scholarly journals Transmission (2Gbps) over optical fiber cable by using radio over fiber and wavelength division multiplexing techniques

2019 ◽  
Vol 24 (5) ◽  
pp. 115
Author(s):  
Humam Husseinˡ ◽  
Dogu Cagdas Atilla1 ◽  
Essa Essa2 ◽  
Cagatay Aydin1
Keyword(s):  
Optical Fiber ◽  
Wavelength Division Multiplexing ◽  
Performance Test ◽  
Optical Signal ◽  
Radio Over Fiber ◽  
Total Power ◽  
Q Factor ◽  
Wavelength Division ◽  
Fiber Technology ◽  
Optical Fiber Cable

In recent years, there has been a growing and continuous demand for great (data rates) beyond existing wired and wireless networks. Radio-over-Fiber technology is considered as an efficient and practical solution for providing broadband wireless. In this paper, many techniques are used to implement a system that has the capability to provide a great bit rate, broadband bandwidth, and minimum cost. So Radio-over-Fiber technology was used to modulate the light with radio-signal and transmission the signals through an optical fiber cable. Wavelength-Division-Multiplexing technique was used to send many signals through the same link, and Subcarrier Multiplexing-Amplitude Shift keying as a modulation format. 2Gpbs separate on two channels was transmitted on Single-Mode Fiber. The average results obtained from our experience was as follows: maximum Q factor average = 4.9712925, minimum BER average = 3.63*10-7, total power average (dBm) = -51.1502, the OSNR average (dB) = 52.085 for channel_1. The results of channel_2 were: maximum Q factor average = 5.5901325, minimum BER average = 1.26*10-8, total power average (dBm) = -46.60135, the average of optical signal-to-noise ratio (dB) = 54.65. All the average result that has from our simulation was very good and acceptable. The simulation and performance test of our experience was done using Optisystem 7.0.   http://dx.doi.org/10.25130/tjps.24.2019.100

Optical Networks Performance Optimization Based on Hybrid Configurations of Optical Fiber Amplifiers and Optical Receivers

2019 ◽  
Vol 0 (0) ◽  
Author(s):  
I. S. Amiri ◽  
Fatma Mohammed Aref Mahmoud Houssien ◽  
Ahmed Nabih Zaki Rashed ◽  
Abd El-Naser A. Mohammed
Keyword(s):  
Optical Fiber ◽  
Optical Networks ◽  
Wavelength Division Multiplexing ◽  
Performance Optimization ◽  
Input Power ◽  
Fiber Amplifiers ◽  
Q Factor ◽  
Wavelength Division ◽  
Transmission Distance ◽  
Optical Fiber Amplifiers

AbstractThe 16-channels dense wavelength division multiplexing (DWDM) systems have been optimized by utilizing hybrid configurations of conventional optical fiber amplifiers (EDFA, RAMAN and SOA) and optical photodetectors (PIN, APD(Si) and APD(InGaAs)). The DWDM systems were implemented for 5 Gb/s channel speed using one of these configurations with 100 GHz channel spacing and 25 km amplifying section. The hybrid configurations are the combinations of (PIN + EDFA), (PIN + RAMAN), (PIN + SOA), (APD(Si) + EDFA), (APD(Si) + RAMAN), (APD(Si) + SOA), (APD(InGaAs) + EDFA), (APD(InGaAs) + RAMAN) and (APD(InGaAs) + SOA). Based on BER, Q-factor and eye diagrams, the performance was compared for these configurations under influences of various thermal noise levels of photodetectors over different fiber lengths ranging from 25 km up to 150 km. The results revealed that both APD structures give optimum performance at input power Pin = 5 dBm due to high internal avalanche gain. EDFA outperforms RAMAN and SOA amplifiers. SOA amplifier shows degraded performance because of nonlinearity effects induced. RAMAN amplifier seems to be the best alternative for long reach DWDM systems because it minimizes the effects of fiber nonlinearities. The configuration (APD(Si) + EDFA) is the most efficient and recommended to be used for transmission distance beyond 100 km due to its larger Q-factor.

