FORMULATION AND EVALUATION OF LIDOCAINE HYDROCHLORIDE CHEWABLE TABLET

Objective: The objective of this study was to formulate and optimize a chewable formulation of lidocaine hydrochloride using a 32 factorial design for optimized the superdisintegrant concentration.Methods: Various concentrations of sodium starch glycolate (SSG) (13.33 mg, 26.66 mg, and 40 mg) of superdisintegrant and starch (50 mg, 83 mg, and 116.66 mg) were added in the formulation; nine formulations were prepared according to 32 factorial designs and evaluated. The responses were analyzed for analysis of variance using Design-Expert version 10 software. Statistical models were generated for each response parameter. The models were tested for significance. Procedure to manufacture chewable tablets by direct compression was established.Results: The results show that the presence of a superdisintegrant is desirable for chewable formulation. The best-optimized batch F7 found the batch having starch of amount 116.66 mg and SSG 13.33 mg. All the prepared batches of tablets were within the range. Optimized batch F7 showed drug content 102.46±0.0543, wetting time 18±1.7320, friability 0.65±0.0216, and drug release rate 99.97±0.0124% at the end of 30 min.Conclusion: It can be concluded that 32 full factorial design and statistical models can be successfully used to optimize the formulations, and it was concluded that the trial batch F7 is the optimized formulation which compiles official specifications of chewable tablets. The optimized batch was evaluated for thickness, weight variation, hardness, friability, drug dissolution, and stability study for 3 months. The similarity factor was calculated for comparison of dissolution profile before and after stability studies. After 30 min the drug release rate for batch F7 was 98.97% (Table 6). Hence, the results of stability studies reveal that the developed formulation has good stability.

Download Full-text

Effect of Channeling Agents on the Release Profile of Theophylline from METHOCEL K4M Based Matrix tablets

Dhaka University Journal of Pharmaceutical Sciences ◽

10.3329/dujps.v7i1.1214 ◽

1970 ◽

Vol 7 (1) ◽

pp. 27-32 ◽

Cited By ~ 4

Author(s):

Md Shaikhul Millat Ibn Razzak ◽

Ferdous Khan ◽

Md Ziaur Rahman Khan ◽

Kanij Fatema ◽

Muhammed Shahidul Islam ◽

...

Keyword(s):

Drug Release ◽

Release Rate ◽

Release Profile ◽

Matrix Tablets ◽

Drug Dissolution ◽

Release Mechanism ◽

Dissolution Profile ◽

Compression Process ◽

Low Viscosity ◽

Time Required

The present study was undertaken to investigate the effect of channeling agents on the release profile of Theophylline from METHOCEL K4M based matrix systems. Matrix tablets of Theophylline using METHOCEL K4M were prepared by direct compression process. METHOCEL K4M polymer is hydrophilic in nature. NaCl and PEG 1500 were used as channeling agents. Drug release study was evaluated for eight hours using USP 22 paddletype dissolution apparatus using distilled water as the dissolution medium. The release mechanisms were explored and explained with zero order, Higuchi and Korsmeyer equations. The release rate, extent and mechanisms were found to be governed by channeling agent type and content. Higher channeling agent content (42.49%) in the matrix increased the rate and extent of the drug release because of increased porosity in the tablet matrices, at lower channeling agent (19.76%) level, the rate and extent of drug release was decreased and in absence of channeling agents these were least. NaCl ensures maximum release of drug from low viscosity grade METHOCEL K4M than PEG 1500 when other parameters were kept constant. It was found that type and amount of channeling agent significantly affect the time required for 50% of drug release (T50%), percentage drug release at 8 hours, release rate constant (K) and diffusion exponent (n). Kinetic modeling of dissolution profiles revealed drug release mechanism ranges from diffusion controlled or Fickian transport to anomalous type or non-Fickian transport, which was mainly dependent on the presence of type and amount of channeling agent. These studies indicate that the proper balance between a matrix forming agent and a channeling agent can produce a drug dissolution profile similar to a theoretical dissolution profile.Key words: Channeling agent, Theophylline, Release Profile, Methocel K4MDOI = 10.3329/dujps.v7i1.1214Dhaka Univ. J. Pharm. Sci. 7(1): 27-32, 2008 (June)

Download Full-text

Liqui-Tablet: the Innovative Oral Dosage Form Using the Newly Developed Liqui-Mass Technology

