MECHANICAL BEHAVIOR AND STRENGTH EVALUATION OF COMBINATION JOINTS USING RIVETS AND HIGH-STRENGTH BOLTS

2021 ◽  
Vol 77 (3) ◽  
pp. 489-508
Author(s):  
Takeshi HANJI ◽  
Shunya SUMI ◽  
Kazuo TATEISHI ◽  
Masaru SHIMIZU ◽  
Yasushi NAGASAKA ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
High Strength ◽  
Strength Evaluation

Development and Application of New Design Method by High-Strength Composite Material - Fusing of Optimum Strength Evaluation and Product Design

2013 ◽  
Vol 372 ◽  
pp. 17-20 ◽  
Author(s):  
Haruhiko Iida ◽  
Hidetoshi Sakamoto ◽  
Yoshifumi Ohbuchi
Keyword(s):  
Composite Material ◽  
Carbon Fiber ◽  
Product Design ◽  
Design Method ◽  
Target Material ◽  
High Strength ◽  
Fiber Glass ◽  
Strength Evaluation ◽  
Fiber Reinforced Materials ◽  
Manufacturing Methods

The purpose of this research is the development of new design method for integrating the optimum strength evaluation and the product design which can make the best use of material's characteristics obtained by the experiment and the analysis. Further we do design using high-strength composite material with this developed concept which is different from conventional design. First, to establish this design method of high-strength materials, we examined these materials characteristics and manufacturing methods and the commercialized products. As this research target material, we focus the fiber reinforced materials such as composite with carbon fiber, glass fiber and aramid fiber. Above all, we marked the carbon fiber which has the high specific tensile strength, wear resistance, heat conductivity and conductance. Here, we introduce the fundamental design concept which makes the best use of the design with enough strength.

Microstructures and Mechanical Behavior of Bulk Nanocrystalline γ–Ni–Fe Produced by a Mechanochemical Method

2002 ◽  
Vol 17 (5) ◽  
pp. 991-1001 ◽  
Author(s):  
X. Y. Qin ◽  
J. S. Lee ◽  
C. S. Lee
Keyword(s):  
Yield Strength ◽  
Mechanical Behavior ◽  
Light Emission ◽  
Hot Isostatic Pressing ◽  
Microstructural Analysis ◽  
High Strength ◽  
Compression Tests ◽  
Mechanochemical Method ◽  
Force Microscopy ◽  
Bulk Nanocrystalline

The microstructures and mechanical behavior of bulk nanocrystalline γ–Ni–xFe (n-Ni–Fe) with x = ∼19–21 wt%, synthesized by a mechanochemical method plus hot-isostatic pressing, were investigated using microstructural analysis [x-ray diffraction, energy-dispersive spectroscopy, light emission spectrum, atomic force microscopy (AFM), and optical microscopy (OM)], and mechanical (indentation and compression) tests, respectively. The results indicated that the yield strength (σ0.2) of n-Ni–Fe (d ∼ 33 nm) is about 13 times greater than that of conventional counterpart. The change of yield strength with grain size was basically in agreement with Hall–Petch relation in the size range (33–100 nm) investigated. OM observations demonstrated the existence of two sets of macroscopic bandlike deformation traces mostly orienting at 45–55° to the compression axis, while AFM observations revealed that these bandlike traces consist of ultrafine lines. The cause for high strength and the possible deformation mechanisms were discussed based on the characteristics of microstructures and deformation morphology of n-Ni–Fe.

Paradox of Strength and Ductility in Metals Processed Bysevere Plastic Deformation

2002 ◽  
Vol 17 (1) ◽  
pp. 5-8 ◽  
Author(s):  
R. Z. Valiev ◽  
I. V. Alexandrov ◽  
Y. T. Zhu ◽  
T. C. Lowe
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Yield Strength ◽  
Mechanical Behavior ◽  
High Strength ◽  
High Ductility ◽  
Elongation To Failure ◽  
Failure Ductility ◽  
Strength And Ductility

It is well known that plastic deformation induced by conventional forming methodssuch as rolling, drawing or extrusion can significantly increase the strength of metalsHowever, this increase is usually accompanied by a loss of ductility. For example, Fig.1 shows that with increasing plastic deformation, the yield strength of Cu and Almonotonically increases while their elongation to failure (ductility) decreases. Thesame trend is also true for other metals and alloys. Here we report an extraordinarycombination of high strength and high ductility produced in metals subject to severeplastic deformation (SPD). We believe that this unusual mechanical behavior is causedby the unique nanostructures generated by SPD processing. The combination ofultrafine grain size and high-density dislocations appears to enable deformation by newmechanisms. This work demonstrates the possibility of tailoring the microstructures ofmetals and alloys by SPD to obtain both high strength and high ductility. Materialswith such desirable mechanical properties are very attractive for advanced structuralapplications.

High strength biomedical Ti–13Mo–6Sn alloy: Processing routes, microstructural evolution and mechanical behavior

2019 ◽  
Vol 764 ◽  
pp. 138190 ◽  
Author(s):  
Mariana G. de Mello ◽  
Camilo A.F. Salvador ◽  
Leonardo Fanton ◽  
Rubens Caram
Keyword(s):  
Mechanical Behavior ◽  
Microstructural Evolution ◽  
High Strength
Sign in / Sign up

Export Citation Format

Share Document