problems until steady state is reached. The results of this study highlight the potential of SPH to tackle a broad range of problems in fluid mechanics.

A STABLE LARGE DEFORMATION CORRECTED SPH METHOD BASED ON STABILIZED CONFORMING NODAL INTEGRATION AND LAGRANGIAN KERNELS

2012 ◽  
Vol 09 (04) ◽  
pp. 1250057
Author(s):  
S. WANG
Keyword(s):  
Large Deformation ◽  
Smoothed Particle Hydrodynamics ◽  
Solid Mechanics ◽  
Particle Methods ◽  
Sph Method ◽  
Nodal Integration ◽  
Particle Hydrodynamics ◽  
Smoothed Particle ◽  
Meshless Approximation ◽  
Complex Phenomena

In this paper, we propose a Galerkin-based smoothed particle hydrodynamics (SPH) formulation with moving least-squares meshless approximation, applied to solid mechanics and large deformation. Our method is truly meshless and based on Lagrangian kernel formulation and stabilized nodal integration. The performance of the methodology proposed is tested through various simulations, demonstrating the attractive ability of particle methods to handle severe distortions and complex phenomena.

scholarly journals SPH Simulations of the Chemical and Dynamical Evolution of the Galactic Bulge

1993 ◽  
Vol 153 ◽  
pp. 395-396
Author(s):  
T. Tsujimoto ◽  
K. Nomoto ◽  
T. Shigeyama ◽  
Y. Ishimaru
Keyword(s):  
Distribution Function ◽  
Galaxy Formation ◽  
Smoothed Particle Hydrodynamics ◽  
Heavy Element ◽  
Dynamical Evolution ◽  
Galactic Bulge ◽  
Abundance Distribution ◽  
Sph Method ◽  
Particle Hydrodynamics ◽  
Smoothed Particle

We simulate the chemical and dynamical evolution of the galactic bulge with the smoothed particle hydrodynamics (SPH) method. We calculate the early phase of galaxy formation in which the bulge is formed through a burst of star formation. The calculated abundance distribution function of stars in the bulge is consistent with the observations of bulge K giants, if the heavy element yields are three times larger than those expected from Salpeter's IMF.

Sign in / Sign up

Export Citation Format

Share Document