scholarly journals Experimental Method for Wind Tunnel Tests to Simulate Turbulent Flow on the Roof of High-speed Trains

2012 ◽  
Vol 53 (3) ◽  
pp. 167-172 ◽  
Author(s):  
Takehisa TAKAISHI ◽  
Mitsuru IKEDA
Keyword(s):  
Wind Tunnel ◽  
Turbulent Flow ◽  
Experimental Method ◽  
High Speed ◽  
Wind Tunnel Tests ◽  
High Speed Trains

The Effect of Cross-Winds on Trains

1981 ◽  
Vol 103 (1) ◽  
pp. 170-178 ◽  
Author(s):  
R. K. Cooper
Keyword(s):  
Wind Tunnel ◽  
Model Experiment ◽  
High Speed ◽  
Wind Tunnel Tests ◽  
Turbulent Wind ◽  
Wind Speeds ◽  
High Speed Trains ◽  
Low Mass

Low mass, high speed trains may be in danger of being overturned by strong crosswinds. This paper examines the aerodynamic data required to estimate overturning wind speeds. The results of wind tunnel tests and a moving model experiment, including the effect of the turbulent wind, are described.

scholarly journals Structure Clearance Design in Wind Tunnel Tests with Implications for Aerodynamic Drag of High-Speed Trains

2021 ◽  
Author(s):  
Zhixiang Huang ◽  
Hanjie Huang ◽  
Weiping Zeng ◽  
Li Chen ◽  
Renyu Zhu
Keyword(s):  
Reynolds Number ◽  
Wind Tunnel ◽  
Drag Coefficient ◽  
Distribution Pattern ◽  
High Speed ◽  
Aerodynamic Drag ◽  
High Speed Train ◽  
Wind Tunnel Tests ◽  
High Speed Trains

Abstract The influences of vestibule diaphragm gap, wheel-rail clearance, and strut-plate gap on the aerodynamic drag of a 1/8th-scale high-speed train model were investigated in an 8 m×6 m wind tunnel. The Reynolds number was set to 2.2×106 based on train height. It was found that the variation of the vestibule diaphragm gap changed the aerodynamic drag distribution pattern of each car; the drag coefficient of the head and middle cars might change as high as 45%; however, the change in the drag coefficient of the total train was very small. The effects of the strut-plate gap on the aerodynamic drag of each car and the total train were small. The effect of the wheel-rail clearance on the drag of the head car was not significant. It was suggested that the vestibule diaphragm gap, strut-plate gap and wheel-rail clearance of the 1:8 scale high-speed train model should not be greater than 11, 10, and 9 mm, respectively.

Numerical Simulation of Flowfield around High Speed Trains Passing by each other at the same Speed

2011 ◽  
Vol 97-98 ◽  
pp. 698-701
Author(s):  
Ming Lu Zhang ◽  
Yi Ren Yang ◽  
Li Lu ◽  
Chen Guang Fan
Keyword(s):  
Numerical Simulation ◽  
Wind Tunnel ◽  
Flow Field ◽  
Point Source ◽  
High Speed ◽  
Stokes Equations ◽  
Field Structure ◽  
Vehicle Speed ◽  
Mesh Method ◽  
High Speed Trains

Large eddy simulation (LES) was made to solve the flow around two simplified CRH2 high speed trains passing by each other at the same speed base on the finite volume method and dynamic layering mesh method and three dimensional incompressible Navier-Stokes equations. Wind tunnel experimental method of resting train with relative flowing air and dynamic mesh method of moving train were compared. The results of numerical simulation show that the flow field structure around train is completely different between wind tunnel experiment and factual running. Two opposite moving couple of point source and point sink constitute the whole flow field structure during the high speed trains passing by each other. All of streamlines originate from point source (nose) and finish with the closer point sink (tail). The flow field structure around train is similar with different vehicle speed.

A wind-tunnel methodology for assessing the slipstream of high-speed trains

2017 ◽  
Vol 166 ◽  
pp. 1-19 ◽  
Author(s):  
J.R. Bell ◽  
D. Burton ◽  
M.C. Thompson ◽  
A.H. Herbst ◽  
J. Sheridan
Keyword(s):  
Wind Tunnel ◽  
High Speed ◽  
High Speed Trains

scholarly journals Geometric Effects Analysis and Verification of V-Shaped Support Interference on Blended Wing Body Aircraft

2020 ◽  
Vol 10 (5) ◽  
pp. 1596
Author(s):  
Xin Xu ◽  
Qiang Li ◽  
Dawei Liu ◽  
Keming Cheng ◽  
Dehua Chen
Keyword(s):  
Wind Tunnel ◽  
High Speed ◽  
Pitching Moment ◽  
Straight Section ◽  
Test Results ◽  
Wind Tunnel Tests ◽  
Blended Wing Body ◽  
Support Interference ◽  
Geometric Effects ◽  
Good Agreement

A special V-shaped support for blended wing body aircraft was designed and applied in high-speed wind tunnel tests. In order to reduce the support interference and explore the design criteria of the V-shaped support, interference characteristics and geometric parameter effects of V-shaped support on blended wing body aircraft were numerically studied. According to the numerical results, the corresponding dummy V-shaped supports were designed and manufactured, and verification tests was conducted in a 2.4 m × 2.4 m transonic wind tunnel. The test results were in good agreement with the numerical simulation. Results indicated that pitching moment of blended wing body aircraft is quite sensitive to the V-shaped support geometric parameters, and the influence of the inflection angle is the most serious. To minimize the pitching moment interference, the straight-section diameter and inflection angle should be increased while the straight-section length should be shortened. The results could be used to design special V-shaped support for blended wing body aircraft in wind tunnel tests, reduce support interference, and improve the accuracy of test results.

Preparation and execution of the NICETRIP low- and high-speed wind tunnel tests

2016 ◽  
Vol 7 (2) ◽  
pp. 167-184
Author(s):  
O. Schneider ◽  
M. Przybilla ◽  
E. Brehl ◽  
H. Mainz ◽  
Y. Govers ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
High Speed ◽  
Wind Tunnel Tests
Sign in / Sign up

Export Citation Format

Share Document