scholarly journals Application of polymeric ferric sulfate combined with cross-frequency magnetic field in the printing and dyeing wastewater treatment

2019 ◽  
Vol 80 (8) ◽  
pp. 1562-1570
Author(s):  
Shiguo Gu ◽  
Fei Lian ◽  
Kejun Yan ◽  
Wei Zhang
Keyword(s):  
Magnetic Field ◽  
Wastewater Treatment ◽  
Removal Rate ◽  
Oxygen Demand ◽  
Ferric Sulfate ◽  
Dyeing Wastewater ◽  
Printing And Dyeing Wastewater ◽  
Magnetization Intensity ◽  
Frequency Magnetic Field

Abstract Polymeric ferric sulfate (PFS) was pretreated with a self-made alternating frequency magnetic field for coagulation printing and dyeing (PD) wastewater treatment. The effects of PFS dosage, magnetization intensity, frequency, and time on the removal of chemical oxygen demand (COD), color and turbidity of PD wastewater were investigated. The results indicated that the magnetized PFS significantly improved the removal efficiency in wastewater treatment. When the initial COD, color and turbidity of printing and dyeing wastewater was 464 mg/L, 180 degrees, and 54.8 NTU respectively, the maximum removal rate of COD, color and turbidity was 87.9%, 80.1%, and 95.2% respectively, under the condition of cross frequency magnetic field magnetization PFS. Moreover, the PFS treatment combined with cross-frequency magnetic field could greatly reduce the pollution of iron ions released from iron-based coagulant during wastewater treatment. Characterization of magnetized PFS flocculant by fourier transform infrared spectroscopy, ultraviolet and visible spectrophotometry, and scanning electron microscopy suggested that magnetic crystal with larger size can be formed on the surface of PFS particles.

scholarly journals Preparation of Mn/Mg/Ce Ternary Ozone Catalyst and Its Mechanism for the Degradation of Printing and Dyeing Wastewater

2022 ◽  
Vol 9 ◽  
Author(s):  
Shuai Zhang ◽  
Huixue Ren ◽  
Kaifang Fu ◽  
Wenqing Cheng ◽  
Daoji Wu ◽  
...  
Keyword(s):  
Methyl Orange ◽  
Catalytic Oxidation ◽  
Removal Rate ◽  
Dynamic Test ◽  
Oxygen Demand ◽  
Dyeing Wastewater ◽  
Printing And Dyeing Wastewater ◽  
Treatment Conditions ◽  
Nano Alumina ◽  
Catalyst Dosage

The printing and dyeing wastewater produced by different dyes, as well as different printing and dyeing processes, have different components. These wastewater have high toxicity, high organic concentration, and deep chromaticity. Ozone catalytic oxidation is a very promising technical method for wastewater treatment. In this paper, Mn/Mg/Ce ternary catalyst was prepared, and the ozone catalytic oxidation treatment of actual and simulated printing and dyeing wastewater was performed to study the performance of four different carrier catalysts, namely, molecular sieve (MS), silica gel (SG), attapulgite (ATP), and nano alumina (Al2O3), by simulated dynamic test. The effects of reaction time, pH, and catalyst dosage on methyl orange degradation were studied. The results showed that under the optimum treatment conditions (120 min, pH 11, and 12.5 g/L catalyst dosage), the degradation rate of methyl orange reached 96% and the removal rate of the chemical oxygen demand of printing and dyeing wastewater reached 48.7%. This study shows that the treatment effect of ozone catalytic oxidation on printing and dyeing wastewater is remarkably improved after catalyst addition. This study provides a new choice of ozone catalyst for the degradation of printing and dyeing wastewaters in the future.

scholarly journals Pretreatment of printing and dyeing wastewater by Fe/C micro-electrolysis combined with H2O2 process

