scholarly journals Titanium and Stainless Steel MIG LSC Welding

2019 ◽  
Vol 22 (2) ◽  
pp. 56-59
Author(s):  
Nela Poláková ◽  
Petr Dostál
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Arc Welding ◽  
Galvanic Corrosion ◽  
Welding Process ◽  
Protective Atmosphere ◽  
Metallographic Analysis ◽  
Chemical Compositions ◽  
Additional Material ◽  
Welding Method

Abstract This paper deals with the issue of welding two different materials – titanium and stainless steel (UNS N50400 + X5CrNi 18-10). These two materials have completely different chemical compositions and mechanical properties; therefore, process of their mutual welding is complicated. Melting temperature of both materials is also different. An innovative MIG LSC arc welding method with an additional material has been selected for this purpose. A protective atmosphere was used in order to avoid galvanic corrosion of materials that would preclude the welding process. Aforementioned atmosphere contained 100% Ar. The MIG LSC welding method was designed by Fronius. Presented experiment compares utilization of following 4 different electrodes (additional material) for the welding of titanium and stainless steel: Ti, Fe, corrosion-resistant Fe and CuSi3 electrode. Tensile test was utilized for evaluation of weldment mechanical properties. Measured results were supplemented with a metallographic analysis snapshot and tensile diagram.

Effect of TIG Welding and Manual Metal Arc Welding on Mechanical Properties of AISI 304 and 316L Austenitic Stainless Steel Sheets

2017 ◽  
Vol 750 ◽  
pp. 26-33
Author(s):  
Alaa Abu Harb ◽  
Ion Ciuca ◽  
Robert Ciocoiu ◽  
Mihai Vasile ◽  
Adrian Bibis ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Arc Welding ◽  
Welding Process ◽  
Central Hole ◽  
Steel Sheets ◽  
Metal Arc Welding ◽  
316L Austenitic Stainless Steel ◽  
Better Than

The welding technique used for ASIS 304 and 316L austenitic stainless steel sheets both with a thickness of 3mm is gas tungsten arc welding (TIG) and manual metal arc welding (MMAW). Mechanical properties that were verified include: hardness test and tensile test before welding and after it. The welding process was done on two types of specimens: with a central hole and without hole. We concluded that there was a decrease in the properties of tensile for both specimens with central hole, and 316L had tensile characteristics better than 304 when using the technique TIG. As for 304, it had tensile characteristics better than 316L when using the technique MMAW. We also concluded that the existence of central holes had an influence on the hardness characteristics on both types. The hardness increased in 304 but decreased in 316L. The welding process also showed that there was no influence of MMAW on hardness on both specimens. However it showed that there was no influence of TIG on the hardness for 304, but for 316L values increased.

scholarly journals CMT Welding of Titanium and Stainless Steel Using CuSi3 Electrode

2019 ◽  
Vol 67 (1) ◽  
pp. 147-153
Author(s):  
Nela Poláková ◽  
Petr Dostál
Keyword(s):  
Stainless Steel ◽  
Fusion Welding ◽  
Gas Absorption ◽  
Protective Atmosphere ◽  
Metallographic Analysis ◽  
Welding Parameters ◽  
Additional Material ◽  
Measurement Results ◽  
Cmt Welding

The article deals with the possibility of a tight permanent joint of X5CrNi 18–10 austenitic steel and UNS N50400 titanium. The nuclear and chemical industries are in particular interested in solving this problem. The joining by means of fusion welding has come up against unreliability due to the formation of brittle intermetallic compounds between titanium and iron. The article deals with joining of these two heterogeneous materials by an innovative CMT welding method. CuSi3 soldering electrode was chosen as the additional material. Protective atmosphere consisting of clean argon has been chosen due to the undesirable gas absorption by titanium at temperatures over 600 °C. The results will compare different welding parameters and their impact on the quality of the weld joint. The quality of the created welds will be verified on the basis of the tensile test and the results will be graphically visualized. The microhardness in the weld and its surroundings will be measured. The microhardness measurement results will be graphically displayed. The experimental results will be supplemented by macrostructure snapshots and metallographic analysis snapshots.

Microstructure and mechanical properties of ADC12/6063-T6 aluminum alloy butt joint achieved by metal inert gas groove welding

2018 ◽  
Vol 233 (10) ◽  
pp. 2120-2124
Author(s):  
Ye Wang ◽  
Mi Zhao ◽  
Hongyu Xu ◽  
Maoliang Hu ◽  
Zesheng Ji
Keyword(s):  
Mechanical Properties ◽  
Arc Welding ◽  
Welding Process ◽  
Weld Interface ◽  
Butt Joint ◽  
Inert Gas ◽  
Butt Joints ◽  
Arc Welding Process ◽  
The Impact ◽  
Silicon Particles

Metal inert gas arc welding process was implemented to join 6063T6 wrought alloy and ADC12 die-casting alloy using ER4047 filler metal. The microstructure of the weld seam and weld interface was investigated. The bonding strength of the butt joints was tested by Charpy U-notch impact test and tensile test. The results showed that a sound welding butt joint with finely silicon particles and excellent mechanical properties was formed, and the size of the silicon particles was nearly 2 μm. Compared with 6063T6 wrought alloy, the impact absorbing energies and the tensile strengths of the butt joint were higher and reached 1.173 kJ/cm2 and 205 MPa, respectively, and the fractures of all tensile specimens occur at the 6063T6 aluminum.

