scholarly journals Calculating the Dynamic Impedances of Foundations and their Effect on the Seismic Response of Structures: Analytical and Numerical Study

2021 ◽  
Vol 31 (2) ◽  
pp. 178-217
Author(s):  
Radhwane Boulkhiout ◽  
Salah Messast
Keyword(s):  
Degrees Of Freedom ◽  
Numerical Study ◽  
Displacement Vector ◽  
Soft Soil ◽  
The Finite Element Method ◽  
Rheological Models ◽  
Soil Densification ◽  
Structure Height ◽  
Impedance Functions ◽  
Numerical Program

Abstract This study evaluates the movement of a frame built on soft soil under seismic excitation taking into account soil-structure interaction. First, the study was evaluated using the finite element method, then, by using a substructure method which modelled the soil using springs and dampers in a linear and nonlinear study. Rheological models were determined using impedance functions, calculated using a numerical program CONAN. These dynamic impedances are shown in the displacement vector of a three-degrees-of-freedom frame, which was calculated on the basis of lateral forces distributed over the structure height using the equivalent static method. In this regard, two different calculation norms were chosen; RPA2003 and UBC97. Finally, a parametric study was carried out, based on the effects of soil densification and the foundation geometry on the response of the RC frame.

scholarly journals GEOMETRIC EVALUATION OF COMPLEX CAVITY INTRUDED IN HEAT GENERATED WALLS

2017 ◽  
Vol 16 (1) ◽  
pp. 31
Author(s):  
M. V. F. Guimaraes ◽  
L. R. Emmendorfer ◽  
J. F. Prolo Filho ◽  
E. D. dos Santos
Keyword(s):  
Degrees Of Freedom ◽  
Numerical Study ◽  
Heat Diffusion ◽  
The Finite Element Method ◽  
Heat Diffusion Equation ◽  
Constructal Design ◽  
High Magnitude ◽  
Optimal Shapes ◽  
Complex Cavity ◽  
Volumetric Heat Generation

In this work it is presented a numerical study about geometrical evaluation of heat transfer in solids with volumetric heat generation and complex intruded cavity for cooling the wall by means of Constructal Design. Several cavities with varied shapes have been evaluated in literature, such as I-, T- and H-shaped cavities. The purpose here is to evaluate a complex cavity that combines different elemental shapes. More precisely, the resultant cavity is a merge between a H-shaped cavity and a I-shaped one, forming a ramified geometry, which is more expected in the flow between a point and volume in systems with high magnitude. The main purpose is to minimize two times the maximal temperature in the solid domain (Tmax). Here two degrees of freedom are defined for the cavity: H1/L1 (ratio between the second branch thickness and its length) and H0/L0 (ratio between the third branch height and its thickness) and the area of cavity is the constraint. For each geometrical configuration the heat diffusion equation is solved with the Finite Element Method (FEM). Results showed that differences of until five times between the optimal shapes and the worst ones are achieved, showing the importance of application of Constructal Design in the problem. Moreover, the best performance is achieved when the vertical branches are fully intruded in the solid domain for intermediate lengths of horizontal branch.

scholarly journals A Finite Element Approach to the Analysis of Rotating Bladed-Disk Assemblies Coupled With Flexible Shaft

1994 ◽  
Author(s):  
Wen Zhang ◽  
Wenliang Wang ◽  
Hao Wang ◽  
Jiong Tang
Keyword(s):  
Finite Element ◽  
Degrees Of Freedom ◽  
Coupled System ◽  
Equation Of Motion ◽  
Coupled Systems ◽  
The Finite Element Method ◽  
Bladed Disk ◽  
Modal Synthesis ◽  
Element Approach ◽  
Final Equation

A method for dynamic analysis of flexible bladed-disk/shaft coupled systems is presented in this paper. Being independant substructures first, the rigid-disk/shaft and each of the bladed-disk assemblies are analyzed separately in a centrifugal force field by means of the finite element method. Then through a modal synthesis approach the equation of motion for the integral system is derived. In the vibration analysis of the rotating bladed-disk substructure, the geometrically nonlinear deformation is taken into account and the rotationally periodic symmetry is utilized to condense the degrees of freedom into one sector. The final equation of motion for the coupled system involves the degrees of freedom of the shaft and those of only one sector of each of the bladed-disks, thereby reducing the computer storage. Some computational and experimental results are given.

