scholarly journals MEASUREMENTS OF THE THERMAL CONDUCTIVITY OF SOILS TO HIGH TEMPERATURES. Final Report.

1969 ◽  
Author(s):  
D.R. Flynn ◽  
T.W. Watson
Keyword(s):  
Thermal Conductivity ◽  
High Temperatures ◽  
Final Report

TWO-PHASE THERMAL CONDUCTIVITY OF CERAMIC SPONGES WITH AND WITHOUT FLOW UP TO HIGH TEMPERATURES

2018 ◽  
Author(s):  
Thomas Fischedick ◽  
Konrad Dubil ◽  
Benjamin Dietrich
Keyword(s):  
Thermal Conductivity ◽  
High Temperatures ◽  
Two Phase

Thermal Conductivity of Nitrogen at High Temperatures and Pressures

1957 ◽  
Vol 49 (12) ◽  
pp. 2040-2041 ◽  
Author(s):  
P. Johannin ◽  
B. Vodar
Keyword(s):  
Thermal Conductivity ◽  
High Temperatures

scholarly journals Frequency-domain hot-wire sensor and 3D model for thermal conductivity measurements of reactive and corrosive materials at high temperatures

2020 ◽  
Vol 91 (5) ◽  
pp. 054904 ◽  
Author(s):  
M. C. Wingert ◽  
A. Z. Zhao ◽  
Y. Kodera ◽  
S. J. Obrey ◽  
J. E. Garay
Keyword(s):  
Thermal Conductivity ◽  
Frequency Domain ◽  
High Temperatures ◽  
3D Model ◽  
Conductivity Measurements ◽  
Hot Wire

Effects of Nb doping on thermoelectric properties of Zn4Sb3 at high temperatures

2009 ◽  
Vol 24 (2) ◽  
pp. 430-435 ◽  
Author(s):  
D. Li ◽  
H.H. Hng ◽  
J. Ma ◽  
X.Y. Qin
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
High Temperatures ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Thermoelectric Performance ◽  
Temperature Range ◽  
A Value ◽  
Nb Doping ◽  
Thermal Conductivities

The thermoelectric properties of Nb-doped Zn4Sb3 compounds, (Zn1–xNbx)4Sb3 (x = 0, 0.005, and 0.01), were investigated at temperatures ranging from 300 to 685 K. The results showed that by substituting Zn with Nb, the thermal conductivities of all the Nb-doped compounds were lower than that of the pristine β-Zn4Sb3. Among the compounds studied, the lightly substituted (Zn0.995Nb0.005)4Sb3 compound exhibited the best thermoelectric performance due to the improvement in both its electrical resistivity and thermal conductivity. Its figure of merit, ZT, was greater than the undoped Zn4Sb3 compound for the temperature range investigated. In particular, the ZT of (Zn0.995Nb0.005)4Sb3 reached a value of 1.1 at 680 K, which was 69% greater than that of the undoped Zn4Sb3 obtained in this study.

ON MEASUREMENT OF THERMAL CONDUCTIVITY AT HIGH TEMPERATURES

1961 ◽  
Vol 39 (7) ◽  
pp. 1029-1039 ◽  
Author(s):  
M. J. Laubitz
Keyword(s):  
Thermal Conductivity ◽  
Heat Flow ◽  
High Temperatures ◽  
Mathematical Analysis ◽  
Temperature Range ◽  
Linear Heat ◽  
Flow Systems

A method is given for exact mathematical analysis of linear heat flow systems used in measuring thermal conductivity at high temperatures. It is shown that a popular version of such a system is very sensitive to the alignment of its components, which seriously limits the temperature range of its satisfactory use.

Thermal Conductivity of Sintered UO, and Al2O3 at High Temperatures

1965 ◽  
Vol 48 (1) ◽  
pp. 31-34 ◽  
Author(s):  
TORAJI NISHIJIMA ◽  
TOSHIYUKI KAWADA ◽  
AKIRA ISHIHATA
Keyword(s):  
Thermal Conductivity ◽  
High Temperatures

scholarly journals Study of the Turning Nickel Base Alloy Pyromet® 31V (SAE HEV8)

2011 ◽  
Vol 278 ◽  
pp. 312-320 ◽  
Author(s):  
Marcos Valério Ribeiro ◽  
André Luís Habib Bahia
Keyword(s):  
Thermal Conductivity ◽  
Mechanical Strength ◽  
High Temperatures ◽  
Base Alloy ◽  
Production Costs ◽  
Machining Parameters ◽  
Nickel Base Alloy ◽  
Low Thermal Conductivity ◽  
Nickel Base ◽  
Coated Carbide

Considering the constant technological developments in the aeronautical, space, automotive, shipbuilding, nuclear and petrochemical fields, among others, the use of materials with high strength mechanical capabilities at high temperatures has been increasingly used. Among the materials that meet the mechanical strength and corrosion properties at temperatures around 815 °C one can find the nickel base alloy Pyromet® 31V (SAE HEV8). This alloy is commonly applied in the manufacturing of high power diesel engines exhaust valves where it is required high resistance to sulphide, corrosion and good resistance to creep. However, due to its high mechanical strength and low thermal conductivity its machinability is made difficult, creating major challenges in the analysis of the best combinations among machining parameters and cutting tools to be used. Its low thermal conductivity results in a concentration of heat at high temperatures in the interfaces of workpiece-tool and tool-chip, consequently accelerating the tools wearing and increasing production costs. This work aimed to study the machinability, using the carbide coated and uncoated tools, of the hot-rolled Pyromet® 31V alloy with hardness between 41.5 and 42.5 HRC. The nickel base alloy used consists essentially of the following components: 56.5% Ni, 22.5% Cr, 2,2% Ti, 0,04% C, 1,2% Al, 0.85% Nb and the rest of iron. Through the turning of this alloy we able to analyze the working mechanisms of wear on tools and evaluate the roughness provided on the cutting parameters used. The tests were performed on a CNC lathe machine using the coated carbide tool TNMG 160408-23 Class 1005 (ISO S15) and uncoated tools TNMG 160408-23 Class H13A (ISO S15). Cutting fluid was used so abundantly and cutting speeds were fixed in 75 and 90 m/min. to feed rates that ranged from 0.12, 0.15, 0.18 and 0.21 mm/rev. and cutting depth of 0.8mm. The results of the comparison between uncoated tools and coated ones presented a machined length of just 30% to the first in relation to the performance of the second. The coated tools has obtained its best result for both 75 and 90 m/min. with feed rate of 0.15 mm/rev. unlike the uncoated tool which obtained its better results to 0.12 mm/rev.

Sign in / Sign up

Export Citation Format

Share Document