scholarly journals Study of convection heat transfer enhancement inside lid driven cavity utilizing fins and nanofluid

2017 ◽  
Vol 21 (6 Part A) ◽  
pp. 2431-2442
Author(s):  
Arash Lavasani ◽  
Mousa Farhadi ◽  
Darzi Rabienataj
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Richardson Number ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Thermal Conductivity Ratio ◽  
Convection Flow ◽  
Driven Cavity ◽  
Ratio Change ◽  
Hot Surface

In the present study, the effect of suspension of nanoparticle on mixed convection flow is investigated numerically in lid driven cavity with fins on its hot surface. Study is carried out for Richardson numbers ranging from 0.1 to 10, fin(s) height ratio change from 0.05 to 0.15 and volume fraction of nanoparticles from 0 to 0.03, respectively. The thermal conductivity ratio (kfin/kf) is equal to 330 and Grashof number is assumed to be constant (104) so that the Richardson numbers changes with Reynolds number. Results show that the heat transfer enhances by using nanofluid for all studied Richardson numbers. Adding fins on hot wall has different effects on heat transfer depend to Richardson number and height of fins. Use of low height fin in flow with high Richardson number enhances the heat transfer rate while by increasing the height of fin the heat transfer reduces even lower than it for pure fluid. The overall enhancement in Nusselt number by adding 3% nanoparticles and 3 fins is 54% at Ri=10. They cause reduction of Nusselt Number by 25% at Ri=0.1. Higher fins decrease the heat transfer due to blocking fluid at corners of fins.

Numerical study of the fin effect on mixed convection heat transfer in a lid-driven cavity

2010 ◽  
Vol 225 (2) ◽  
pp. 397-406 ◽  
Author(s):  
A A R Darzi ◽  
M Farhadi ◽  
K Sedighi
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Richardson Number ◽  
Numerical Study ◽  
Convection Heat Transfer ◽  
Thermal Conductivity Ratio ◽  
Driven Cavity ◽  
Ratio Change ◽  
Vertical Walls ◽  
Energy Equations

In this study, the mixed convective heat transfer in a lid-driven cavity was investigated numerically. The finite volume discritization method was used to solve the momentum and energy equations by using the classic Boussinesq incompressible approximation. The cavity vertical walls are insulated whereas the bottom (hot wall) and top (cold wall) surface are maintained at a uniform temperature and fins are located on bottom wall. The effect of fin numbers over the flow field and heat transfer was investigated at various Richardson numbers. Study was carried out for Richardson numbers ranging from 0.01 to 10, fin numbers between 1 and 7, fin height ratio change from 0.05 to 0.3, and thermal conductivity ratio (fin to fluid) from 10 to 104, respectively. The results are presented in the form of streamlines, temperature contours, and Nusselt number distributions. The results show that the Nusselt number increases when the number of fin and fin height decrease. In addition, in all cases an increasing Richardson number caused increasing the relative Nusselt number ( Nu / Nu0). The heat transfer enhancement was observed at low fin numbers (1 and 3) and high Richardson number in comparison with the cavity without fins.

Effect of Nanofluid on Heat Transfer Enhancement for Mixed Convection Flow Over a Corrugated Surface

2020 ◽  
Vol 45 (4) ◽  
pp. 373-383
Author(s):  
Nepal Chandra Roy ◽  
Sadia Siddiqa
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Local Nusselt Number ◽  
Richardson Number ◽  
Thermal Boundary Layer ◽  
Volume Fraction ◽  
Convection Flow ◽  
Mixed Convection Flow

AbstractA mathematical model for mixed convection flow of a nanofluid along a vertical wavy surface has been studied. Numerical results reveal the effects of the volume fraction of nanoparticles, the axial distribution, the Richardson number, and the amplitude/wavelength ratio on the heat transfer of Al2O3-water nanofluid. By increasing the volume fraction of nanoparticles, the local Nusselt number and the thermal boundary layer increases significantly. In case of \mathrm{Ri}=1.0, the inclusion of 2 % and 5 % nanoparticles in the pure fluid augments the local Nusselt number, measured at the axial position 6.0, by 6.6 % and 16.3 % for a flat plate and by 5.9 % and 14.5 %, and 5.4 % and 13.3 % for the wavy surfaces with an amplitude/wavelength ratio of 0.1 and 0.2, respectively. However, when the Richardson number is increased, the local Nusselt number is found to increase but the thermal boundary layer decreases. For small values of the amplitude/wavelength ratio, the two harmonics pattern of the energy field cannot be detected by the local Nusselt number curve, however the isotherms clearly demonstrate this characteristic. The pressure leads to the first harmonic, and the buoyancy, diffusion, and inertia forces produce the second harmonic.