2018 ◽  
Vol 2017 (3) ◽  
pp. 707-717 ◽  
Author(s):  
Yan Wang ◽  
Xianwei Wu ◽  
Ju Yi ◽  
Lijun Chen ◽  
Tianxiang Lan ◽  
...  
Keyword(s):  
Removal Rate ◽  
Oxygen Demand ◽  
Cod Removal ◽  
Coefficient Of Determination ◽  
H2o2 Concentration ◽  
Dyeing Wastewater ◽  
Spectra Analysis ◽  
Printing And Dyeing Wastewater ◽  
Initial Ph ◽  
Cod Removal Rate

Abstract A novel iron-carbon (Fe/C) micro-electrolysis combined with H2O2 (ICMH) process was proposed to pretreat the printing and dyeing wastewater (PDW), using a micro-electrolysis filling. The effects of H2O2 concentration, reaction time, initial pH, and Fe/C dosage on chemical oxygen demand (COD) removal rate of PDW were optimized by response surface methodology (RSM). The maximum COD removal rate was approximately 77.65% after 186 min treatment, when the concentration of H2O2, initial pH and the dosage of Fe/C were 8.88 g/L, 1.5 and 837 g/L, respectively. Analysis of variance (ANOVA) showed a high coefficient of determination value (R2 = 0.9780). And H2O2 concentration and initial pH were the key factors to improve the treatment effect. UV-Vis spectra indicated that a significant blue shift at 220 nm, attributing that fused aromatic hydrocarbons were degraded effectively. 3D-EEM spectra analysis showed that the water samples of PDW mainly contained three kinds of organic matter: refractory fulvic acid, soluble microbial metabolites and aromatic proteins, and the degradation rate of these was 81.76%, 53.78% and 70.83%, respectively.

Research on the Characteristic of Dyeing-Printing Wastewater Treatment with Micro-Aerobic Granular Sludge

2013 ◽  
Vol 726-731 ◽  
pp. 2757-2760
Author(s):  
Ling Feng Zhu ◽  
Dou Dou Huang ◽  
Chao Ye ◽  
Xiao Min Wang ◽  
Jie Yan Wu ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Dissolved Oxygen ◽  
Removal Rate ◽  
Control Valve ◽  
Aerobic Condition ◽  
Granular Sludge ◽  
Aerobic Granular Sludge ◽  
Dyeing Wastewater ◽  
Printing And Dyeing Wastewater ◽  
Mixed Water

In order to treat dyeing-printing wastewater, the experiment took reflux tank, self-regulating control valve making of medical infusion, air flow meter, dissolved oxygen instrument, aerator pumps and aeration equipment under the micro-aerobic condition by IC reactor. The result indicates that the concentration of dissolved oxygen at 0.3 ~ 0.5 mg/L, increasing the load of mixed water and in-flow water by 25% and 7% separately in turn, the experiment is feasible. When COD load reached 2188.2 mg/ L in the mixed wastewater, the components in printing and dyeing wastewater are poisonous and repressive to the grown of granular sludge, which also illuminates that the function of micro-aerobic granular sludge treating printing and dyeing wastewater is limitary. When the influent load reached 4655.1mg / L or so, dissolved oxygen was 0.3 ~ 0.5mg / L, HRT was 6h, the reactor worked best, this moment, the removal rate of COD could reach 85.8%.

scholarly journals Isolation and characterization of organic matter-degrading bacteria from coking wastewater treatment plant

2018 ◽  
Vol 78 (7) ◽  
pp. 1517-1524 ◽  
Author(s):  
Riqiang Li ◽  
Jianxing Wang ◽  
Hongjiao Li
Keyword(s):  
Organic Matter ◽  
Wastewater Treatment ◽  
Wastewater Treatment Plant ◽  
Removal Rate ◽  
Treatment Plant ◽  
Coking Wastewater ◽  
Naphthalene Degradation ◽  
Isolation And Characterization ◽  
Degrading Bacteria

