scholarly journals Copper Molarity Effect on the Optical Properties of Cu2CdSnS4 Quaternary Thin Films

2021 ◽  
pp. 1513-1523
Author(s):  
Shaymaa Khashea Abdo ◽  
Jamal M. Rzaij
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Absorption Coefficient ◽  
Absorption Edge ◽  
Energy Gap ◽  
Spray Pyrolysis Technique ◽  
Visible Range ◽  
Chemical Spray Pyrolysis ◽  
Copper Solution ◽  
Average Grain Size

 The quaternary alloy of Cu2CdSnS4 (CCSS) is one type of thin film materials that contributes to the field of photovoltaic devices manufacturing, the importance of which has not been commonly enlightened as most of the other materials. For the preparation of CCSS thin films at 350 °C on glass substrates, the chemical spray pyrolysis technique was used. The optical properties of thin films prepared under the influence of the variation of copper solution molarity (0.03, 0.05, 0.07, and 0.09 M) on the quaternary compound were examined using a UV-vis spectrophotometer. The findings of the AFM study showed the atoms on the surface that are acclimatized in the form of nanorods with an increase in the average grain size from 62.72 to 79.17 nm. The results also showed an improvement in the average surface roughness from 5.69 to 12.8 nm when copper concentration increased from 0.03 to 0.09 M. The UV-vis results showed that the optical transmittance of CCSS decreases by increasing the solution molarity of copper, with a change in the absorption edge toward the low energy side (redshift). With an increase in the wavelength between 725 and 960 nm, a low absorption coefficient was found in the infrared region, while a strong absorption coefficient in the visible range was observed with the increase in copper solution molarity. The energy gap values decreased from 1.6 to 1.47 eV when copper solution molarity increased from 0.03 to 0.09 M. By raising copper solution molarity to 0.09 M, the refractive index at the absorption edge was increased from 1.6 to 1.97, while the extinction coefficient reduced.

scholarly journals Effects of Non-Thermal Argon Plasma Produced at Atmospheric Pressure on the Optical Properties of CdO Thin Films

2018 ◽  
Vol 15 (2) ◽  
pp. 221-226
Author(s):  
Baghdad Science Journal
Keyword(s):  
Thin Films ◽  
Dielectric Constant ◽  
Optical Properties ◽  
Absorption Coefficient ◽  
Extinction Coefficient ◽  
Energy Gap ◽  
Cadmium Oxide ◽  
Argon Plasma ◽  
Chemical Spray Pyrolysis ◽  
Cdo Thin Films

In this paper the effect of nonthermal atmospheric argon plasma on the optical properties of the cadmium oxide CdO thin films prepared by chemical spray pyrolysis was studied. The prepared films were exposed to different time intervals (0, 5, 10, 15, 20) min. For every sample, the transmittance, Absorbance, absorption coefficient, energy gap, extinction coefficient and dielectric constant were studied. It is found that the transmittance and the energy gap increased with exposure time, and absorption. Absorption coefficient, extinction coefficient, dielectric constant decreased with time of exposure to the argon plasma

scholarly journals Effect of Manganese Contain on the Optical Properties of CuO Thin Films

2016 ◽  
Vol 65 ◽  
pp. 37-42
Author(s):  
Wasmaa Abdulsattar Jabbar
Keyword(s):  
Thin Films ◽  
Refractive Index ◽  
Optical Properties ◽  
Absorption Coefficient ◽  
Copper Oxide ◽  
Extinction Coefficient ◽  
Energy Gap ◽  
Chemical Spray Pyrolysis ◽  
Chemical Spray ◽  
Uv Visible

Copper oxide prepared with various contains of Manganese by chemical spray pyrolysis. Some optical properties are studied from recording the absorption spectra via UV-Visible spectrophotometer in the range of 460-900 nm. The absorbance increased with increasing Mn-contain in the CuO thin films, and the absorption coefficient. Extinction coefficient and refractive index are decreased with increasing Mn-contain in the CuO thin films, also the energy gap shifted from 2 eV to 1.91 eV after 4%Mn additive.

scholarly journals Effects of Cu-Doping on Optical Properties of NiO

2015 ◽  
Vol 48 ◽  
pp. 155-162 ◽  
Author(s):  
Nidhal Nissan Jandow
Keyword(s):  
Thin Film ◽  
Optical Properties ◽  
Absorption Coefficient ◽  
Extinction Coefficient ◽  
Energy Gap ◽  
Spray Pyrolysis Technique ◽  
Skin Depth ◽  
Cu Doping ◽  
Uv Visible ◽  
Absorbance Spectra

