scholarly journals Rebonding of Orthodontic Brackets

2008 ◽  
Vol 78 (3) ◽  
pp. 531-536 ◽  
Author(s):  
Mona A. Montasser ◽  
James L. Drummond ◽  
Carla A. Evans
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Clinical Performance ◽  
Adhesive System ◽  
Orthodontic Brackets ◽  
Adhesive Systems ◽  
Adhesive Remnant Index ◽  
Acid Etch ◽  
The Mean ◽  
Self Etch

Abstract Objective: To compare rebonding of orthodontic brackets based on the hypothesis that no difference would be found between the adhesive systems with respect to shear bond strength, mode of failure, and clinical failure rates. Materials and Methods: The three adhesive systems included two self-etch primers (Transbond and M-Bond) and a conventional phosphoric acid etch (Rely-a-Bond). The sample size was 20 premolars for each adhesive system. The shear bond strength was tested 24 hours after bracket bonding with the bonding/debonding procedures repeated two times after the first debonding. Bond strength, adhesive remnant index (ARI), and failure sites were evaluated for each debonding. Statistical analysis consisted of a two-way analysis of variance (ANOVA) followed by Scheffè analysis. The clinical portion evaluated 15 patients over a 12-month period. Results: The mean shear bond strengths after the first, second, and third debondings for Rely-a-Bond were 8.4 ± 1.8, 10.3 ± 2.4, and 14.1 ± 3.3 MPa, respectively; for Transbond 11.1 ± 4.6, 13.6 ± 4.5, and 12.9 ± 4.4 MPa, respectively; and for M-Bond 8.7 ± 2.7, 10.4 ± 2.4, and 12.4 ± 3.4 MPa, respectively. After the three debondings the mean shear bond strength increased significantly from the first to the third debonding for Rely-a-Bond and M-bond (P ≤ .001), but did not change for Transbond (P = .199). Conclusions: The original hypothesis is not rejected. The two self-etching primers showing higher or comparable bond strength to the conventional phosphoric etch with less adhesive remnant on the enamel surface after the first debonding. With repeated bonding/debonding, the differences in the bond strength, ARI, and failure site were not significantly different. There was no difference in the clinical performance of the three adhesive systems (P = .667).

scholarly journals Effect of Self-etch Primer-adhesive and Conventional Adhesive Systems on the Shear Bond Strength and Bond Failure of Orthodontic Brackets: A Comparative Study

2015 ◽  
Vol 16 (2) ◽  
pp. 130-134 ◽  
Author(s):  
N Sanjay ◽  
RNG Rajesh ◽  
KS Girish ◽  
Malthesh B Savakkanavar ◽  
S Sreedhara ◽  
...  
Keyword(s):  
Bond Strength ◽  
Comparative Study ◽  
Shear Bond Strength ◽  
Adhesive System ◽  
Orthodontic Brackets ◽  
Adhesive Systems ◽  
Bond Failure ◽  
Fifth Generation ◽  
Sixth Generation ◽  
Self Etch

ABSTRACT Background Prompt-L-Pop is a sixth generation bonding system contains methacrylated phosphoric acid esters that combine an acidic component for etching the enamel and a primer, is an all-in-one adhesive. This study was undertaken to compare the bonding strength of brackets to enamel with traditional bonding technique and the new Prompt-L-Pop system using the same composite resin. Materials and methods In this in vitro experimental study, 60 human premolar teeth extracted for orthodontic treatment were collected. The samples were randomly divided into three groups comprising of 20 teeth in each group. Shear bond strength and ARI scores for the specimens were measured. Comparison was done using one way ANOVA and Chi-square test. Results Fourth generation bonding adhesive system depicted similar bond strength to fifth generation bonding adhesive system. Both fourth and fifth generation exhibited higher shear bond strength as compared to sixth generation bonding adhesive system. Conclusion Fourth and fifth generation exhibited higher shear bond strength as compared to sixth generation bonding adhesive system but the sixth generation has clinically acceptable shear bond strength. Also, it was found that sixth generation leaves less residual adhesive on the tooth after bracket removal. How to cite this article Sreedhara S, Savakkanavar MB, Rajesh RNG, Ankireddy RKR, Sanjay N, Girish KS. Effect of Self-etch Primer-adhesive and Conventional Adhesive Systems on the Shear Bond Strength and Bond Failure of Orthodontic Brackets: A Comparative Study. J Contemp Dent Pract 2015;16(2):130-134.

