Developing Forensic Investigation Standards to Effectively Deal with Structural Failures

2019 ◽  
Author(s):  
Ankita Patil ◽  
Vandana Bhatt ◽  
Anil Nivrati Ghadg
Author(s):  
Shubham N. Dadgal ◽  
Shrikant Solanke

In modern days for structures in coastal areas it has been observed that the premature structural failures are occurs due to corrosion of the reinforcements of the designed structural member. The corrosion causes the structural damage which in turn leads to reduction in the bearing capacity of the concerned structural members. The aim of this study was to study the effect of partial replacement of fly ash to minimize the corrosion effect. Beams were designed and corroded by using artificial method known accelerated corrosion method. The beams were then tested for flexural and bond strength. Also the weight loss of the reinforced bars was been determined using electrical resistivity method. The fly ash will replace by 10% and 15%.The strength will calculate at varying percentage of corrosion at 10% and 15%. Beams will cast at M25 grade concrete. The flexural strength will test by using UTM and the bond strength will calculate using pullout test.


1988 ◽  
Vol 16 (3) ◽  
pp. 146-170 ◽  
Author(s):  
S. Roy ◽  
J. N. Reddy

Abstract A good understanding of the process of adhesion from the mechanics viewpoint and the predictive capability for structural failures associated with adhesively bonded joints require a realistic modeling (both constitutive and kinematic) of the constituent materials. The present investigation deals with the development of an Updated Lagrangian formulation and the associated finite element analysis of adhesively bonded joints. The formulation accounts for the geometric nonlinearity of the adherends and the nonlinear viscoelastic behavior of the adhesive. Sample numerical problems are presented to show the stress and strain distributions in bonded joints.


Author(s):  
Arun Kumar Karunanithi ◽  
Joseph Caroselli ◽  
Jason Christensen ◽  
Michell Espitia

Abstract Laser Assisted Device Alteration (LADA) or Soft Defect Localization (SDL) is commonly used to root cause device marginality due to functional or structural failures. At a high level, LADA involves setting the device under test (DUT) at its marginal state and using focused near infra-red laser beams to perturb sensitive circuitry [1]. Scanning the focused laser beam over the die can be a long and time-consuming process. In this paper, two LADA cases are presented, which involve a parametric measurement failure while running a dynamic ATE test. Using LADA technique, these two cases were root caused. These two cases also explain how a parametric measurement-based LADA can be setup on ATE, as well as a synchronization method independent of vectors in a pattern. Synchronization was necessitated in the 2nd case due to the asymmetric test program loop, as well as the long test program cycle time. There are many factors which impact LADA turnaround time and it can take anywhere between few seconds to one day. The two major factors are the size of the Area of Interest (AOI) and test program cycle time. Test program cycle time influences the laser “dwell time” for LADA. Dwell time, in simple terms, is the total time the laser is parked at each pixel. The laser can also be synchronized with the test program cycle, keeping the two always in phase. This is explained in Case 2, where LADA synchronization was implemented, and the analysis was successfully completed in time, even though the test cycle time was very long.


2019 ◽  
Vol 8 (3) ◽  
pp. 5926-5929

Blind forensic-investigation in a digital image is a new research direction in image security. It aims to discover the altered image content without any embedded security scheme. Block and key point based methods are the two dispensation options in blind image forensic investigation. Both the techniques exhibit the best performance to reveal the tampered image. The success of these methods is limited due to computational complexity and detection accuracy against various image distortions and geometric transformation operations. This article introduces different blind image tampering methods and introduces a robust image forensic investigation method to determine the copy-move tampered image by means of fuzzy logic approach. Empirical outcomes facilitate that the projected scheme effectively classifies copy-move type of forensic images as well as blurred tampered image. Overall detection accuracy of this method is high over the existing methods.


Water ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 1787
Author(s):  
Leena J. Shevade ◽  
Franco A. Montalto

Green infrastructure (GI) is viewed as a sustainable approach to stormwater management that is being rapidly implemented, outpacing the ability of researchers to compare the effectiveness of alternate design configurations. This paper investigated inflow data collected at four GI inlets. The performance of these four GI inlets, all of which were engineered with the same inlet lengths and shapes, was evaluated through field monitoring. A forensic interpretation of the observed inlet performance was conducted using conclusions regarding the role of inlet clogging and inflow rate as described in the previously published work. The mean inlet efficiency (meanPE), which represents the percentage of tributary area runoff that enters the inlet was 65% for the Nashville inlet, while at Happyland the NW inlet averaged 30%, the SW inlet 25%, and the SE inlet 10%, considering all recorded events during the monitoring periods. The analysis suggests that inlet clogging was the main reason for lower inlet efficiency at the SW and NW inlets, while for the SE inlet, performance was compromised by a reverse cross slope of the street. Spatial variability of rainfall, measurement uncertainty, uncertain tributary catchment area, and inlet depression characteristics are also correlated with inlet PE. The research suggests that placement of monitoring sensors should consider low flow conditions and a strategy to measure them. Additional research on the role of various maintenance protocols in inlet hydraulics is recommended.


2021 ◽  
pp. 1-13
Author(s):  
Candice C. Chua ◽  
Honoria Kwok ◽  
Jeffrey Yan ◽  
Daniel Cuthbertson ◽  
Graham van Aggelen ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document