Study of some rheological models with a finite number of degrees of freedom

2000 ◽  
Vol 19 (2) ◽  
pp. 277-307 ◽  
Author(s):  
Jérôme Bastien ◽  
Michelle Schatzman ◽  
Claude-Henri Lamarque
Keyword(s):  
Finite Number ◽  
Degrees Of Freedom ◽  
Rheological Models

Development of Reformative Surgery Method Using Partial Freezing for the Liver

2006 ◽  
Vol 128 (6) ◽  
pp. 862-866
Author(s):  
M. Takahashi ◽  
S. Nomura ◽  
M. Jindai ◽  
S. Shibata ◽  
X. Zhu ◽  
...  
Keyword(s):  
Cooling Rate ◽  
Degrees Of Freedom ◽  
Operation Time ◽  
Basic Research ◽  
Freezing Temperature ◽  
The Finite Element Method ◽  
Porcine Liver ◽  
Liver Sample ◽  
Peltier Module ◽  
Increment Rate

To minimize surgical stresses including blood loss and operation time to the patients during hepatic resection, we studied the feasibility of a combination of a partial liver freezing technique and shape-memory alloy, which also enables a free-designed resection curve. In this surgical procedure, the region surrounding a tumor in the liver is frozen to excise and prevent hemorrhage. The liver was frozen by a Peltier module. The effects of cooling rate and freezing temperature on the excision force that arise between a scalpel and the liver are carried out experimentally as a basic research for partial freezing surgical procedures. A porcine liver was used as a liver sample. The physical properties were estimated by using the finite element method based on the heat transfer characteristics of the liver. Isolation of the liver was conducted using a scalpel attached to the end-effector of a 3 degrees of freedom robot. In the experiments, the minimum excision force was obtained at a temperature between 272K and 275K; therefore, it is preferable that the liver be excised within this temperature range. Lowering of the cooling rate decreases the excision force even if the temperature of the liver remains unchanged. The lower the temperature of the liver is, the larger the increment rate of excision force is with regard to the cooling rate.

scholarly journals Ground settlement prediction of embankment treated with prefabricated vertical drains in soft soil

2018 ◽  
Vol 195 ◽  
pp. 03014
Author(s):  
Siswoko Adi Saputro ◽  
Agus Setyo Muntohar ◽  
Hung Jiun Liao
Keyword(s):  
Numerical Study ◽  
Soft Soil ◽  
Soil Permeability ◽  
K Value ◽  
Prefabricated Vertical Drains ◽  
Vertical Drains ◽  
Prefabricated Vertical Drain ◽  
Actual Settlement ◽  
Final Settlement ◽  
Best Fit

Excessive settlement due to consolidation can cause damage to the structure’s rest on soft soil. The settlement takes place in relatively longer. The preloading and prefabricated vertical drain (PVD) is often applied to accelerate the primary settlement. The issue in this research is the estimation of the settlement. The Asaoka method and the finite element method using PLAXIS-2D are used to estimate the final settlement of a PVD treated embankment. For the former, a complete record of the settlement was required; for the latter, some ground parameters are needed for the PLAXIS-2D analysis, such as the permeability of the soil. Because the installation process of PVD tends to influence the permeability of the in-situ soil around the PVD, the soil permeability after the installation of PVD needs to be adjusted. The numerical results were compared with actual settlement data to find out the best-fit input parameters (i.e. soil permeability) of the actual data. It was found that the best-fit soil permeability (k) used in the numerical study was about one-half of the k value determined from the laboratory test. The Root Mean Square Deviation shows that the settlement predicted by the numerical analysis has approximately 30% of the actual settlement.

Numerical Study of the Flow Forming Process of AISI 630 Stainless Steel

2011 ◽  
Vol 264-265 ◽  
pp. 24-29 ◽  
Author(s):  
Seyed Mohammad Ebrahimi ◽  
Seyed Ali Asghar Akbari Mousavi ◽  
Mostafa Soltan Bayazidi ◽  
Mohammad Mastoori
Keyword(s):  
Feeding Rate ◽  
Surface Defects ◽  
Numerical Study ◽  
Internal Diameter ◽  
The Finite Element Method ◽  
Forming Process ◽  
Flow Forming ◽  
Cold Forming ◽  
External Variables ◽  
Experimental Process

Flow forming is one of the cold forming process which is used for hollow symmetrical shapes. In this paper, the forward flow forming process is simulated using the finite element method and its results are compared with the experimental process. The variation of thickness of the sample is examined by the ultrasonic tests for the five locations of the tubes. To simulate the process, the ABAQUS explicit is used. The effects of flow forming variables such as the angle of rollers and rate of feeding of rollers, on the external variables such as internal diameter, thickness of tube and roller forces are considered. The study showed that the roller force and surface defects were reduced with low feeding rate and low rollers attack angles. Moreover, the sample internal diameter increased at low feeding rate and low rollers attack angles. The optimum variables for flow forming process were also obtained.