scholarly journals Shear Strength of Brackets Bonded with Universal Adhesive Containing 10-MDP after 20,000 Thermal Cycles

2020 ◽  
Vol 2020 ◽  
pp. 1-7
Author(s):  
Mariana Almeida Mello Proença ◽  
Karime Tavares Lima da Silva ◽  
Alisson Costa e Silva ◽  
Edilausson Moreno Carvalho ◽  
José Bauer ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Dental Enamel ◽  
Adhesive System ◽  
Test Machine ◽  
Adhesive Systems ◽  
Thermal Cycles ◽  
Universal Adhesive ◽  
Adhesive Remnant Index ◽  
One Way Anova

Objectives. The aim of this study was to evaluate the shear bond strength of metal brackets bonded with different universal adhesive systems containing 10-MDP and Transbond Plus Self Etching Primer after 20,000 thermal cycles. Materials and Methods. A total of 130 sound bovine teeth were used, which are divided into 5 groups (n = 26) according to the adhesive system used: All-Bond Universal (Bisco), Ambar Universal (FGM), Clearfil Universal Bond (Kuraray), Single Bond Universal (3M/ESPE), and Transbond Plus SEP (3M/ESPE) as control. The adhesives were applied for 20 seconds and bonded with a resin Transbond XT (3M/ESPE). After this, the teeth were submitted to 20,000 cycles at 5°C and 55°C. Afterwards, the shear bond strength test was performed in a universal test machine (Instron 3342). The adhesive remnant index (ARI) was evaluated under a stereomicroscope at 10x magnification and scanning electronic microscopy (SEM, Hitachi 3030). The shear bond strength data were submitted to One-Way ANOVA (α = 0.05) and the ARI to the Kruskal–Wallis test (α = 0.05). Results. Statistical analysis showed that the universal adhesive systems presented mean shear bond strength values similar to Transbond Plus SEP (p<0.05). The universal adhesive presented similar ARI values among them but differed from those of Transbond Plus SEP (p<0.001). Transbond Plus SEP presented a high ARI value when compared with the universal adhesive systems and high demineralization of enamel. Conclusions. The results show that universal adhesive systems may be used for bonding metal brackets if the orthodontist wants to maintain dental enamel health.

scholarly journals Shear Bond Strength of Brackets Rebonded with a Fluoride-Releasing and -Recharging Adhesive System

2009 ◽  
Vol 79 (3) ◽  
pp. 564-570 ◽  
Author(s):  
Toshiya Endo ◽  
Rieko Ozoe ◽  
Koichi Shinkai ◽  
Makiko Aoyagi ◽  
Hiroomi Kurokawa ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Failure Modes ◽  
Testing Machine ◽  
Adhesive System ◽  
Adhesive Systems ◽  
Bond Failure ◽  
Minimum Requirement ◽  
Adhesive Remnant Index ◽  
Bond Strengths

Abstract Objective: To ascertain the effects of repeated bonding on the shear bond strength of orthodontic brackets bonded with a fluoride-releasing and -recharging adhesive system with a self-etching primer in comparison with two other types of adhesive system. Materials and Methods: A total of 48 premolars were collected and divided equally into three groups of 16. Each group was assigned one of three adhesive systems: Transbond XT, Transbond Plus, or a fluoride-releasing and -recharging adhesive system, Beauty Ortho Bond. Shear bond strength was measured 24 hours after bracket bonding, with the bonding/debonding procedures repeated twice after the first debonding. A universal testing machine was used to determine shear bond strengths, and bracket/adhesive failure modes were evaluated with the adhesive remnant index after each debonding. Results: At every debonding sequence, all of these three adhesive systems had a shear bond strength of 6 MPa, which is a minimum requirement for clinical use. Transbond XT and Transbond Plus had significantly higher mean shear bond strengths than did Beauty Ortho Bond at each debonding. No significant differences in mean bond strength were observed between the three debondings in each adhesive system. Bond failure at the enamel/adhesive interface occurred more frequently in Beauty Ortho Bond than in Transbond XT or Transbond Plus. Conclusions: The fluoride-releasing and -recharging adhesive system with the self-etching primer (Beauty Ortho Bond) had clinically sufficient shear bond strength in repeated bracket bonding; this finding can help orthodontists to decrease the risk of damage to enamel at debonding.

