scholarly journals Thermal performance prediction of heat pipe with TiO2 nanofluids using RSM

2021 ◽  
pp. 199-199
Author(s):  
Lakshmi Reddy ◽  
Srinivasa Bayyapureddy Reddy ◽  
Kakumani Govindarajulu
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Thermal Resistance ◽  
Transfer Coefficient ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Tilt Angle ◽  
Heat Load ◽  
Maximum Heat ◽  
Maximum Heat Transfer

Heat pipe is a two phase heat transfer device with high effective thermal conductivity and transfer huge amount of heat with minimum temperature gradient in between evaporator and condenser section. This paper objective is to predict the thermal performance in terms of thermal resistance (R) and heat transfer coefficient (h) of screen mesh wick heat pipe with DI water-TiO2 as working fluid. The input process parameters of heat pipe such as heat load (Q), tilt angle (?) and concentration of nanofluid (?) were modeled and optimized by utilizing Response Surface Methodology (RSM) with MiniTab-17 software to attain minimum thermal resistance and maximum heat transfer coefficient. The minimum thermal resistance of 0.1764 0C/W and maximum heat transfer coefficient of 1411.52 W/m2 0C was obtained under the optimized conditions of 200 W heat load, 57.20 tilt angle and 0.159 vol. % concentration of nano-fluid.

Performance of a Flexible Evaporator for Loop Heat Pipe Applications

2008 ◽  
Author(s):  
Mukta S. Limaye ◽  
James F. Klausner
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Heat Pipe ◽  
Heat Fluxes ◽  
Loop Heat Pipe ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Maximum Heat Flux

A flat and flexible evaporator, which conforms to contoured surfaces, has been developed for loop heat pipe applications. A loop heat pipe (LHP) is a passive, two phase heat transfer device that uses a porous membrane in the evaporator to circulate fluid. A number of flexible membranes have been tested as evaporator wicks that have a length of 12.7 cm and heated area of 50.6 cm2. For cellulose, polyethylene, and blotting paper membranes, maximum heat fluxes of 0.43, 1.5 and 2.9 W/cm2 have been observed, respectively. The maximum heat transfer coefficients measured for these membranes are 551, 876, and 2100 W/m2-K, respectively. The best performance was observed by a membrane made of a fibrous cotton matrix, typically used as gauze. This material has a large pore size and high wettability with water. When tested in a rigid, brass evaporator, the maximum heat flux observed is 5.95 W/cm2, and the maximum heat transfer coefficient is 2865 W/m2-K. A flexible evaporator is fabricated using a heat sealable, flexible barrier pouch, and the cotton matrix membrane is sealed inside. The maximum measured heat flux for the flexible evaporator is 3.2 W/cm2 and maximum measured heat transfer coefficient is 1165 W/m2-K. The observed reduction in heat transfer as compared to the rigid evaporator is due to the poor contact between the evaporator and membrane. It is concluded that for the flexible evaporator membranes considered, the heat transfer mechanism is boiling and the maximum heat flux is limited by the wicking rate of the membrane. For a given membrane, the wicking rate increases with a reduction in the wicking length and decreases with an increasing rate of evaporation. To further improve the performance of the flexible evaporator, it is necessary to ensure efficient vapor removal from the evaporator as well as maintaining good contact between the membrane and the evaporator surface.

Thermal Performance of a Compact Loop Heat Pipe with Silver-Water Nanofluid

2016 ◽  
Vol 852 ◽  
pp. 666-674 ◽  
Author(s):  
Emerald Ninolin ◽  
Godson Asirvatham Lazarus ◽  
K. Ramachandran
Keyword(s):  
Heat Transfer ◽  
Silver Nanoparticles ◽  
Heat Transfer Coefficient ◽  
Thermal Resistance ◽  
Transfer Coefficient ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Convective Heat Transfer Coefficient ◽  
Loop Heat Pipe ◽  
Volume Percentage

The thermal performance of a compact loop heat pipe is fabricated and tested for different heat inputs ranging from 30 W to 500 W using water and silver-water nanofluid with low volume concentrations of silver nanoparticles (0.03% and 0.09%) in vertical orientation. A flat square evaporator having a bottom area of 30 mm × 30 mm and a height of 15 mm is used in the present study. The effect of heat input on the thermal resistance, evaporation and condensation heat transfer coefficient is experimentally investigated. The results showed that a reduction in the evaporator thermal resistance of 26.45% is achieved with 0.09 volume percentage of silver nanoparticles when compared with that of water. Further an enhancement in the convective heat transfer coefficient of 25.23% has been observed with the same volume concentration of silver nanoparticles. Addition of small amount of nanoparticles enhanced the operating range of heat pipe beyond 500 W and without the occurrence of any dry out conditions. From the outcome of this study, it is concluded that the compact loop heat pipe with flat square evaporator can be used for thermal control of electronic equipments with limited space.

