scholarly journals Comparison of Airborne Laser Scanning of Low and High Above Ground Level for Selected Infrastructure Objects

2018 ◽  
Vol 8 (2) ◽  
pp. 89-96 ◽  
Author(s):  
J. Siwiec
Keyword(s):  
Laser Scanning ◽  
New Technology ◽  
Ground Level ◽  
Point Clouds ◽  
Airborne Lidar ◽  
Structural Elements ◽  
Transmission Tower ◽  
Deviation Analysis ◽  
Airborne Laser ◽  
Internal Coherence

Abstract Along with the development of the technology of drone construction (UAV - Unmanned Aerial Vehicles), the number of applications of these solutions in the industry also grew. The aim of the research is to check the accuracy of data obtained using the new technology of UAV scanning and to compare them with one that is widely spread - high-altitude airborne Lidar, in terms of quality and spectrum of applications in industry and infrastructure. The research involved two infrastructure objects: a reinforced concrete one-span bridge and Lattice transmission tower with powerlines. The density of measurement, internal and external cohesion of point clouds obtained from both methods were compared. Plane fitting and deviation analysis were used. The data of UAV origin in both cases provided a sufficient density, allowing the recognition of structural elements, and internal coherence and precision of measurements important in modeling. The study shows that UAV mounted scanning may be used in the same applications as Airborne Lidar, as well as in other tasks requiring greater precision.

scholarly journals CLUSTERING OF MULTISPECTRAL AIRBORNE LASER SCANNING DATA USING GAUSSIAN DECOMPOSITION

2017 ◽  
Vol XLII-2/W7 ◽  
pp. 269-276 ◽  
Author(s):  
S. Morsy ◽  
A. Shaker ◽  
A. El-Rabbany
Keyword(s):  
Land Surface ◽  
Laser Scanning ◽  
Vegetation Indices ◽  
Gaussian Function ◽  
Expectation Maximization Algorithm ◽  
Point Clouds ◽  
Airborne Laser Scanning ◽  
Airborne Lidar ◽  
Airborne Laser ◽  
Gaussian Decomposition

With the evolution of the LiDAR technology, multispectral airborne laser scanning systems are currently available. The first operational multispectral airborne LiDAR sensor, the Optech Titan, acquires LiDAR point clouds at three different wavelengths (1.550, 1.064, 0.532 μm), allowing the acquisition of different spectral information of land surface. Consequently, the recent studies are devoted to use the radiometric information (i.e., intensity) of the LiDAR data along with the geometric information (e.g., height) for classification purposes. In this study, a data clustering method, based on Gaussian decomposition, is presented. First, a ground filtering mechanism is applied to separate non-ground from ground points. Then, three normalized difference vegetation indices (NDVIs) are computed for both non-ground and ground points, followed by histograms construction from each NDVI. The Gaussian function model is used to decompose the histograms into a number of Gaussian components. The maximum likelihood estimate of the Gaussian components is then optimized using Expectation – Maximization algorithm. The intersection points of the adjacent Gaussian components are subsequently used as threshold values, whereas different classes can be clustered. This method is used to classify the terrain of an urban area in Oshawa, Ontario, Canada, into four main classes, namely roofs, trees, asphalt and grass. It is shown that the proposed method has achieved an overall accuracy up to 95.1 % using different NDVIs.

scholarly journals AUTOMATIC EXTRACTION AND REGULARIZATION OF BUILDING OUTLINES FROM AIRBORNE LIDAR POINT CLOUDS

2016 ◽  
Vol XLI-B3 ◽  
pp. 555-560
Author(s):  
Bastian Albers ◽  
Martin Kada ◽  
Andreas Wichmann
Keyword(s):  
Laser Scanning ◽  
Viterbi Algorithm ◽  
Point Clouds ◽  
Airborne Laser Scanning ◽  
Airborne Lidar ◽  
Trade Off ◽  
Line Segments ◽  
Alpha Shape ◽  
3D Point Clouds ◽  
Airborne Laser