scholarly journals Aplikasi klorheksidin glukonat 2%pada dentin tidak mempengaruhi kuat rekat geserkomposit resinyangmenggunakansistem adesif self etch (2% Chlorhexidine gluconate application on dentine does not affect bond strength of resin composite using self etch adhesive system)

2014 ◽  
Vol 13 (1) ◽  
pp. 7
Author(s):  
Dewi Puspitasari ◽  
Andi Soufyan ◽  
Ellyza Herda
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Composite Resin ◽  
Resin Composite ◽  
Testing Machine ◽  
Adhesive System ◽  
Chlorhexidine Gluconate ◽  
Adhesive Systems ◽  
Group I ◽  
Self Etch

Composite resin is a widely used aesthetic restoration. The restoration can fail due to secondary caries. Chlorhexidinegluconate 2% is used as a cavity disinfectant to eliminate microorganisms on the prepared cavity and to prevent thesecondary caries. The purpose of this study was to analyze the effect of chlorhexidine gluconate 2% to the bondstrength of composite resin with self etch system adhesive on dentine. Sixteen specimens of buccal dentine of premolarscrown are divided into 2 different groups. Group I: Clearfil SE Bond self-etch primer was applied for 20 seconds,Clearfil SE Bond bonding was applied for 5 seconds and polymerized for 10 seconds. Composite resin was constructedincrementally and polymerized for 20 seconds. Group II: prior to self etch primer application as in group I,chlorhexidine gluconate 2% was applied for 15 seconds. Shear bond strength was tested using Testing machine andanalyzed with unpaired T test. The highest shear bond strength was obtained by applying chlorhexidine gluconate 2%.The study concludes that chlorhexidine gluconate 2% application to dentine did not affect significantly to the bondstrength composite resin using self etch adhesive systems.

scholarly journals The Impact of Expasyl® Gingival Retraction Paste on the Bond Strength of Self-etch and Total-etch Systems

2015 ◽  
Vol 16 (5) ◽  
pp. 335-339 ◽  
Author(s):  
Zeeshan H Ahmad ◽  
Sukumaran Anil ◽  
Alaa El Araby ◽  
Mohammad D Al Amri
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Adhesive System ◽  
The Self ◽  
Adhesive Systems ◽  
Lower Performance ◽  
The Impact ◽  
Self Etch

ABSTRACT Objective To evaluate the influence of Expasyl® gingival retraction paste on the shear bond strength of self-etch and total-etch adhesive systems. Materials and methods Twenty-four specimens of extracted, caries-free, sound human molars were used in this study. The molars were then cut vertically into halves through the buccal and lingual cusps. Forty-eight specimens were divided into four groups (total-etch, total-etch with Expasyl application, self-etch, self-etch with Expasyl application) and the shear bond strength was tested. Results Expasyl significantly reduced the shear bond strength of the self-etch and total-etch adhesive systems. The self-etch system showed relatively lower performance compared with the total-etch adhesive system. The shear bond strength values of the total-etch adhesive without Expasyl showed the highest bond strength (21.48 ± 2.89), while the self-etching group adhesive treated with Expasyl showed the lowest shear bond strength value (14.89 ± 1.81). Conclusion From the observations of this in vitro study, it can be concluded that the use of Expasyl® gingival retraction system can negatively affect bond strength of adhesives. The total-etch system showed better compatibility to the Expasyl gingival retraction system than the self-etch. How to cite this article Al Baker AMA, El Araby A, Al Amri MD, Sukumaran A. The Impact of Expasyl® Gingival Retraction Paste on the Bond Strength of Self-etch and Total-etch Systems. J Contemp Dent Pract 2015;16(5):335-339.

scholarly journals Comparison of Shear Bond Strength and Adhesive Remnant Index of Brackets Bonded with Two Types of Orthodontic Adhesives

2017 ◽  
Vol 54 (1) ◽  
pp. 141-144 ◽  
Author(s):  
Elsaafin Mahmoud ◽  
Mariana Pacurar ◽  
Edwin Sever Bechir ◽  
Marius Maris ◽  
Cristian Olteanu ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Adhesive System ◽  
The Other ◽  
Adhesive Systems ◽  
The Third ◽  
Orthodontic Adhesives ◽  
Adhesive Remnant Index