AAPS PharmSciTech ◽

10.1208/s12249-021-01943-w ◽

2021 ◽

Vol 22 (3) ◽

Author(s):

Matthew Lam ◽

Kofi Asare-Addo ◽

Ali Nokhodchi

Keyword(s):

Drug Release ◽

Release Rate ◽

Dosage Form ◽

Oral Dosage ◽

Dissolution Profile ◽

Drug Release Rate ◽

Accelerated Stability ◽

Micro Tomography ◽

Distribution Of Components ◽

Tablet Dosage

AbstractIn this study, an attempt was made to produce Liqui-Tablets for the first time. This was carried out through the compaction of naproxen Liqui-Pellets. The incentive to convert the novel Liqui-Pellet into Liqui-Tablet was due to the array of inherent advantages of the popular and preferred tablet dosage form. The study showed that naproxen Liqui-Tablet could be successfully produced and the rapid drug release rate (100% drug release ~ 20 min) could be achieved under pH 1.2, where naproxen is insoluble. It was observed that the different pH of the dissolution medium affected the trend of drug release from formulations with varying amounts of liquid vehicle. The order of the fastest drug-releasing formulations was different depending on the pH used. The presence of Neusilin US2 showed considerable enhancement in the drug release rate as well as improving Liqui-Tablet robustness and hardness. Furthermore, images from X-ray micro-tomography displayed a uniform distribution of components in the Liqui-Tablet. The accelerated stability studies showed acceptable stability in terms of dissolution profile.

Download Full-text

Polymer Distribution and Mechanism Conversion in Multiple Media of Phase-Separated Controlled-Release Film-Coating

Pharmaceutics ◽

10.3390/pharmaceutics11020080 ◽

2019 ◽

Vol 11 (2) ◽

pp. 80 ◽

Cited By ~ 4

Author(s):

Lu Chen ◽

Guobao Yang ◽

Xiaoyang Chu ◽

Chunhong Gao ◽

Yuli Wang ◽

...

Keyword(s):

Controlled Release ◽

Drug Release ◽

Release Rate ◽

Water Soluble ◽

Drug Dissolution ◽

Acetate Buffer ◽

Drug Solubility ◽

Drug Release Rate ◽

The Media ◽

Multiple Media

Phase-separated films of water-insoluble ethyl cellulose (EC) and water-soluble hydroxypropyl cellulose (HPC) can be utilized to tailor drug release from coated pellets. In the present study, the effects of HPC levels and the pH, type, ionic strength and osmolarity of the media on the release profiles of soluble metoprolol succinates from the EC/HPC-coated pellets were investigated, and the differences in drug-release kinetics in multiple media were further elucidated through the HPC leaching and swelling kinetics of the pellets, morphology (SEM) and water uptake of the free films and the interaction between the coating polymers and the media compositions. Interestingly, the drug release rate from the pellets in different media was not in agreement with the drug solubility which have a positive correlation with the drug dissolution rate based on Noyes–Whitney equation law. In particular, the drug release rate in acetate buffer at pH 4.5 was faster than that in other media despite the solubility of drug was relatively lower, regardless of the HPC levels. It may be attributed to the mutual effect between the EC and acetate buffer, which improved the permeability of the film. In contrast, the release of drug in HCl solution was dependent on the HPC levels. Increasing the levels of HPC increased the effects of hydrogen ions on the polymer of HPC, which resulted in a lower viscosity and strength of the gel, forming the larger size of pores in polymer films, thus increasing the drug diffused from the coating film. Further findings in phosphate buffer showed a reduction in the drug release compared to that in other media, which was only sensitive to the osmolarity rather than the HPC level and pH of the buffer. Additionally, a mathematical theory was used to better explain and understand the experimentally measured different drug release patterns. In summary, the study revealed that the effects of the media overcompensated that of the drug solubility to some extent for controlled-release of the coating polymers, and the drug release mechanism in multiple media depend on EC and HPC rather than on HPC alone, which may have a potential to facilitate the optimization of ideally film-coated formulations.