This work presents the effect of Cu-doping on some optical properties of Cu:NiO thin film prepared by spray pyrolysis technique. UV-Visible spectrophotometer in the range 380-900 nm used to determine the absorbance spectra for various Cu-doping of Cu:NiO thin film. The transmittance and energy gap are decreased with increasing Cu-doping in the prepared films, while absorption coefficient, extinction coefficient, and skin depth are increased with increasing Cu-doping.

scholarly journals A Study of the Structural and Optical Properties of SnS:F prepared by chemical spray pyrolysis technique

2014 ◽  
Vol 11 (2) ◽  
pp. 518-526
Author(s):  
Baghdad Science Journal
Keyword(s):  
Optical Properties ◽  
Spray Pyrolysis ◽  
Energy Gap ◽  
Spray Pyrolysis Technique ◽  
Chemical Spray Pyrolysis ◽  
Structural And Optical Properties ◽  
Optical Energy Gap ◽  
Optical Energy ◽  
Chemical Spray Pyrolysis Technique ◽  
Chemical Spray

Thin films of pure tin mono-sulfide SnS and tin mono-sulfide for (1,2,3,4)% fluorine SnS:F with Thicknesses of (0.85 ±0.05) ?m and (0.45±0.05) ?m respectively were prepared by chemical spray pyrolysis technique. the effect of doping of F on structural and optical properties has been studied. X-Ray diffraction analysis showed that the prepared films were polycrystalline with orthorhombic structure. It was found that doping increased the intensity of diffraction peaks. Optical properties of all samples were studied by recording the absorption and transmission spectrum in range of wave lengths (300-900) nm. The optical energy gap for direct forbidden transition and indirect allowed transition were evaluated It is found that for doping less than 2% the optical energy gap increases as the percentage of doping increases in the samples while for doping more than 2% the values of the optical energy gap decreases as the percentage of doping increases.

scholarly journals Annealing Effect on Some Optical Properties of Cr2O3 Thin Films Prepared by Spray Pyrolysis Technique

2011 ◽  
Vol 8 (2) ◽  
pp. 561-565
Author(s):  
Baghdad Science Journal
Keyword(s):  
Thin Films ◽  
Dielectric Constant ◽  
Refractive Index ◽  
Optical Properties ◽  
Absorption Coefficient ◽  
Spray Pyrolysis ◽  
Annealing Temperature ◽  
Spray Pyrolysis Technique ◽  
Annealing Effect ◽  
Before And After

Cr2O3 thin films have been prepared by spray pyrolysis on a glass substrate. Absorbance and transmittance spectra were recorded in the wavelength range (300-900) nm before and after annealing. The effects of annealing temperature on absorption coefficient, refractive index, extinction coefficient, real and imaginary parts of dielectric constant and optical conductivity were expected. It was found that all these parameters increase as the annealing temperature increased to 550°C.

scholarly journals optical proprties of poly crystaline CdS thin films

2005 ◽  
Vol 2 (2) ◽  
pp. 231-235
Author(s):  
Baghdad Science Journal
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Absorption Coefficient ◽  
Energy Gap ◽  
Glass Temperature ◽  
Calculated Energy ◽  
Cds Thin Films ◽  
Temperature Preparation

Studied the optical properties of the membranes CdS thin containing different ratios of ions cadmium to sulfur attended models manner spraying chemical gases on the rules of the glass temperature preparation (350c) were calculated energy gap allowed direct these membranes as observed decrease in the value of the energy gap at reducing the proportion ofsulfur ions as absorption coefficient was calculated

EFFECT OF SUBSTRATE TEMPERATURE ON THE STRUCTURAL AND OPTICAL PROPERTIES OF NiTsPc THIN FILMS

2019 ◽  
Vol 27 (03) ◽  
pp. 1950124 ◽  
Author(s):  
MOHAMMED YARUB HANI ◽  
ADDNAN H. AL-AARAJIY ◽  
AHMED M. ABDUL-LETTIF
Keyword(s):  
Thin Films ◽  
Grain Size ◽  
Optical Properties ◽  
Substrate Temperature ◽  
Energy Gap ◽  
Chemical Spray Pyrolysis ◽  
Structural And Optical Properties ◽  
Absorption Bands ◽  
Tauc Plot ◽  
Substrate Temperatures