A Numerical Investigation of Laminar Mixed Convection Flow and Heat Transfer in a Lid Driven Cavity with Two Cylinders

2015 ◽  
Vol 789-790 ◽  
pp. 282-286 ◽  
Author(s):  
Khalil Khanafer ◽  
M. El Haj Assad
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Richardson Number ◽  
Average Nusselt Number ◽  
Convection Flow ◽  
Mixed Convection Flow ◽  
Driven Cavity ◽  
Flow And Heat Transfer ◽  
The Impact

Mixed convection flow and heat transfer characteristics in a lid-driven cavity with two isothermally heated circular cylinders inside are studied numerically using a finite element formulation based on the Galerkin method of weighted residuals. The top lid of the cavity is moving rightwards with a constant speed. The two cylinders are maintained at an isothermal hot temperature, while the walls of the cavity are maintained at a cold temperature. Comparisons of streamlines, isotherms and average Nusselt number are presented to show the impact of the Richardson number, non-dimensional radius of the cylinder, and the location of the cylinders on the transport phenomena within the cavity. The results of this investigation show that the presence of the cylinders results in an increase in the average Nusselt number compared with a case with no cylinder. The average Nusselt number increases with an increase in the Richardson number for all non-dimensional radius of the cylinder studied in this work. It is seen that changing the boundary condition on one of the cylinders from isothermal to adiabatic has minimal effect on the average Nusselt number around the walls of the cavity.

scholarly journals Mixed convection of functionalized DWCNT-water nanofluid in baffled lid-driven cavities

2018 ◽  
Vol 22 (6 Part A) ◽  
pp. 2503-2514 ◽  
Author(s):  
Esfe Hemmat ◽  
Arani Abbasian ◽  
Wei-Mon Yan ◽  
Alireza Aghaie ◽  
Masoud Afrand ◽  
...  
Keyword(s):  
Nusselt Number ◽  
Mixed Convection ◽  
Richardson Number ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Minimum Length ◽  
Convection Flow ◽  
Flow And Heat Transfer ◽  
Inclination Angles ◽  
Nanoparticles Volume Fraction

The present study aims to evaluate the mixed convection flow and heat transfer of functionalized DWCNT/water nanofluids with variable properties in a cavity having hot baffles. The investigation is performed at different nanoparticles volume fraction including 0, 0.0002, 0.001, 0.002, and 0.004, Richardson numbers ranging from 0.01 to 100, inclination angles ranging from 0 to 60? and at constant Grashof number of 104. The results presented as streamlines and isotherms plot and Nusselt number diagrams. According to the finding with increasing nanoparticles volume fraction and distance between the left hot baffles of nanoparticles average Nusselt number enhances for all considered Richardson numbers and cavity inclination angles. Also with increasing Richardson number, the rate of changes of average Nusselt number increase with increasing distance between the left hot baffles. For example, at Richardson number of 0.01, by increasing L1 from 0.4 to 0.6, the average Nusselt number increases 7%; while for similar situation at Richardson number of 0.1, 1.0, and 10, the average Nusselt number increases, respectively, 17%, 24%, and 26%. At all Richardson numbers, the maximum value of average Nusselt number is achieved for a minimum length of left baffles. <br><br><font color="red"><b> This article has been corrected. Link to the correction <u><a href="http://dx.doi.org/10.2298/TSCI190203032E">10.2298/TSCI190203032E</a><u></b></font>

Augmentation of Pure Mixed Convection Heat Transfer in a Non-newtonian Power-law Fluid Filled Lid-driven Trapezoidal Cavity with Double Rotating Cylinders

2021 ◽  
Author(s):  
Hasib Ahmed Prince ◽  
Didarul Ahasan Redwan ◽  
Enamul Hasan Rozin ◽  
Sudipta Saha ◽  
Mohammad Arif Hasan Mamun
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Numerical Investigation ◽  
Power Law ◽  
Convection Heat Transfer ◽  
Cavity Surface ◽  
Rotating Cylinders ◽  
Power Law Fluid ◽  
Driven Cavity

Abstract In this study, a numerical investigation on mixed convection inside a trapezoidal cavity with a pair of rotating cylinders has been conducted. Three different power-law fluid indexes (n = 1.4, 1.0, and 0.6) have been considered to model different sets of non-Newtonian fluids. Four separate cases are considered dependent on the rotation orientation of the cylinders within the cavity. In the first two cases, the cylinders rotate in the same direction, i.e., both counter-clockwise (CCW), and both clockwise (CW), whereas, in the other two cases, cylinders rotate in opposite directions (CW-CCW and CCW-CW). Simulations have been carried out over a broad range of Reynolds number (from 0.5 to 500) and angular speeds (a dimensionless value from 0 to 10). The average Nusselt number values at the isothermal hot inclined cavity surface are determined to evaluate heat transfer performance in various circumstances. Streamlines and isotherm contours are also plotted for better understandings of the effects of different cases for various parameters on thermal and fluid flow fields. It is found that the Nusselt number varies non-linearly with different angular speeds of the cylinders. The combined effect of the mixing induced by cylinder rotation and viscosity characteristics of the fluid dictates the heat transfer in the system. Predictions from the numerical investigation provide insights onto the sets of key parametric configuration that have dominant influence on the thermal performance of lid driven cavity with double rotating cylinders.