Cascaded stages of parametric optical fiber amplifiers with Raman fiber amplifiers for upgrading of telecommunication networks through optical wireless communication channel

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Mahmoud M.A. Eid ◽  
Eslam Shehata ◽  
Ahmed Nabih Zaki Rashed
Keyword(s):  
Optical Fiber ◽  
Electrical Power ◽  
Optical Power ◽  
Optical Signal ◽  
Electrical Signal ◽  
Telecommunication Networks ◽  
Fiber Amplifiers ◽  
Total Power ◽  
Q Factor ◽  
Power Meter

Abstract This paper contains a main model which concludes a two optical fiber cable along 70 km and with Parametric/Raman amplifiers with a result of total power 0.781 dBm that computed by the optical power meter which is located before the receiver part and the second optical fiber channel, a total power −44.186 dBm at the end of model which is computed by the electrical power meter visualizer, and a max. Q factor 2.548 computed by the BER analyzer. The suggested model has outlined some updates on the previous model to improve the results so that the results are increased at the same length as the following: total power of optical signal becomes 10.039 dBm, total power of electrical signal becomes 0.624 dBm, and the max. Q factor becomes 9.60787.

Performance Analysis of NRZ and RZ Modulation Schemes in Optical Fiber Link Using EDFA

2017 ◽  
Vol 7 (8) ◽  
pp. 161 ◽  
Author(s):  
. Payal ◽  
Suresh Kumar ◽  
Deepak Sharma
Keyword(s):  
Optical Fiber ◽  
Wavelength Division Multiplexing ◽  
Communication System ◽  
Optical Fiber Communication ◽  
Q Factor ◽  
Modulation Formats ◽  
Wavelength Division ◽  
Advantages And Disadvantages ◽  
Area Of Interest ◽  
Fiber Link

Dense Wavelength Division Multiplexing (DWDM) is the current area of interest to exploit the bandwidth offered by optical fiber to enhance the data rate requirements. In the present paper analysis of DWDM system using Erbium Doped Fiber Amplifier (EDFA) is carried out in C-band. The 32-channel Wavelength Division Multiplexing (WDM) system, with a high-performanceflowrate of 10 Gbps, has been evaluated. The performance of Return to Zero (RZ) and Non-Return to Zero (NRZ) modulation formats in an optical communication system are investigated by modeling an optical fiber link using software OPTISYS V14. According to the modulated outputs, a comprehensive comparison in terms of Q factor is developed to establish the advantages and disadvantages of the code formats NRZ and RZ in short and long haul optical fiber communication system. Optimum results of Bit Error Rate (BER) and Q-factor are obtained for 60, 80 and 100km of fiber length. Pumping is discussed at 980nm and 1480nm.

Cost Efficient 4 × 2.5 Gb/s Transparent WDM Ring Network using DML and MetroCor Fiber for Long Reach Applications

2019 ◽  
Vol 40 (1) ◽  
pp. 67-73 ◽  
Author(s):  
Anu Sheetal ◽  
Harjit Singh
Keyword(s):  
Wavelength Division Multiplexing ◽  
Signal To Noise Ratio ◽  
Cost Effective ◽  
Optical Signal ◽  
Network Node ◽  
Q Factor ◽  
Ring Network ◽  
Power Requirement ◽  
Wavelength Division ◽  
Cost Efficient

Abstract In this paper, we analyze the performance of the 4 × 2.5 Gb/s wavelength division multiplexing (WDM) transparent metro ring network comprising of one network node and eight access nodes. Here, the power requirement of 360 km ring network has been evaluated using the optical signal to noise ratio (OSNR), Q-factor, inter-symbol interference (ISI) and power penalty. The metro network utilized the cost-effective directly modulated laser (DML) and a negative dispersion fiber called MetroCor in order to give enhanced performance in terms of Q-factor. The power requirement of the network is optimized for the signals over SMF-28 and MetroCor fibers. Also, the comparison is drawn between uncompensated and compensated (with -post and -symmetrical) SMF-28 fibers in the metro environment. The excellent value of Q-factor is obtained at all the nodes. Also, the results show higher OSNR values in the metro environment. Although, smaller power penalties are detected for nodes closer to the network node, but distant nodes require higher power for better transmission.