Building outlines are needed for various applications like urban planning, 3D city modelling and updating cadaster. Their automatic reconstruction, e.g. from airborne laser scanning data, as regularized shapes is therefore of high relevance. Today’s airborne laser scanning technology can produce dense 3D point clouds with high accuracy, which makes it an eligible data source to reconstruct 2D building outlines or even 3D building models. In this paper, we propose an automatic building outline extraction and regularization method that implements a trade-off between enforcing strict shape restriction and allowing flexible angles using an energy minimization approach. The proposed procedure can be summarized for each building as follows: (1) an initial building outline is created from a given set of building points with the alpha shape algorithm; (2) a Hough transform is used to determine the main directions of the building and to extract line segments which are oriented accordingly; (3) the alpha shape boundary points are then repositioned to both follow these segments, but also to respect their original location, favoring long line segments and certain angles. The energy function that guides this trade-off is evaluated with the Viterbi algorithm.

scholarly journals AUTOMATIC EXTRACTION AND REGULARIZATION OF BUILDING OUTLINES FROM AIRBORNE LIDAR POINT CLOUDS

2016 ◽  
Vol XLI-B3 ◽  
pp. 555-560 ◽  
Author(s):  
Bastian Albers ◽  
Martin Kada ◽  
Andreas Wichmann
Keyword(s):  
Laser Scanning ◽  
Viterbi Algorithm ◽  
Point Clouds ◽  
Airborne Laser Scanning ◽  
Airborne Lidar ◽  
Trade Off ◽  
Line Segments ◽  
Alpha Shape ◽  
3D Point Clouds ◽  
Airborne Laser

Building outlines are needed for various applications like urban planning, 3D city modelling and updating cadaster. Their automatic reconstruction, e.g. from airborne laser scanning data, as regularized shapes is therefore of high relevance. Today’s airborne laser scanning technology can produce dense 3D point clouds with high accuracy, which makes it an eligible data source to reconstruct 2D building outlines or even 3D building models. In this paper, we propose an automatic building outline extraction and regularization method that implements a trade-off between enforcing strict shape restriction and allowing flexible angles using an energy minimization approach. The proposed procedure can be summarized for each building as follows: (1) an initial building outline is created from a given set of building points with the alpha shape algorithm; (2) a Hough transform is used to determine the main directions of the building and to extract line segments which are oriented accordingly; (3) the alpha shape boundary points are then repositioned to both follow these segments, but also to respect their original location, favoring long line segments and certain angles. The energy function that guides this trade-off is evaluated with the Viterbi algorithm.

scholarly journals AIRBORNE TO UAS LIDAR: AN ANALYSIS OF UAS LIDAR GROUND CONTROL TARGETS

2019 ◽  
Vol XLII-2/W13 ◽  
pp. 255-262 ◽  
Author(s):  
L. Davidson ◽  
J. P. Mills ◽  
I. Haynes ◽  
C. Augarde ◽  
P. Bryan ◽  
...  
Keyword(s):  
Laser Scanning ◽  
Ground Level ◽  
Airborne Laser Scanning ◽  
Airborne Lidar ◽  
Mission Planning ◽  
Ground Control ◽  
Academic Literature ◽  
Airborne Laser ◽  
Control Target ◽  
Geomorphological Changes

<p><strong>Abstract.</strong> Creating accurate models of the Earth’s surface is an essential step when analysing geomorphological changes through time. Alongside photogrammetry, airborne lidar is an established method for measuring and modelling the Earth’s surface. However, improvements in size, weight and power requirements mean that lidar is now increasingly capable of being operated from Unpiloted Aircraft Systems (UASs). While academic literature is currently weighted towards issues associated with airborne laser scanning, UASs operate under different parameters to piloted aeroplanes and helicopters. In order to achieve desired results from UAS lidar, mission planning parameters and ground control requirements therefore need to be tailored to data collection from UAS platforms. This paper presents the preliminary results of how a variety control target designs responded to a UAS lidar survey flown along different trajectories at different heights above ground level. This research draws upon previous airborne laser scanning work and aims to provide guidance on considerations for UAS lidar specific ground control targets.</p>

scholarly journals Terrestrial Laser Scanning for Vegetation Analyses with a Special Focus on Savannas