Experimental and theoretical investigation of heat transfer characteristics of cylindrical heat pipe using Al2O3–SiO2/W-EG hybrid nanofluids by RSM modeling approach

2021 ◽  
Vol 68 (1) ◽  
Author(s):  
R. Vidhya ◽  
T. Balakrishnan ◽  
B. Suresh Kumar
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Heat Transfer Coefficient ◽  
Thermal Resistance ◽  
Transfer Coefficient ◽  
Heat Pipe ◽  
Diffraction Spectrum ◽  
Step Method ◽  
Ceramic Nanoparticles ◽  
Transfer Mechanisms

AbstractNanofluids are emerging two-phase thermal fluids that play a vital part in heat exchangers owing to its heat transfer features. Ceramic nanoparticles aluminium oxide (Al2O3) and silicon dioxide (SiO2) were produced by the sol-gel technique. Characterizations have been done through powder X-ray diffraction spectrum and scanning electron microscopy analysis. Subsequently, few volume concentrations (0.0125–0.1%) of hybrid Al2O3–SiO2 nanofluids were formulated via dispersing both ceramic nanoparticles considered at 50:50 ratio into base fluid combination of 60% distilled water (W) with 40% ethylene glycol (EG) using an ultrasonic-assisted two-step method. Thermal resistance besides heat transfer coefficient have been examined with cylindrical mesh heat pipe reveals that the rise of power input decreases the thermal resistance and inversely increases heat transfer coefficient about 5.54% and 43.16% respectively. Response surface methodology (RSM) has been employed for the investigation of heat pipe experimental data. The significant factors on the various convective heat transfer mechanisms have been identified using the analysis of variance (ANOVA) tool. Finally, the empirical models were developed to forecast the heat transfer mechanisms by regression analysis and validated with experimental data which exposed the models have the best agreement with experimental results.

scholarly journals Enhancement of Nucleate Pool Boiling Heat Transfer with Sodium Oleate

2017 ◽  
Vol 29 (1) ◽  
pp. 44-48
Author(s):  
KM Tanvir Ahmmed ◽  
Sultana Razia Syeda
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Sodium Oleate ◽  
Surfactant Concentration ◽  
Chemical Engineering ◽  
Pool Boiling ◽  
Nucleate Pool Boiling ◽  
Maximum Heat ◽  
Maximum Heat Transfer

In this study saturated nucleate pool boiling of water with sodium oleate surfactant on a horizontal cylindrical heater surface has been investigated experimentally and compared with that of demineralized water. The concentration of sodium oleate in water was 100-300 ppm. The experimental results show that a small amount of surfactant enhances the heat transfer coefficient significantly. At low surfactant concentrations, heat transfer coefficient increases with increasing surfactant concentration in water. The maximum heat transfer enhancement is found to be at 250 ppm of sodium oleate solution. By adding more surfactant to water, heat transfer coefficient is found to be lowered. Surface tension of different concentration of sodium oleate solutions is measured. It is observed that the maximum heat transfer coefficient is obtained at a surfactant concentration that corresponds to the critical micelle concentration (cmc) of the sodium oleate solution.Journal of Chemical Engineering, Vol. 29, No. 1, 2017: 44-48

scholarly journals Comparison of heat transfer performance of ZnO-PG, α-Al2O3-PG, and γ-Al2O3-PG nanofluids in car radiator

2019 ◽  
Vol 9 ◽  
pp. 184798041987646 ◽  
Author(s):  
XiaoRong Zhou ◽  
Yi Wang ◽  
Kai Zheng ◽  
Haozhong Huang
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Propylene Glycol ◽  
Flow Rate ◽  
Volume Concentration ◽  
Maximum Heat ◽  
Cooling Performance ◽  
Maximum Heat Transfer ◽  
The Heat Transfer Coefficient