Numerical simulation of water/alumina nanofluid mixed convection in square lid-driven cavity

2019 ◽  
Vol 30 (5) ◽  
pp. 2781-2807
Author(s):  
Davood Toghraie ◽  
Ehsan Shirani
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Richardson Number ◽  
Hartmann Number ◽  
Two Phase ◽  
Content Type ◽  
Driven Cavity

Purpose The purpose of this paper is to investigate the mixed convection of a two-phase water–aluminum oxide nanofluid in a cavity under a uniform magnetic field. Design/methodology/approach The upper wall of the cavity is cold and the lower wall is warm. The effects of different values of Richardson number, Hartmann number, cavitation length and solid nanoparticles concentration on the flow and temperature field and heat transfer rate were evaluated. In this paper, the heat flux was assumed to be constant of 10 (W/m2) and the Reynolds number was assumed to be constant of 300 and the Hartmann number and the volume fraction of solid nanoparticles varied from 0 to 60 and 0 to 0.06, respectively. The Richardson number was considered to be 0.1, 1 and 5. Aspect ratios were 1, 1.5 and 2. Findings Comparison of the results of this paper with the results of the numerical and experimental studies of other researchers showed a good correlation. The results were presented in the form of velocity and temperature profiles, stream and isotherm lines and Nusselt numbers. The results showed that by increasing the Hartmann number, the heat transfer rate decreases. An increase from 0 to 20 in Hartmann number results in a 20 per cent decrease in Nusselt numbers, and by increasing the Hartmann number from 20 to 40, a 16 per cent decrease is observed in Nusselt number. Accordingly, it is inferred that by increasing the Hartmann number, the reduction in the Nusselt number is decreased. As the Richardson number increased, the heat transfer rate and, consequently, the Nusselt number increased. Therefore, an increase in the Richardson number results in an increase of the Nusselt number, that is, an increase in Richardson number from 0.1 to 1 and from 1 to 5 results in 37 and 47 per cent increase in Nusselt number, respectively. Originality/value Even though there have been numerous investigations conducted on convection in cavities under various configurations and boundary conditions, relatively few studies are conducted for the case of nanofluid mixed convection in square lid-driven cavity under the effect of magnetic field using two-phase model.

scholarly journals ISPH simulations of natural convection from heated rotating paddles on a circular cylinder inside a cross-shaped cavity filled with a nanofluid

2020 ◽  
Author(s):  
Abdelraheem Mahmoud Aly ◽  
Ehab Mahmoud
Keyword(s):  
Heat Transfer ◽  
Porous Media ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Natural Convection ◽  
Circular Cylinder ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Heterogeneous Porous Media ◽  
Convection Flow

The numerical simulations of the uniform circular rotation of paddles on circular cylinder results natural convection flow of Al2O3-water in a cross-shaped porous cavity were performed by incompressible representation of smoothed particle hydrodynamics entitled ISPH method. The two vertical area of a cross-shaped cavity is saturated with homogeneous porous media and the whole horizontal area of a cross-shaped cavity is saturated with heterogeneous porous media. The inner paddles on the circular cylinder are rotating around their center by a uniform circular velocity. The whole embedded body of paddles on a circular cylinder has temperature Th. The wall-sides of a cross-shaped cavity are positioned at a temperature Tc. The current geometry can be applied in analysis and understanding the thermophysical behaviors of the electronic motors. The angular velocity is taken as ! = 7:15 and consequently the natural convection case is only considered due to the low speed of inner rotating shape. The performed simulations are represented in the graphical for the temperature distributions, velocity fields and tabular forms for average Nusselt number. The results revealed that an augmentation on paddle length rises the heat transfer and speed of fluid flow inside a cross shaped cavity. Also, an incrementation on Rayleigh number augments the heat transfer and speed of the fluid flow inside a cross-shaped cavity. The fluid flow is circulated only around the rotating inner shape when Darcy parameter decreases to Da = 105. Average Nusselt number Nu enhances by an increment on the paddle lengths and nanoparticles volume fraction

scholarly journals Prediction of Natural Convection Heat Transfer Phenomena of Nanofluids in Corrugated Annulus

2020 ◽  
Author(s):  
Sattar Aljobair ◽  
Akeel Abdullah Mohammed ◽  
Israa Alesbe
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Outer Cylinder ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Convection Heat