Download Full-text

Formulation and Evaluation of Nelfinavir Extended Release Trilayer Matrix Tablets by Design of Experiment

International Journal of Pharmaceutical Sciences and Nanotechnology ◽

10.37285/ijpsn.2018.11.5.6 ◽

2018 ◽

Vol 11 (5) ◽

pp. 4259-4268

Author(s):

Nirmala Rangu ◽

Gande Suresh

Keyword(s):

Controlled Release ◽

Drug Release ◽

Hydroxypropyl Methylcellulose ◽

Magnesium Stearate ◽

Zero Order ◽

Matrix Tablets ◽

Drug Dissolution ◽

Crystalline Cellulose ◽

Dissolution Profile ◽

Release Formulation

The present study was aimed to develop once-daily controlled release trilayer matrix tablets of nelfinavir to achieve zero-order drug release for sustained plasma concentration. Nelfinavir trilayer matrix tablets were prepared by direct compression method and consisted of middle active layer with different grades of hydroxypropyl methylcellulose (HPMC), PVP (Polyvinyl Pyrrolidine) K-30 and MCC (Micro Crystalline Cellulose). Barrier layers were prepared with Polyox WSR-303, Xanthan gum, microcrystalline cellulose and magnesium stearate. Based on the evaluation parameters, drug dissolution profile and release drug kinetics DF8 were found to be optimized formulation. The developed drug delivery system provided prolonged drug release rates over a period of 24 h. The release profile of the optimized formulation (DF8) was described by the zero-order and best fitted to Higuchi model. FT-IR studies confirmed that there were no chemical interactions between drug and excipients used in the formulation. These results indicate that the approach used could lead to a successful development of a controlled release formulation of nelfinavir in the management of AIDS.

Download Full-text

Formulation Development and Characterization of controlled release core in cup matrix tablets of venlafaxine HCl

Current Drug Therapy ◽

10.2174/1574885515666200331104440 ◽

2020 ◽

Vol 15 ◽

Author(s):

Balaji Maddiboyina ◽

Vikas Jhawat ◽

Gandhi Sivaraman ◽

Om Prakash Sunnapu ◽

Ramya Krishna Nakkala ◽

...

Keyword(s):

Controlled Release ◽

Drug Release ◽

Release Rate ◽

Zero Order ◽

Water Soluble ◽

Matrix Tablets ◽

Drug Dissolution ◽

Crystalline Cellulose ◽

Hydrophobic Polymers

Background: Venlafaxine HCl is a selective serotonin reuptake inhibitor which is given in the treatment of depression. The delivery of the drug at a controlled rate can be of great importance for prolonged effect. Objective: The objective was to prepare and optimize the controlled release core in cup matrix tablet of venlafaxine HCl using the combination of hydrophilic and hydrophobic polymers to prolong the effect with rate controlled drug release. Methods: The controlled release core in cup matrix tablets of venlafaxine HCl were prepared using HPMC K5, K4, K15, HCO, IPA, aerosol, magnesium sterate, hydrogenated castor oil and micro crystalline cellulose PVOK-900 using wet granulation technique. Total ten formulations with varying concentrations of polymers were prepared and evaluated for different physicochemical parameters such FTIR analysis for drug identification, In-vitro drug dissolution study was performed to evaluate the amount of drug release in 24 hrs, drug release kinetics study was performed to fit the data in zero order, first order, Hixson–crowell and Higuchi equation to determine the mechanism of drug release and stability studies for 3 months as observed. Results: The results of hardness, thickness, weight variation, friability and drug content study were in acceptable range for all formulations. Based on the In vitro dissolution profile, formulation F-9 was considered to be the optimized extending the release of 98.32% of drug up to 24 hrs. The data fitting study showed that the optimized formulation followed the zero order release rate kinetics and also compared with innovator product (flavix XR) showed better drug release profile. Conclusion: The core-in-cup technology has a potential to control the release rate of freely water soluble drugs for single administration per day by optimization with combined use of hydrophilic and hydrophobic polymers.

Download Full-text

Microorganism-based monodisperse microcapsules: encapsulation of the fungicide tebuconazole and its controlled release properties

RSC Advances ◽

10.1039/c5ra01629k ◽

2015 ◽

Vol 5 (32) ◽

pp. 25164-25170 ◽

Cited By ~ 6

Author(s):

Bo Zhang ◽

Teng Zhang ◽

Quanxi Wang ◽

Tianrui Ren

Keyword(s):

Controlled Release ◽

Powdery Mildew ◽

Drug Release ◽

Release Rate ◽

Drug Release Rate ◽

Burst Effect ◽

Initial Burst ◽

Release System ◽

Controlled Release System ◽

Monodisperse Microcapsules

A controlled release system was prepared, it based on UF modified PCC cells in which TEB are loaded into cells. It can control the drug release rate, depress the initial “burst effect”, and was efficacious in controlling wheat powdery mildew.

Download Full-text