The aim of this study was to evaluate shear bond strength and adhesive remnant index between two different brands of adhesive systems and brackets. The adhesive systems were represented by Opal Bond MV Composite and Opal Seal (Ultradent), respectively the fluoride releasing Transbond light cure adhesive paste and Transbond XT (3M). The utilised brackets were Avex metal bracket system (Ultradent), respectively Unitek™ Miniature Twin Metal Brackets (3M). The study was realized on 4 groups of extracted teeth: the first and second groups by using the products of the manufacturer Ultradent, respectively 3M, and the third and fourth groups by using the adhesive system of one manufacturer and the brackets of the other manufacturer. The study revealed that the use of adhesive system and brackets of the same manufacturer may increase the shear bond strength and decrease the adhesive remnant index.

scholarly journals Comparison of shear bond strength of orthodontic brackets bonded with a universal adhesive using different etching methods

2019 ◽  
Vol 24 (4) ◽  
pp. 33.e1-33.e8 ◽  
Author(s):  
Fereshteh Shafiei ◽  
Ahmadreza Sardarian ◽  
Reza Fekrazad ◽  
Amin Farjood
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Laser Etching ◽  
Universal Adhesive ◽  
Laser Conditioning ◽  
Adhesive Remnant Index ◽  
Acid Etch ◽  
Maxillary Premolars ◽  
Bond Strengths ◽  
Self Etch

ABSTRACT Objective: The aim of this study was to compare the effects of three enamel etching modes - laser-etch, self-etch and acid-etch (5, 10 and 15 s) - on bracket bonding, using a universal adhesive. Methods: Eighty-four maxillary premolars were randomly divided into seven groups (n=12) based on the etching method and the adhesive used for bracket bonding. After water storage and thermocycling, shear bond strength was measured, and adhesive remnant index scores on debonded enamel were determined. Results: There were significant differences between the seven groups regarding bond strength values (p< 0.001). The highest values were observed in universal adhesive with laser etching group, while Transbond XT with acid or laser etching, and universal adhesive used in self-etch mode demonstrated the lowest bond strength. The universal adhesive with the three different etching times presented with statistically similar results, all showing an improvement in bond strength, compared with Scotchbond universal (SBU)/SE. Conclusions: The universal adhesive evaluated in the present study demonstrated statistically similar bond strengths to conventional orthodontic adhesive in self-etch mode. The bond strength can be improved by adding an initial acid etching or laser conditioning step, although enamel damage was observed in some cases.

scholarly journals Shear bond strength of metallic and ceramic brackets using color change adhesives

2013 ◽  
Vol 18 (2) ◽  
pp. 76-80 ◽  
Author(s):  
Aisha de Souza Gomes Stumpf ◽  
Carlos Bergmann ◽  
José Renato Prietsch ◽  
Juliane Vicenzi
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Color Change ◽  
Testing Machine ◽  
Adhesive System ◽  
Bonding Material ◽  
Universal Testing ◽  
Adhesive Remnant Index ◽  
Ceramic Brackets ◽  
The Mean

OBJECTIVE: To determine the shear bond strength of orthodontic brackets using color change adhesives that are supposed to aid in removing excess of bonding material and compare them to a traditional adhesive. METHODS: Ninety metallic and ninety ceramic brackets were bonded to bovine incisors using two color change adhesives and a regular one. A tensile stress was applied by a universal testing machine. The teeth were observed in a microscope after debonding in order to determine the Adhesive Remnant Index (ARI). RESULTS: The statistical analysis (ANOVA, Tukey, and Kruskall-Wallis tests) demonstrated that the mean bond strength presented no difference when metallic and ceramic brackets were compared but the bond resistance values were significantly different for the three adhesives used. The most common ARI outcome was the entire adhesive remaining on the enamel. CONCLUSIONS: The bond strength was similar for metallic and ceramic brackets when the same adhesive system was used. ARI scores demonstrated that bonding with these adhesives is safe even when ceramic brackets were used. On the other hand, bond strength was too low for orthodontic purposes when Ortho Lite Cure was used.

scholarly journals Effect of EDTA and Phosphoric Acid Pretreatment on the Bonding Effectiveness of Self-Etch Adhesives to Ground Enamel

2010 ◽  
Vol 04 (04) ◽  
pp. 418-428 ◽  
Author(s):  
Ihab M. Ibrahim ◽  
Dina W. Elkassas ◽  
Mai M. Yousry
Keyword(s):  
Phosphoric Acid ◽  
Bond Strength ◽  
Surface Topography ◽  
Shear Bond Strength ◽  
Adhesive System ◽  
Adhesive Systems ◽  
Acid Pretreatment ◽  
Etching Pattern ◽  
Ground Enamel ◽  
The Mean