2021 ◽  
Vol 13 (3) ◽  
pp. 507
Author(s):  
Tasiyiwa Priscilla Muumbe ◽  
Jussi Baade ◽  
Jenia Singh ◽  
Christiane Schmullius ◽  
Christian Thau
Keyword(s):  
Remote Sensing ◽  
Vegetation Structure ◽  
Laser Scanning ◽  
Spatial Scales ◽  
Terrestrial Laser Scanning ◽  
Point Clouds ◽  
Parameter Extraction ◽  
Airborne Lidar ◽  
Special Focus ◽  
Vegetation Parameter

Savannas are heterogeneous ecosystems, composed of varied spatial combinations and proportions of woody and herbaceous vegetation. Most field-based inventory and remote sensing methods fail to account for the lower stratum vegetation (i.e., shrubs and grasses), and are thus underrepresenting the carbon storage potential of savanna ecosystems. For detailed analyses at the local scale, Terrestrial Laser Scanning (TLS) has proven to be a promising remote sensing technology over the past decade. Accordingly, several review articles already exist on the use of TLS for characterizing 3D vegetation structure. However, a gap exists on the spatial concentrations of TLS studies according to biome for accurate vegetation structure estimation. A comprehensive review was conducted through a meta-analysis of 113 relevant research articles using 18 attributes. The review covered a range of aspects, including the global distribution of TLS studies, parameters retrieved from TLS point clouds and retrieval methods. The review also examined the relationship between the TLS retrieval method and the overall accuracy in parameter extraction. To date, TLS has mainly been used to characterize vegetation in temperate, boreal/taiga and tropical forests, with only little emphasis on savannas. TLS studies in the savanna focused on the extraction of very few vegetation parameters (e.g., DBH and height) and did not consider the shrub contribution to the overall Above Ground Biomass (AGB). Future work should therefore focus on developing new and adjusting existing algorithms for vegetation parameter extraction in the savanna biome, improving predictive AGB models through 3D reconstructions of savanna trees and shrubs as well as quantifying AGB change through the application of multi-temporal TLS. The integration of data from various sources and platforms e.g., TLS with airborne LiDAR is recommended for improved vegetation parameter extraction (including AGB) at larger spatial scales. The review highlights the huge potential of TLS for accurate savanna vegetation extraction by discussing TLS opportunities, challenges and potential future research in the savanna biome.

scholarly journals An Adaptive Surface Interpolation Filter Using Cloth Simulation and Relief Amplitude for Airborne Laser Scanning Data

2021 ◽  
Vol 13 (15) ◽  
pp. 2938
Author(s):  
Feng Li ◽  
Haihong Zhu ◽  
Zhenwei Luo ◽  
Hang Shen ◽  
Lin Li
Keyword(s):  
Laser Scanning ◽  
Point Clouds ◽  
Airborne Laser Scanning ◽  
Superior Performance ◽  
Cloth Simulation ◽  
Cloud Data ◽  
Interpolation Filter ◽  
Landscape Characteristics ◽  
Surface Interpolation ◽  
Airborne Laser

