scholarly journals Green-light Supplementation for Enhanced Lettuce Growth under Red- and Blue-light-emitting Diodes

HortScience ◽  
2004 ◽  
Vol 39 (7) ◽  
pp. 1617-1622 ◽  
Author(s):  
Hyeon-Hye Kim ◽  
Gregory D. Goins ◽  
Raymond M. Wheeler ◽  
John C. Sager
Keyword(s):  
Plant Growth ◽  
Light Source ◽  
Blue Light ◽  
Light Emitting Diodes ◽  
Green Light ◽  
Light Sources ◽  
Natural Setting ◽  
Light Emitting ◽  
Fluorescent Lamps ◽  
Green Fluorescent

Plants will be an important component of future long-term space missions. Lighting systems for growing plants will need to be lightweight, reliable, and durable, and light-emitting diodes (LEDs) have these characteristics. Previous studies demonstrated that the combination of red and blue light was an effective light source for several crops. Yet the appearance of plants under red and blue lighting is purplish gray making visual assessment of any problems difficult. The addition of green light would make the plant leave appear green and normal similar to a natural setting under white light and may also offer a psychological benefit to the crew. Green supplemental lighting could also offer benefits, since green light can better penetrate the plant canopy and potentially increase plant growth by increasing photosynthesis from the leaves in the lower canopy. In this study, four light sources were tested: 1) red and blue LEDs (RB), 2) red and blue LEDs with green fluorescent lamps (RGB), 3) green fluorescent lamps (GF), and 4) cool-white fluorescent lamps (CWF), that provided 0%, 24%, 86%, and 51% of the total PPF in the green region of the spectrum, respectively. The addition of 24% green light (500 to 600 nm) to red and blue LEDs (RGB treatment) enhanced plant growth. The RGB treatment plants produced more biomass than the plants grown under the cool-white fluorescent lamps (CWF treatment), a commonly tested light source used as a broad-spectrum control.

scholarly journals Sugarcane micropropagation using light emitting diodes and adjustment in growth-medium sucrose concentration

2013 ◽  
Vol 43 (7) ◽  
pp. 1168-1173 ◽  
Author(s):  
Paulo Sérgio Gomes da Rocha ◽  
Roberto Pedroso de Oliveira ◽  
Walkyria Bueno Scivittaro
Keyword(s):  
Light Source ◽  
Growth Medium ◽  
Light Emitting Diodes ◽  
Sucrose Concentration ◽  
Saccharum Officinarum ◽  
Growth Media ◽  
Light Sources ◽  
Multiplication Rate ◽  
Light Emitting ◽  
Fluorescent Lamps

The aim of this research was to evaluate the use of light emitting diodes (LEDs) instead of white fluorescent lamps as light source and adequate growth-medium sucrose concentration for sugarcane micropropagation (Saccharum officinarum L.). Sugarcane (RB 872552 variety) bud explants were evaluated during the multiplication and rooting phases under controlled growth-room conditions. Different light sources (blue, red and green LEDs; Growlux and white fluorescent lamps) and different medium sucrose concentrations (0; 15; 30 and 45g L-1) were used, maintaining constant light intensity (20µmol m-2 s-1), photoperiod (16h) and temperature (25+2°C). The experiment was a completely randomized design, and treatments were arranged in a 5x4 factorial (five light sources and four medium sucrose concentrations) with six replications. Sugarcane bud growth was satisfactory under the three LED types studied. The presence of sucrose in growth media was essential for bud multiplication and rooting. Nevertheless, each light source requires the respective medium sucrose concentration adjustment for best results. Red LEDs provided a significantly high multiplication rate (although not the highest) with 8.5 buds per sub-culture and 34.9g L-1 of sucrose; also, the highest bud length (33.3mm) and the best plantlet acclimatization. Therefore, LED sources can advantageously substitute fluorescent lamps in laboratories of sugarcane micropropagation.

scholarly journals Application of Light-Emitting Diodes for Improving the Nutritional Quality and Bioactive Compound Levels of Some Crops and Medicinal Plants