scholarly journals Investigation of Microstructure and Corrosion Resistance of Dissimilar Welded Joint between 304 Stainless Steel and Pure Copper

2019 ◽  
Vol 1 (3) ◽  
pp. 76-82
Author(s):  
Sorush Niknamian
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Arc Welding ◽  
Pure Copper ◽  
Welding Process ◽  
Steel Part ◽  
304 Stainless Steel ◽  
Dissimilar Metals ◽  
304L Stainless Steel ◽  
Shielded Metal Arc Welding

Nowadays, welding of dissimilar metals has become significant. In this process, a number of parameters including but not limited to type of electrode, amount of current, preheating temperature, and welding rate, that are essential to be taken into account. For welding of dissimilar metals, various methods are exploited including shielded metal arc welding (SMAW) and gas tungsten arc welding (GTAW). The stimulus for studying welding of 304L stainless steel to pure copper originates from difficulties in joining copper parts of           water-circulating molds to their steel part. In this study, the welding is performed on plates of steel and copper using SMAW, GTAW and combined SMAW+GTAW welding methods with    EL-CuMn2, ENiCrMo-6 and ER70S-4 electrodes. In order to investigate the microstructure and corrosion resistance behavior of welds, the samples were characterized using microstructural study and polarization test. It was observed that among all four welding methods, only combined SMAW+GTAW welding process resulted in successful joint between 304L stainless steel and copper. Both obtained joints possess suitable microstructure and corrosion resistance.

scholarly journals Experimental and Numerical Analysis on TIG Arc Welding of Stainless Steel Using RSM Approach

Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1659
Author(s):  
Sasan Sattarpanah Karganroudi ◽  
Mahmoud Moradi ◽  
Milad Aghaee Attar ◽  
Seyed Alireza Rasouli ◽  
Majid Ghoreishi ◽  
...  
Keyword(s):  
Heat Flux ◽  
Stainless Steel ◽  
Welding Speed ◽  
Arc Welding ◽  
Welding Process ◽  
Weld Bead ◽  
Bead Geometry ◽  
Depth Of Penetration ◽  
Weld Bead Geometry ◽  
Bead Width

This study involves the validating of thermal analysis during TIG Arc welding of 1.4418 steel using finite element analyses (FEA) with experimental approaches. 3D heat transfer simulation of 1.4418 stainless steel TIG arc welding is implemented using ABAQUS software (6.14, ABAQUS Inc., Johnston, RI, USA), based on non-uniform Goldak’s Gaussian heat flux distribution, using additional DFLUX subroutine written in the FORTRAN (Formula Translation). The influences of the arc current and welding speed on the heat flux density, weld bead geometry, and temperature distribution at the transverse direction are analyzed by response surface methodology (RSM). Validating numerical simulation with experimental dimensions of weld bead geometry consists of width and depth of penetration with an average of 10% deviation has been performed. Results reveal that the suggested numerical model would be appropriate for the TIG arc welding process. According to the results, as the welding speed increases, the residence time of arc shortens correspondingly, bead width and depth of penetration decrease subsequently, whilst simultaneously, the current has the reverse effect. Finally, multi-objective optimization of the process is applied by Derringer’s desirability technique to achieve the proper weld. The optimum condition is obtained with 2.7 mm/s scanning speed and 120 A current to achieve full penetration weld with minimum fusion zone (FZ) and heat-affected zone (HAZ) width.

The Effect of Sub-Zero Treatment on Mechanical Properties of GTAW Welded AA6082

2016 ◽  
Vol 852 ◽  
pp. 349-354 ◽  
Author(s):  
R. Devanathan ◽  
Sanjivi Arul ◽  
T. Venkatamuni ◽  
D. Yuvarajan ◽  
D. Christopher Selvam
Keyword(s):  
Mechanical Properties ◽  
Arc Welding ◽  
Artificial Aging ◽  
Cryogenic Treatment ◽  
Welding Process ◽  
Travel Speed ◽  
Treatment Result ◽  
Gas Tungsten Arc ◽  
Shallow Cryogenic Treatment ◽  
Hardness Values

The consequence of sub-zero treatment on the mechanical properties of welded AA6082-T6 by Gas Tungsten Arc Welding (GTAW) which in turn softens the heat concentrated welded region owing to dissolution of the strengthening precipitates. The sub-zero i.e. Shallow Cryogenic Treatment (SCT) is carried out on GTAW welded plate having a thickness of 6 mm at -77°C by varying the electrode travel speed and sub-zero treatment periods. Welded region of AA6082 were tested for hardness and microstructure by adapting three different conditions such as welded, post weld artificial aging with and without sub-zero treatment. Result revealed that the amount of softening in the welded region is indirectly proportional to electrode travel speed during welding process. It is also observed that the post weld SCT with artificial aging has increased the micro hardness values on the welded region as a consequence of the reactivation in the sequence of precipitation.

Sign in / Sign up

Export Citation Format

Share Document