Numerical study on the mechanism of drag reduction for interceptors on planning boats

2021 ◽  
Author(s):  
Lianzheng Cui ◽  
Zuogang Chen ◽  
Yukun Feng
Keyword(s):  
Drag Reduction ◽  
High Speed ◽  
Degrees Of Freedom ◽  
Numerical Study ◽  
Dynamic Pressure ◽  
Motion Model ◽  
Gauge Pressure ◽  
Reduction Effect ◽  
Pressure Resistance ◽  
Viscous Pressure

The drag reduction effect of interceptors on planning boats has been widely proven, but the mechanism of the effect has been rarely studied in terms of drag components, especially for spray resistance. The resistance was caused by the high gauge pressure under the boats transformed from the dynamic pressure, and it is the largest drag component in the high-speed planning mode. In this study, numerical simulations of viscous flow fields around a planning boat with and without interceptors were conducted. A two degrees of freedom motion model was employed to simulate the trim and sinkage. The numerical results were validated against the experimental data. The flow details with and without the interceptor were visualized and compared to reveal the underlying physics. A thinner and longer waterline could be achieved by the interceptor, which made the boat push the water away more gradually, and hence, the wave-making resistance could be decreased. The improved waterline also reduced the component of the freestream normal to the hull surface and led to the less transformed dynamic pressure, resulting in the lowAer spray resistance. Furthermore, the suppression of the flow separation could also be benefited from the interceptor; the viscous pressure resistance was therefore decreased.

Evaluation of 3-D Computational Model of Oscillating Water Column Converter with Constructal Design with Three Degrees of Freedom and Limited Chimney Height

2021 ◽  
Vol 407 ◽  
pp. 128-137
Author(s):  
Vinícius Bloss ◽  
Camila Fernandes Cardozo ◽  
Flávia Schwarz Franceschini Zinani ◽  
Luiz Alberto Oliveira Rocha
Keyword(s):  
Water Column ◽  
Wave Energy ◽  
Degrees Of Freedom ◽  
Numerical Study ◽  
Mechanical Energy ◽  
Ocean Waves ◽  
Response Surfaces ◽  
Oscillating Water Column ◽  
Promising Source ◽  
Three Degrees Of Freedom

Theoretically, ocean waves contain enough mechanical energy to supply the entire world’s demand and, as of late, are seen as a promising source of renewable energy. To this end, several different technologies of Wave Energy Converters (WEC) have been developed such as Oscillating Water Column (OWC) devices. OWCs are characterized by a chamber in which water oscillates inside and out in a movement similar to that of a piston. This movement directs air to a chimney where a turbine is attached to convert mechanical energy. The analysis conducted was based on the Constructive Design Method, in which a numerical study was carried out to obtain the geometric configuration that maximized the conversion of wave energy into mechanical energy. Three degrees of freedom were used: the ratio of height to length of the hydropneumatic chamber (H1/L), the ratio of the height of the chimney to its diameter (H2/d) and the ratio of the width of the hydropneumatic chamber to the width of the wave tank (W/Z). A Design of Experiments (DoE) technique coupled with Central Composite Design (CCD) allowed the simulation of different combinations of degrees of freedom. This allowed the construction of Response Surfaces and correlations for the efficiency of the system depending on the degrees of freedom (width and height of the chamber), as well as the optimization of the system based on the Response Surfaces.

scholarly journals Modeling of Size Effects in Bending of Perforated Cosserat Plates

2017 ◽  
Vol 2017 ◽  
pp. 1-19 ◽  
Author(s):  
Roman Kvasov ◽  
Lev Steinberg
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Numerical Study ◽  
The Finite Element Method ◽  
Classical Elasticity ◽  
Element Analysis ◽  
Plate Deformation ◽  
The Finite Element Analysis ◽  
Circular Holes ◽  
Different Shapes

This paper presents the numerical study of Cosserat elastic plate deformation based on the parametric theory of Cosserat plates, recently developed by the authors. The numerical results are obtained using the Finite Element Method used to solve the parametric system of 9 kinematic equations. We discuss the existence and uniqueness of the weak solution and the convergence of the proposed FEM. The Finite Element analysis of clamped Cosserat plates of different shapes under different loads is provided. We present the numerical validation of the proposed FEM by estimating the order of convergence, when comparing the main kinematic variables with an analytical solution. We also consider the numerical analysis of plates with circular holes. We show that the stress concentration factor around the hole is less than the classical value, and smaller holes exhibit less stress concentration as would be expected on the basis of the classical elasticity.

Sign in / Sign up

Export Citation Format

Share Document