Molecules ◽  
2021 ◽  
Vol 26 (5) ◽  
pp. 1477
Author(s):  
Woo-Suk Jung ◽  
Ill-Min Chung ◽  
Myeong Ha Hwang ◽  
Seung-Hyun Kim ◽  
Chang Yeon Yu ◽  
...  
Keyword(s):  
Plant Growth ◽  
In Vitro Culture ◽  
Light Emitting Diodes ◽  
Photosynthetic Pigment ◽  
Antioxidant Properties ◽  
Light Sources ◽  
Light Emitting ◽  
Cell Defense ◽  
Led Irradiation

Light is a key factor that affects phytochemical synthesis and accumulation in plants. Due to limitations of the environment or cultivated land, there is an urgent need to develop indoor cultivation systems to obtain higher yields with increased phytochemical concentrations using convenient light sources. Light-emitting diodes (LEDs) have several advantages, including consumption of lesser power, longer half-life, higher efficacy, and wider variation in the spectral wavelength than traditional light sources; therefore, these devices are preferred for in vitro culture and indoor plant growth. Moreover, LED irradiation of seedlings enhances plant biomass, nutrient and secondary metabolite levels, and antioxidant properties. Specifically, red and blue LED irradiation exerts strong effects on photosynthesis, stomatal functioning, phototropism, photomorphogenesis, and photosynthetic pigment levels. Additionally, ex vitro plantlet development and acclimatization can be enhanced by regulating the spectral properties of LEDs. Applying an appropriate LED spectral wavelength significantly increases antioxidant enzyme activity in plants, thereby enhancing the cell defense system and providing protection from oxidative damage. Since different plant species respond differently to lighting in the cultivation environment, it is necessary to evaluate specific wavebands before large-scale LED application for controlled in vitro plant growth. This review focuses on the most recent advances and applications of LEDs for in vitro culture organogenesis. The mechanisms underlying the production of different phytochemicals, including phenolics, flavonoids, carotenoids, anthocyanins, and antioxidant enzymes, have also been discussed.

scholarly journals Effects of Frequency and Duty Ratio on the Growth of Potato Plantlets In Vitro Using Light-emitting Diodes

HortScience ◽  
2004 ◽  
Vol 39 (2) ◽  
pp. 375-379 ◽  
Author(s):  
Ruey-Chi Jao ◽  
Wei Fang
Keyword(s):  
Plant Growth ◽  
Light Emitting Diodes ◽  
Heat Removal ◽  
Duty Ratio ◽  
Intermittent Light ◽  
Light Emitting ◽  
Fluorescent Lamps ◽  
Fluctuating Light ◽  
Potato Plantlets

Effects of intermittent light on photomixotrophic growth of potato plantlets in vitro and the electrical savings that could be realized by adjusting the frequency and duty ratio of light-emitting diodes (LEDs) were investigated and compared to the use of conventional tubular fluorescent lamps (TFLs). TFLs provide continuous fluctuating light at 60 Hz and LEDs provide continuous nonfluctuating or intermittent/pulse light depend on the preset frequency and duty ratio. In total, eight treatments were investigated with varying light source, frequency, duty ratio and photoperiod. Results indicated that if growth rate is the only concern, LEDs at 720 Hz [1.4 milliseconds (ms)] and 50% duty ratio with 16-h light/8-h dark photoperiod stimulated plant growth the most. However, if energy consumption is the major concern, using LEDs at 180 Hz (5.5 ms) and 50% duty ratio with 16-h light/8-h dark photoperiod would be the best choice for illuminating potato plantlets without significantly sacrificing plant growth, especially when energy for heat removal is also considered.

Safest light in a combat area while performing intravenous access in the dark

2018 ◽  
Vol 164 (5) ◽  
pp. 343-346 ◽  
Author(s):  
Attila Aydin ◽  
S Bilge ◽  
M Eryilmaz
Keyword(s):  
Light Source ◽  
Blue Light ◽  
Green Light ◽  
Night Vision ◽  
Infrared Light ◽  
Light Sources ◽  
Night Time ◽  
Naked Eye ◽  
Prehospital Management ◽  
Dark Room

IntroductionCannulation for the administration of intravenous fluids is integral to the prehospital management of injured military patients. However, this may be technically challenging to undertake during night-time conditions where the use of light to aid cannulation may give the tactical situation away to opponents. The aim of this study was to investigate the success and tactical safety of venepuncture under battlefield conditions with different colour light sources.MethodThe procedure was carried out with naked eye in a bright room in the absence of a separate light source, with a naked eye in a dark room under red, white, blue and green light sources and under an infrared light source while wearing night vision goggles (NVGs). The success, safety, degree of difficulty and completion time for each procedure were then explored.ResultsAll interventions made in daylight and in a dark room were found to be 100% successful. Interventions performed under infrared light while wearing NVGs took longer than under other light sources or in daylight. Interventions performed under blue light were tactically safer when compared with interventions performed under different light sources.ConclusionBlue light offered the best tactical safety during intravenous cannulation under night-time conditions and is recommended for future use in tactical casualty care. The use of NVGs using infrared light cannot be recommended if there is the possibility of opponents having access to the technology.