Objectives: This in vitro study determined the effect of enamel pretreatment with phosphoric acid and ethylenediaminetetraacetic acid (EDTA) on the bond strength of strong, intermediary strong, and mild self-etching adhesive systems.Methods: Ninety sound human premolars were used. Resin composite cylinders were bonded to flat ground enamel surfaces using three self-etching adhesive systems: strong Adper Prompt L-Pop (pH=0.9–1.0), intermediary strong AdheSE (pH=1.6–1.7), and mild Frog (pH=2). Adhesive systems were applied either according to manufacturer instructions (control) or after pretreatment with either phosphoric acid or EDTA (n=10). After 24 hours, shear bond strength was tested using a universal testing machine at a cross-head speed of 0.5 mm/minute. Ultra-morphological characterization of the surface topography and resin/enamel interfaces as well as representative fractured enamel specimens were examined using scanning electron microscopy (SEM).Results: Neither surface pretreatment statistically increased the mean shear bond strength values of either the strong or the intermediary strong self-etching adhesive systems. However, phosphoric acid pretreatment significantly increased the mean shear bond strength values of the mild self-etching adhesive system. SEM examination of enamel surface topography showed that phosphoric acid pretreatment deepened the same etching pattern of the strong and intermediary strong adhesive systems but converted the irregular etching pattern of the mild self-etching adhesive system to a regular etching pattern. SEM examination of the resin/enamel interface revealed that deepening of the etching pattern was consistent with increase in the length of resin tags. EDTA pretreatment had a negligible effect on ultra-morphological features.Conclusions: Use of phosphoric acid pretreatment can be beneficial with mild self-etching adhesive systems for bonding to enamel. (Eur J Dent 2010;4:418-428)

scholarly journals Effect Of Chitosan Treatment On Shear Bond Strength Of Composite To Deep Dentin Using Self-Etch And Total-Etch Adhesive Systems

2021 ◽  
Vol 24 (2) ◽  
Author(s):  
Fateme Vasei ◽  
Farahnaz Sharafeddin
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Resin Composite ◽  
Testing Machine ◽  
Adhesive System ◽  
Single Bond ◽  
Adhesive Systems ◽  
Etch And Rinse ◽  
Significant Difference ◽  
Self Etch

Objective: To assess the shear bond strength (SBS) of resin composite to deep dentin, using 1 and 2.5% chitosan pretreatment as well as different adhesive systems. Material and Methods: 80 human maxillary molars were randomly divided to eight groups according to the type of adhesive system and dentin pretreatment (n = 10): I) two-step self-etch system (Clearfil SE bond); II) two-step etch-andrinse system (Adper single bond 2); III) 2.5% chitosan + Clearfil SE bond; IV) 2.5% chitosan +etch + Adper single bond 2; V) etch + 2.5% chitosan + Adper single bond 2; VI) 1% chitosan + Clearfil SE bond; VII) 1% chitosan + etch + Adper single bond 2; VIII) etch + 1% chitosan + Adper single bond 2 (chitosan solution (w/v): 2.5 g and 1 g of chitosan (Sigma Aldrich, USA) was dissolved in 100 ml of 1% acetic acid). Plastic molds were positioned on dentin and filled with composite (Z350, 3M ESPE, USA). SBS (MPa) was tested using a universal testing machine. ANOVA tests, Tukey’s test, and independent t test were used to analyze data (p < 0.05). Results: The highest SBS value among self-etch groups was observed with 1% chitosan (p = 0.001). In the etch-and-rinse group, the SBS of 1% chitosan was significantly lower than the other groups. Chitosan treatment following acid etching led to higher SBS in comparison to when chitosan was applied before etching, with the significant difference in 1% concentration (p = 0.030). A predominance of mix fractures was observed in dentin. Conclusion: Improved dentin bond strength can be achieved through immediate dentin pretreatment with 1% chitosan in self-etch adhesive systems. Chitosan Pretreatment may not be advantageous for etch-and-rinse adhesive systems. Keywords Adhesive system; Chitosan; Deep dentin; Shear strength.

Sign in / Sign up

Export Citation Format

Share Document