Abstract The natural convection heat transfer and fluid flow characteristic of water based Al2O3 nano-fluids in a symmetrical and unsymmetrical corrugated annulus enclosure has been studied numerically using CFD. The inner cylinder is heated isothermally while the outer cylinder is kept constant cold temperature. The study includes eight models of corrugated annulus enclosure with constant aspect ratio of 1.5. The governing equations of fluid motion and heat transfer are solved using stream-vorticity formulation in curvilinear coordinates. The range of solid volume fractions of nanoparticles extends from PHI=0 to 0.25, and Rayleigh number varies from 104 to 107. Streamlines, isotherms, local and average Nusselt number of inner and outer cylinder has been investigated in this study. Sixty-four correlations have been deduced for the average Nusselt number for the inner and outer cylinders as a function of Rayleigh number have been deduced for eight models and five values of volume fraction of nano particles with an accuracy range 6-12 %. The results show that, the average heat transfer rate increases significantly as particle volume fraction and Rayleigh number increase. Also, increase the number of undulations in unsymmetrical annuli reduces the heat transfer rates which remain higher than that in symmetrical annuli. There is no remarkable change in isotherms contour with increase of volume fraction of nanofluid.

Numerical Study on Conjugated Laminar Mixed Convection of Alumina/Water Nanofluid Flow, Heat Transfer, and Entropy Generation Within a Tube-on-Sheet Flat Plate Solar Collector

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Mohammad Charjouei Moghadam ◽  
Mojtaba Edalatpour ◽  
Juan P. Solano
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Entropy Generation ◽  
Solar Collector ◽  
Richardson Number ◽  
Volume Concentration ◽  
Volume Fraction ◽  
Flat Plate Solar Collector

In this research, an inclined three-dimensional nanofluid-based tube-on-sheet flat plate solar collector (FPSC) working under laminar conjugated mixed convection heat transfer is numerically modeled. The working fluid is selected to be alumina/water (Al2O3/water) and results from heat transfer, entropy generation, and pressure drop points of view are being presented for various prominent parameters, namely volume fraction, nanoparticles diameter, Richardson and Reynolds numbers. According to the simulations, Nusselt number decreases as the Richardson number or volume fraction of the nanofluid rises, whereas heat transfer coefficient experiences an augmentation when volume concentration and the Richardson number surge. Also, data reveal that total entropy generation rate of the system declines when the alumina/water nanofluid is utilized inside the system as the volume fraction or the Richardson number increases. Additionally, it is found that increasing the nanoparticle volume concentration or the Richardson number diminishes the pressure drop considerably, whereas friction factor substantially proliferates as the Richardson number or volume fraction rises. Eventually, employment of larger alumina nanoparticles mean diameter eventuates in providing lower Nusselt number and apparent friction factor while it increases the pressure drop and heat transfer coefficient. Finally, comparing the efficiency of the presented FPSC design with those available in the literature shows a superior performance by the present design with its maximum occurring at 2 vol %.

Laminar Mixed Convection of Non-Newtonian Nanofluids Flowing Vertically Upward Across a Confined Circular Cylinder

2018 ◽  
Vol 10 (4) ◽  
Author(s):  
Abhipsit Kumar Singh ◽  
Nanda Kishore
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Circular Cylinder ◽  
Mixed Convection ◽  
Richardson Number ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Numerical Results ◽  
Total Drag ◽  
Drag Coefficients

Numerical results on laminar mixed convective heat transfer phenomenon between a confined circular cylinder and shear-thinning type nanofluids are presented. The cylinder is placed horizontally in a confined channel through which nanofluids flow vertically upward. The effect of buoyancy is same as the direction of the flow. Because of existence of mixed convection, governing continuity, momentum, and energy equations are simultaneously solved within the limitations of Boussinesq approximation. The ranges of parameters considered are: volume fraction of nanoparticles, ϕ = 0.005–0.045; Reynolds number, Re = 1–40; Richardson number, Ri = 0–40; and confinement ratio of circular cylinder, λ = 0.0625–0.5. Finally, the effects of these parameters on the streamlines, isotherm contours, individual and total drag coefficients, and local and average Nusselt numbers are thoroughly delineated. The individual and total drag coefficients decrease with the increasing both ϕ and Re; and/or with the decreasing both Ri and λ. The rate of heat transfer increases with the increasing Re, ϕ, Ri, and λ; however, at Re = 30–40, when ϕ > 0.005 and Ri < 2, the average Nusselt number decreases with the increasing Richardson number. Finally, correlations for the total drag coefficient and average Nusselt number are proposed as functions of pertinent dimensionless parameters on the basis of present numerical results.

Sign in / Sign up

Export Citation Format

Share Document