Performance of Arabidopsis thaliana under different light qualities: comparison of light-emitting diodes to fluorescent lamp

2017 ◽  
Vol 44 (7) ◽  
pp. 727 ◽  
Author(s):  
Karin Köhl ◽  
Takayuki Tohge ◽  
Mark Aurel Schöttler
Keyword(s):  
Arabidopsis Thaliana ◽  
Light Source ◽  
Light Emitting Diodes ◽  
Seed Mass ◽  
Fluorescent Light ◽  
Chlorophyll Fluorescence Parameters ◽  
Light Emitting ◽  
Led Light ◽  
Improve Energy Efficiency ◽  
Fluorescent Lamps

For precise phenotyping, Arabidopsis thaliana (L.) Heynh. is grown under controlled conditions with fluorescent lamps as the predominant light source. Replacement by systems based on light emitting diodes (LED) could improve energy efficiency and stability of light quality and intensity. To determine whether this affects the reproducibility of results obtained under fluorescent lamps, four Arabidopsis accessions and a phytochrome mutant were grown and phenotyped under two different LED types or under fluorescent lamps. All genotypes had significantly higher rosette weight and seed mass and developed faster under LED light than under fluorescent lamps. However, differences between genotypes were reproducible independent of the light source. Chlorophyll content, photosynthetic complex accumulation and light response curves of chlorophyll fluorescence parameters were indistinguishable under LED and fluorescent light. Principal component analysis of leaf metabolite concentrations revealed that the effect of a change from fluorescent light to LED light was small compared with the diurnal effect, which explains 74% of the variance and the age effect during vegetative growth (12%). Altogether, the replacement of fluorescent lamps by LED allowed Arabidopsis cultivation and reproduction of results obtained under fluorescent light.

scholarly journals Optical System for Led Luminaire

2019 ◽  
pp. 62-67
Author(s):  
A. Kolesnyk
Keyword(s):  
Light Source ◽  
Light Emitting Diodes ◽  
New Technology ◽  
Light Distribution ◽  
Optical Systems ◽  
Light Sources ◽  
Optical Elements ◽  
Light Emitting ◽  
The Right ◽  
Led Luminaire

Lighting devices are an important element of a large number of technical systems, including road, living, industrial lighting, lighting systems of vehicles. It is known that the light instrument must fulfill two basic lighting tasks: to redistribute the light source of light source in the right way and to limit its dazzling effect. The introduction of light-emitting diodes (LEDs) for lighting necessitated a completely new quality in the construction of luminaires. The different production technology required new methods and designing tools. It also challenged designers with new problems to solve. LEDs are light sources emitting in one hemisphere, which requires a special approach to designing an LED lighting unit. However, for the illumination of premises with high spans or streets, roads such a light distribution is not suitable. For luminaires with solid-state light sources, other materials and new technology must be used; moreover, light distribution needs to be formed using different methods. This paper presents the design process of a LED luminaire from concept to implementation, exemplified by road lighting, and describes the methods and procedures used by the designer. Also, technological problems influencing the quality of the above lighting are addressed. Optical systems for LEDs are considered. The peculiarities of the use of secondary optical elements in the form of lenses for purpose of obtaining different diagrams of the spatial distribution of light intensity of light-emitting diodes are analyzed. Features and problems of calculation of secondary optical systems are considered. Massive collimators do not have to be elements that focus a narrow beam of light. They are able to form a beam in accordance with any accepted distribution that is appropriate for a given application. They are also able to form a beam in a specific way that is required for outdoor lighting luminaires. The stages of a project for designing a road luminaire require the application of the knowledge and experience gained in various research projects. The design methods described in this paper have been developed designing activity and are also to be used successfully in lighting production.  

Sign in / Sign up

Export Citation Format

Share Document