In this study, the cooling performance of nanofluids in car radiators was investigated. A car radiator, temperature measuring instrument, and other components were used to set up the experimental device, and the temperature of nanofluids passing through the radiator was measured by this device. Three kinds of nanoparticles, γ-Al2O3, α-Al2O3, and ZnO, were added to propylene glycol to prepared nanofluids, and the effects of nanoparticle size and type, volume concentration, initial temperature, and flow rate were tested. The results indicated that the heat transfer coefficients of all nanofluids first increased and then decreased with an increase in volume concentration. The ZnO-propylene glycol nanofluid reached a maximum heat transfer coefficient at 0.3 vol%, and the coefficient decreased by 25.6% with an increase in volume concentration from 0.3 vol% to 0.5 vol%. Smaller particles provided a better cooling performance, and the 0.1 vol% γ-Al2O3-propylene glycol nanofluid had a 19.9% increase in heat transfer coefficient compared with that of α-Al2O3-propylene glycol. An increase in flow rate resulted in a 10.5% increase in the heat transfer coefficient of the 0.5 vol% α-Al2O3-propylene glycol nanofluid. In addition, the experimental temperature range of 40–60°C improved the heat transfer coefficient of the 0.2 vol% ZnO-propylene glycol nanofluid by 46.4%.

Thermal Characteristics of a Cylindrical Heat Pipe using Multi-Layer Screen Mesh Wick

2018 ◽  
Vol 10 (5) ◽  
Author(s):  
R. Sankar Rao ◽  
S. Bhanu Prakash
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Thermal Resistance ◽  
Transfer Coefficient ◽  
Heat Pipe ◽  
Thermal Characteristics ◽  
Wire Mesh ◽  
Working Fluid ◽  
Wick Structure ◽  
Screen Mesh

Heat pipe is the most widely used heat exchanging device in removal of heat from any given system at a faster rate. The thermal characteristics of heat pipe with single and multi-layered screen mesh wicks have been observed with two working fluids water and acetone. Heat pipe of length 250 mm and 12.7 mm outer diameter, made of copper material is used in all the trials of with and without wick structure. A 100 mesh stainless steel screen wire mesh is chosen as wick structure. Experiments were conducted at different heat loads and various inclinations with 100% fill ratio in evaporator. The performance is measured based on total thermal resistance and overall heat transfer coefficient. The heat pipe is found effective at 60o inclination with acetone as a working fluid and with four layered screen mesh wick. Uncertainty in thermal resistance and heat transfer coefficient is calculated for a heat input of 10W at 0 and 60 inclinations.

Heat transfer characterization under radial jet and falling film induced rewetting

Kerntechnik ◽  
2021 ◽  
Vol 86 (5) ◽  
pp. 325-337
Author(s):  
M. Kumar ◽  
D. Mukhopadhyay
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Mass Flow Rate ◽  
Flow Rate ◽  
Jet Impingement ◽  
Falling Film ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Fuel Pin

Abstract Empirical correlations are developed for rewetting velocity and maximum heat transfer coefficient during rewetting phase of single hot vertical Fuel Pin Simulator (FPS) by using radial jet impingement and falling film. Emergency Core Cooling System (ECCS) has been designed for Advance Heavy water Reactor (AHWR) to rewet the hot fuel pin under the loss of coolant accident. Coolant injection takes place from a water rod which is located at the center of the fuel bundle in form of jets to rewet hot surface of fuel pin under loss of coolant accident. This kind of design to reflood the fuel bundle is different than bottom and top spray reflooding practiced in PWR and BWR type of nuclear reactors. There are two different kinds of rewetting found during radial jet induced cooling. The first one is due to radial jet impingement and the second one is due to falling film which is below the jet impingement point. Rewetting velocity has been predicted along the length of fuel pin due to radial jet impingement cooling. Temperature of FPS has been varied from 400°C to 700°C with help of different powers supply, simulating decay heat of reactor. A variation of coolant radial jet mass flow rate is from 0.5 lpm to 1.8 lpm. It is considered during ECCS injection. It has been observed from the experiments that rewetting velocity decreases with increasing the clad surface temperature and increases with increasing the coolant mass flow rate. The rewetting velocity in falling film is found to be nearly 1.8 times higher than rewetting velocity predicted in circumferential direction. Further, it is found that maximum heat transfer coefficient increases with increasing the radial jet coolant mass flow rate. The maximum heat transfer coefficient in case of radial jet impingement is found to be nearly 1.5 times the falling film rewetting. Developed correlation predicts the maximum heat transfer coefficient with experimental data well within the error band of ±10%.

Sign in / Sign up

Export Citation Format

Share Document