Performance enhancement of Raman + EYDFA HOA for UD-WDM system applications

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Anurupa Lubana ◽  
Sanmukh Kaur ◽  
Yugnanda Malhotra
Keyword(s):  
Wavelength Division Multiplexing ◽  
Performance Enhancement ◽  
Optical Amplifier ◽  
Q Factor ◽  
Channel Spacing ◽  
Average Gain ◽  
Wavelength Division ◽  
System Parameters ◽  
Gain Variation ◽  
Hybrid Optical Amplifier

AbstractIn this work, we study and analyze the performance of Raman + Erbium-Ytterbium codoped fiber hybrid optical amplifier (HOA) for an ultradense wavelength division multiplexing (UD-WDM) system having 100 channels. The system has been investigated considering initial values of channel spacing and data rate of 0.1 nm (12.5 GHz) and 100 GB/s, respectively. Initially, the two important WDM system parameters—wavelength and channel spacing—have been selected and then optimization of the proposed HOA has been performed in terms of EYDFA length, pump power and Er+ concentration to achieve higher values of average gain, Q-factor and lower gain variation ratio. The optimized configuration of the HOA results in the achievement of higher value of average gain, Q-factor and gain variation ratio of 47 dB, 14 and 0.14, respectively, which confirms its viability for UD-WDM system applications.

8CH AWG Multi/Demultiplexer With MEMS Variable Optical Attenuator

2003 ◽  
Author(s):  
K. Ishikawa ◽  
Q. Yu
Keyword(s):  
Wavelength Division Multiplexing ◽  
Optical Signal ◽  
Arrayed Waveguide Grating ◽  
Optical Contrast ◽  
Network Systems ◽  
Micro Electro Mechanical Systems ◽  
Wavelength Division ◽  
Power Intensity ◽  
Variable Optical Attenuator ◽  
Arrayed Waveguide

An integrated arrayed waveguide grating multi/demultiplexer (AWG) with a micro-electro-mechanical systems (MEMS) based variable optical attenuator (VOA) is reported. The device consists of an AWG based on silica and a MEMS-VOA chip. The MEMS chip includes 100 μm × 100 μm polysilicon shutter plates coated with gold and electrostatic comb-drive actuators. The MEMS chip is interposed in a trench located in the middle of the I/O waveguides of the AWG to tune the optical transmitting power intensity through the waveguides continuously. The MEMS-VOA shutters have more than a 10 μm displacement. Using those shutters, 30 dB optical contrast from 5 dB at the transmit state to 35 dB at the isolation state is achieved. The obtained attenuation contrast is greater than that of a conventional waveguide-based Mach-Zehnder interferometer VOA and sufficient to adjust and equalize the optical signal power in the wavelength division multiplexing (WDM) network systems.

scholarly journals ANALISIS KOMPENSASI DISPERSI MENGGUNAKAN PENGUAT RAMAN PADA JARINGAN WDM (WAVELENGTH DIVISION MULTIPLEXING) DALAM KOMUNIKASI SERAT OPTIK

2018 ◽  
Vol 15 (2) ◽  
pp. 88
Author(s):  
Roby Ikhsan ◽  
Romi Fadli Syahputra ◽  
Saktioto Saktioto
Keyword(s):  
Optical Fiber ◽  
Wavelength Division Multiplexing ◽  
Data Transmission ◽  
Dispersion Compensation ◽  
Optical Fiber Communication ◽  
Fiber Communication ◽  
Wavelength Division ◽  
Fiber Raman Amplifier ◽  
Wdm Network ◽  
Transmission Speed

The discovery of optical fiber cause widespread revolution of communication system. Optical fiber communication has excellency on data transmission speed, security, flexibility, and broadly bandwidth. The applying of WDM network can broaden the bandwidth so that the transmission performance becomes more splendid. Although some factors such as dispersion, attenuation, and scattering can hinder the performance of fiber optic on sending data. Moreover dispersion can wreck data and spread pulse as it travels alongs fiber so that causing interference. There is some methods  of dispersion compensation. In this paper, Fiber Raman Amplifier is used on WDM network to strengthen signal which is sent to detector. This research utilize simulation approachment  with various bandwidth and length fiber. The results show lowest BER value and highest Q-factor at bandwidth frequency of 30 GHz and fiber length of 20 km.

scholarly journals Optical Fiber Amplifiers and Their Applications. Hybrid Er-Doped Fiber Amplifiers for Wavelength-Division Multiplexing Transmission Systems.

1997 ◽  
Vol 25 (2) ◽  
pp. 158-163
Author(s):  
Motoki KAKUI ◽  
Tomonori KASHIWADA ◽  
Koji NAKAZATO ◽  
Masashi ONISHI ◽  
Masayuki SHIGEMATSU ◽  
...  
Keyword(s):  
Optical Fiber ◽  
Wavelength Division Multiplexing ◽  
Fiber Amplifiers ◽  
Transmission Systems ◽  
Wavelength Division ◽  
Optical Fiber Amplifiers ◽  
Er Doped
Sign in / Sign up

Export Citation Format

Share Document