Separating point clouds into ground and nonground points is an essential step in the processing of airborne laser scanning (ALS) data for various applications. Interpolation-based filtering algorithms have been commonly used for filtering ALS point cloud data. However, most conventional interpolation-based algorithms have exhibited a drawback in terms of retaining abrupt terrain characteristics, resulting in poor algorithmic precision in these regions. To overcome this drawback, this paper proposes an improved adaptive surface interpolation filter with a multilevel hierarchy by using a cloth simulation and relief amplitude. This method uses three hierarchy levels of provisional digital elevation model (DEM) raster surfaces with thin plate spline (TPS) interpolation to separate ground points from unclassified points based on adaptive residual thresholds. A cloth simulation algorithm is adopted to generate sufficient effective initial ground seeds for constructing topographic surfaces with high quality. Residual thresholds are adaptively constructed by the relief amplitude of the examined area to capture complex landscape characteristics during the classification process. Fifteen samples from the International Society for Photogrammetry and Remote Sensing (ISPRS) commission are used to assess the performance of the proposed algorithm. The experimental results indicate that the proposed method can produce satisfying results in both flat areas and steep areas. In a comparison with other approaches, this method demonstrates its superior performance in terms of filtering results with the lowest omission error rate; in particular, the proposed approach retains discontinuous terrain features with steep slopes and terraces.

scholarly journals Regional Modeling of Forest Fuels and Structural Attributes Using Airborne Laser Scanning Data in Oregon

2021 ◽  
Vol 13 (2) ◽  
pp. 261
Author(s):  
Francisco Mauro ◽  
Andrew T. Hudak ◽  
Patrick A. Fekety ◽  
Bryce Frank ◽  
Hailemariam Temesgen ◽  
...  
Keyword(s):  
Point Cloud ◽  
Laser Scanning ◽  
Field Measurements ◽  
Point Clouds ◽  
Semiparametric Models ◽  
Airborne Laser Scanning ◽  
Parametric Models ◽  
Fuel Load ◽  
Forest Fuels ◽  
Airborne Laser

Airborne laser scanning (ALS) acquisitions provide piecemeal coverage across the western US, as collections are organized by local managers of individual project areas. In this study, we analyze different factors that can contribute to developing a regional strategy to use information from completed ALS data acquisitions and develop maps of multiple forest attributes in new ALS project areas in a rapid manner. This study is located in Oregon, USA, and analyzes six forest structural attributes for differences between: (1) synthetic (i.e., not-calibrated), and calibrated predictions, (2) parametric linear and semiparametric models, and (3) models developed with predictors computed for point clouds enclosed in the areas where field measurements were taken, i.e., “point-cloud predictors”, and models developed using predictors extracted from pre-rasterized layers, i.e., “rasterized predictors”. Forest structural attributes under consideration are aboveground biomass, downed woody biomass, canopy bulk density, canopy height, canopy base height, and canopy fuel load. Results from our study indicate that semiparametric models perform better than parametric models if no calibration is performed. However, the effect of the calibration is substantial in reducing the bias of parametric models but minimal for the semiparametric models and, once calibrations are performed, differences between parametric and semiparametric models become negligible for all responses. In addition, minimal differences between models using point-cloud predictors and models using rasterized predictors were found. We conclude that the approach that applies semiparametric models and rasterized predictors, which represents the easiest workflow and leads to the most rapid results, is justified with little loss in accuracy or precision even if no calibration is performed.

scholarly journals Highway alignments extraction and 3D modeling from airborne laser scanning point clouds

2021 ◽  
Vol 102 ◽  
pp. 102429
Author(s):  
Yuzhou Zhou ◽  
Ronggang Huang ◽  
Tengping Jiang ◽  
Zhen Dong ◽  
Bisheng Yang
Keyword(s):  
3D Modeling ◽  
Laser Scanning ◽  
Point Clouds ◽  
Airborne Laser Scanning ◽  
Airborne Laser

Using LiDAR Point Clouds in Determination of the Scots Pine Stands Spatial Structure Meaning in the Conservation of Lichen Communities in “Bory Tucholskie” National Park

2019 ◽  
Vol 31 (1) ◽  
pp. 85-103
Author(s):  
Piotr Wężyk ◽  
Paweł Hawryło ◽  
Marta Szostak ◽  
Karolina Zięba-Kulawik ◽  
Monika Winczek ◽  
...  
Keyword(s):  
Spatial Structure ◽  
National Park ◽  
Laser Scanning ◽  
Ground Level ◽  
Point Clouds ◽  
Organic Layer ◽  
Active Protection ◽  
Scanning Lidar ◽  
Pine Stands ◽  
Biometric Features