Abstract As a step toward bioaugmentation of coking wastewater treatment 45 bacteria strains were isolated from the activated sludge of a coking wastewater treatment plant (WWTP). Three strains identified as Bacillus cereus, Pseudomonas synxantha, and Pseudomonas pseudoaligenes exhibited high dehydrogenase activity which indicates a strong ability to degrade organic matter. Subsequently all three strains showed high naphthalene degradation abilities. Naphthalene is a refractory compound often found in coking wastewater. For B. cereus and P. synxantha the maximum naphthalene removal rates were 60.4% and 79.8%, respectively, at an initial naphthalene concentration of 80 mg/L, temperature of 30 °C, pH of 7, a bacteria concentration of 15% (V/V), and shaking speed of 160 r/min. For P. pseudoaligenes, the maximum naphthalene removal rate was 77.4% under similar conditions but at 35 °C.

Characterization of New Nonstoichiometric Ferroelectric (Li0.95Cu0.15)Ta0.76Nb0.19O3 and Comparative Study With (Li0.95Cu0.15)Ta0.57Nb0.38O3 as Photocatalysts in Microbial Fuel Cells

2018 ◽  
Vol 16 (2) ◽  
Author(s):  
S. Louki ◽  
N. Touach ◽  
A. Benzaouak ◽  
V. M. Ortiz-Martínez ◽  
M. J. Salar-García ◽  
...  
Keyword(s):  
Power Density ◽  
Microbial Fuel Cells ◽  
Removal Rate ◽  
Oxygen Demand ◽  
Ferroelectric Material ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Uv Visible

This work investigates the photocatalytic activity of new ferroelectric material with formula (Li0.95Cu0.15)Ta0.76Nb0.19O3 (LT76) in a single chamber microbial fuel cell (MFC) and compares its performance with the similar photocatalyst (Li0.95Cu0.15)Ta0.57Nb0.38O3 (LT57). The photocatalysts LT76 and LT57 were synthesized by ceramic route under the same conditions, with the same starting materials. The ratio Ta/Nb was fixed at 4.0 and 1.5 for LT76 and LT57, respectively. These phases were characterized by different techniques including X-ray diffraction (XRD), transmission electronic microscopy (TEM), particle size distribution (PSD), differential scanning calorimetry (DSC), and ultraviolet (UV)–visible (Vis). The new photocatalyst LT76 presents specific surface area of 0.791 m2/g and Curie temperature of 1197 °C. The photocatalytic efficiency of this material is assessed in terms of wastewater treatment and electricity generation by power density and removal rate of chemical oxygen demand (COD) in the presence of a light source. The values of maximum power density and COD removal were 19.77 mW/m3 and 93%, respectively, for LT76.

scholarly journals Investigation of the Efficiency of Phosphorus Removal Using Anionic Resins From the Continuous Flow in the Waste Stabilization Pond Outlet: A Case Study of Kaboodrahang Wastewater Treatment Plant

2019 ◽  
Vol 6 (1) ◽  
pp. 16-20
Author(s):  
Ali Akbar Rahmani Sarmazdeh ◽  
Mostafa Leili
Keyword(s):  
Wastewater Treatment ◽  
Wastewater Treatment Plant ◽  
Phosphorus Removal ◽  
Continuous Flow ◽  
Removal Rate ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Cold Season ◽  
Stabilization Pond ◽  
The Mean

This research mainly aimed to investigate phosphorus removal from stabilization pond effluent by using anionic resins in the continuous flow mode of operation due to high amounts of phosphorus in the wastewater treatment plant effluent of Kaboodrahang, western Iran, as well as the violation from a prescribed effluent standard to discharge receiving the surface waters. For this purpose, the pilot was made of a plexiglass cylinder and other equipment such as pump and other accessories, as well as Purolite A-100 resin. The reactor effects on the desired study parameters were assessed in two warm and cold seasons. The results showed that the phosphorus concentrations reduced from 7-10 mg/L to 4-7 mg/L and the rate of phosphorus removal was higher in the hot season compared to the cold season. Moreover, the optimum temperature and pH were obtained 21ºC and 8.5, respectively. The mean inlet biological oxygen demand (BOD) was 150 mg/L for both warm and cold seasons, where the highest removal rate of 17% was obtained in the cold season. The mean chemical oxygen demand concentration of the pilot was 250 mg/L for both seasons, and the highest removal rate was observed in the cold season with an efficiency of 18%. Regarding the total suspended solids with the mean inlet of 230 mg/L, the highest removal efficiency was obtained 6% in the warm season.