Nickel(II) phthalocyanine-tetrasulfonic acid tetrasodium salt (NiTsPc) thin films were deposited on glass substrates at different substrate temperatures ([Formula: see text]) by chemical spray pyrolysis (CSP) technique. The substrate temperature varied from 110∘C to 310∘C in 50∘C steps. The substrate surface temperature is the main parameter that determines the film morphology and properties of the thin films. The structural properties of the deposited NiTsPc thin films were investigated by X-ray diffraction (XRD) and from the obtained results, it was shown that depositing thin films using 210∘C as [Formula: see text] results in higher crystallinity. Atomic force microscope (AFM) was employed to obtain the surface topography and to calculate the roughness and grain size. The smoothest thin film surface was obtained when using at 160∘C, while the highest roughness was obtained at 310∘C. The optical properties were investigated by ultraviolet visible (UV-Vis) spectrophotometer and fluorescence spectrophotometer. From the absorption spectra recorded in the wavelength range 190–1100[Formula: see text]nm, two absorption bands were observed, which are known as Soret and Q-band. By observing the absorption spectrum, it can be concluded that the deposited thin films at 110∘C–310∘C have direct energy gap. From Tauc plot relation, the energy gap ([Formula: see text]) was calculated. The values of the energy gap were between 3.05 and 3.14[Formula: see text]eV. It was observed that different [Formula: see text] highly affects the structural and optical properties of the deposited thin films. The crystallinity, grain size, roughness and the optical properties were strongly affected by the different substrate temperatures.

scholarly journals Influence of Annealing on Properties of Spray Deposited ZnO Thin Films

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Kalyani Nadarajah ◽  
Ching Yern Chee ◽  
Chou Yong Tan
Keyword(s):  
Thin Films ◽  
Electrical Resistivity ◽  
Spray Pyrolysis Technique ◽  
Hexagonal Wurtzite Structure ◽  
Ambient Air ◽  
Zno Thin Films ◽  
Visible Range ◽  
X Ray ◽  
Average Grain Size ◽  
Vis Spectroscopy

Zinc Oxide (ZnO) thin films were deposited on glass substrates via the spray pyrolysis technique. The films were subsequently annealed in ambient air from 300°C to 500°C. The morphology and structural properties of the thin films were studied by field emission scanning electron microscope (FESEM), atomic force microscopy (AFM), and X-ray diffractometry (XRD) techniques. Electrical resistivity of the thin films was measured using a data acquisition unit. The optical properties of the films were characterized by UV-vis spectroscopy and photoluminescence (PL) technique. X-ray diffraction data showed that the films were grown in the (002) direction with a hexagonal wurtzite structure. The average grain size ranged from 15 to 27 nm. Increasing annealing temperatures resulted in larger grain sizes and higher crystallinity, with the surface roughness of annealed films being more than twice if compared to unannealed film. The electrical resistivity of the films decreased with the increasing annealing temperature. The UV and visible band emissions were observed in the photoluminescence spectra, due to exciton and defect-related emissions, respectively. The transmission values of the films were as high as 90% within the visible range (400–700 nm).

scholarly journals Synthesis and characterization of Eu3+ doped TiO2 thin films deposited by spray pyrolysis technique for photocatalytic application

2020 ◽  
Author(s):  
Shereen Alshomar
Keyword(s):  
Thin Films ◽  
Methylene Blue ◽  
Refractive Index ◽  
Optical Properties ◽  
Film Thickness ◽  
Photocatalytic Degradation ◽  
Spray Pyrolysis ◽  
Spray Pyrolysis Technique ◽  
Average Grain Size ◽  
Double Beam

Abstract In this study, nanocrystalline TiO 2 : Eu 3+ thin films are successfully formed by spray pyrolysis technique deposited on glass substrate. Optical, electrical, structure, surface morphology, and photocatalytic degradation of Methylene blue have been examined. The optical properties of the films are analyzed using transmittance and reflectance spectra, which are measured using UV-Vis-NIR double-beam spectrophotometer. Optical properties such as refractive index (n), extinction coefficient (k), optical conductivity (σ) and Urbach energy (E u ) have been calculated as a function of Eu 3+ concentration. Film thickness were evaluated using the refractive index dependence on wavelength . The films thickness were determined as 97.13, 122.62, 123.24, 117.14 and 128.25 nm, respectively, for Eu doped TiO 2 at 0,4, 6, 8 and 10 wt % doping concentration. The band gap values raised from 3.29 to 3.42 eV with increasing the Eu 3+ dopant concentration. The highest electrical conductivity was found to be 3.01x10 -2 (Ω.cm) -1 at high doping level with 10 wt% Eu 3+ . The XRD analysis illustrate the tetragonal crystal structure of films with anatase phase and reduces crystallite size linearly with increasing Eu 3+ concentration. Scanning electron microscopy (SEM) analysis indicated consistent allocation of irregular and spherical shaped grains covering the substrate surface. The average grain size in range of 82.5 – 51.1 nm is observed and films show porous nature. The photocatalytic effect of TiO 2 : Eu 3+ thin films is predicted from the degradation of methylene blue (MB) at room temperature under UV light irradiation. An enhancement in photocatalytic degradation observed by increasing the amount of Eu 3+ due to increase in the e/h pair production and increase of film thickness. These results make TiO 2 : Eu 3+ thin films as attractive candidate for photovoltaic cells and other optoelectronic device applications

Sign in / Sign up

Export Citation Format

Share Document