Abstract The aim of the research carried out in 2018 and financed by the Forest Fund was the analysis of biometric features and parameters of pine stands in the area of the “Bory Tucholskie” National Park (PNBT), where a program of active protection of lichen was initiated in 2017. Environmental analyses were conducted in relation to selected biometric features of trees and stands using laser scanning (LiDAR), including ULS (Unmanned Laser Scanning; RIEGL VUX-1) and TLS (Terrestrial Laser Scanning; FARO FOCUS 3D; X130). Thanks to the application of LiDAR technology, the structure of pine stands was precisely determined by means of a series of descriptive statistics characterizing the 3D spatial structure of vegetation. Using the Trees Crown Model (CHM), the analysis of the volume of tree crowns and the volume of space under canopy was performed. For the analysed sub-compartments, GIS solar analyses were carried out for the solar energy reaching the canopy and the ground level due to active protection of lichen. Multispectral photos were obtained using a specialized RedEdge-M camera (MicaSense) mounted on the UAV multi rotor platform Typhoon H520 (Yuneec). Flights with a thermal camera were also performed in order to detect places on the ground with high temperature. Plant indices: NDVI, NDRE, GNDVI and GRVI were also calculated for sub-compartments. The data obtained in 2017 and 2018 were the basis for spatial and temporal analyses of 4-D changes in stands which were related to the removal of some trees and organic layer (litter, moss layer).

scholarly journals Accuracy Assessment of Point Clouds from LiDAR and Dense Image Matching Acquired Using the UAV Platform for DTM Creation

2018 ◽  
Vol 7 (9) ◽  
pp. 342 ◽  
Author(s):  
Adam Salach ◽  
Krzysztof Bakuła ◽  
Magdalena Pilarska ◽  
Wojciech Ostrowski ◽  
Konrad Górski ◽  
...  
Keyword(s):  
Land Cover ◽  
Laser Scanning ◽  
Point Clouds ◽  
Data Sources ◽  
Digital Terrain Models ◽  
Vegetation Height ◽  
Digital Terrain ◽  
Terrain Models ◽  
Airborne Laser ◽  
Vertical Accuracy

In this paper, the results of an experiment about the vertical accuracy of generated digital terrain models were assessed. The created models were based on two techniques: LiDAR and photogrammetry. The data were acquired using an ultralight laser scanner, which was dedicated to Unmanned Aerial Vehicle (UAV) platforms that provide very dense point clouds (180 points per square meter), and an RGB digital camera that collects data at very high resolution (a ground sampling distance of 2 cm). The vertical error of the digital terrain models (DTMs) was evaluated based on the surveying data measured in the field and compared to airborne laser scanning collected with a manned plane. The data were acquired in summer during a corridor flight mission over levees and their surroundings, where various types of land cover were observed. The experiment results showed unequivocally, that the terrain models obtained using LiDAR technology were more accurate. An attempt to assess the accuracy and possibilities of penetration of the point cloud from the image-based approach, whilst referring to various types of land cover, was conducted based on Real Time Kinematic Global Navigation Satellite System (GNSS-RTK) measurements and was compared to archival airborne laser scanning data. The vertical accuracy of DTM was evaluated for uncovered and vegetation areas separately, providing information about the influence of the vegetation height on the results of the bare ground extraction and DTM generation. In uncovered and low vegetation areas (0–20 cm), the vertical accuracies of digital terrain models generated from different data sources were quite similar: for the UAV Laser Scanning (ULS) data, the RMSE was 0.11 m, and for the image-based data collected using the UAV platform, it was 0.14 m, whereas for medium vegetation (higher than 60 cm), the RMSE from these two data sources were 0.11 m and 0.36 m, respectively. A decrease in the accuracy of 0.10 m, for every 20 cm of vegetation height, was observed for photogrammetric data; and such a dependency was not noticed in the case of models created from the ULS data.

Sign in / Sign up

Export Citation Format

Share Document