Electrochemical oxidative degradation of indigo wastewater based on chlorine-containing system

2020 ◽  
Vol 49 (1) ◽  
pp. 46-54 ◽  
Author(s):  
Wei Zhang ◽  
Weiwei Lv ◽  
Xiaoyan Li ◽  
Jiming Yao
Keyword(s):  
Chemical Oxygen Demand ◽  
Response Surface ◽  
Electrochemical Oxidation ◽  
Surface Analysis ◽  
Removal Rate ◽  
Oxidative Degradation ◽  
Oxygen Demand ◽  
Single Factor ◽  
Dyeing Wastewater ◽  
Content Type

Purpose In this study, the oxidative degradation performance of indigo wastewater based on electrochemical systems was explored. The decolourization degrees, removal rate of chemical oxygen demand and biochemical oxygen demand of the indigo wastewater after degradation were evaluated and optimized treatment conditions being obtained. Design/methodology/approach The single factor method was first used to select the electrolyte system and electrode materials. Then the response surface analysis based on Box–Behnken Design was chosen to determine the influence of four independent variables such as FeCl3 concentration, NaCl concentration, decolourization time and voltage on the degradation efficiency. Findings On the basis of single factor experiment, the electrode material of stainless steel was selected in the double cell, and the indigo wastewater was electrolyzed with FeCl3 and NaCl electrolytes. The process conditions of electrochemical degradation of indigo wastewater were optimized by response surface analysis: the concentration of FeCl3 and NaCl was of 16 and 9 g/L, respectively, with a decolourization time of 50 min, voltage of 10 V and decolourization percentage of 98.94. The maximum removal rate of chemical oxygen demand reached 75.46 per cent. The highest ratio of B/C was 3.77, which was considered to be more biodegradable. Research limitations/implications Dyeing wastewater is bringing out more and more pollution problems to the environment. However, there are some shortcomings in traditional technologies such as adsorption and filtration. As a kind of efficient and clean water treatment technology, electrochemical oxidation has been applied to the treatments of various types of wastewater. The decolourization and degradation of indigo wastewater is taken as an example to provide reference for the treatment of wastewater in actual plants. Practical implications The developed method provided a simple and practical solution for efficiently degrading indigo wastewater. Originality/value The method for the electrochemical oxidation technology was novel and could find numerous applications in the degradation of printing and dyeing wastewater.

Preparation of a New Adsorption Material and its Application in Wastewater Treatment

2011 ◽  
Vol 356-360 ◽  
pp. 498-501
Author(s):  
Wen Jie Jin ◽  
Fan Chao Zeng ◽  
Han Xue ◽  
Ying Wang
Keyword(s):  
Wastewater Treatment ◽  
Activated Carbon ◽  
Carbon Materials ◽  
Advanced Treatment ◽  
Coking Wastewater ◽  
Biochemical Process ◽  
Effluent Water ◽  
Dyeing Wastewater ◽  
Printing And Dyeing Wastewater ◽  
New Material

A kind of new adsorption material for wastewater treatment was made of fly ash as the main composition, with addition of sodium silicate, cement and pore forming material as the accessory materials, etc. Three kinds of practical wastewater were treated by using the new material, they were printing and dyeing wastewater, papermaking wastewater and coking wastewater, respectively. The results showed that removal COD efficiencies of the three kinds of wastewater were 57.89%, 71.43%, 80%, respectively, removal color efficiencies were 90%, 92%, 92%, respectively. The new developed material was mainly used for advanced treatment of the effluent water after biochemical process. It will be a substitute for activated carbon materials and have preferable application prospect.

Sign in / Sign up

Export Citation Format

Share Document