Correction: Effect of Leading Edge Serrations on Dynamic Stall at Rec=30,000

2019 ◽  
Author(s):  
Suganthi Selvaraj ◽  
Anupam Sharma
Keyword(s):  
Leading Edge ◽  
Dynamic Stall ◽  
Correction Effect

The aerodynamics of revolving wings I. Model hawkmoth wings

2002 ◽  
Vol 205 (11) ◽  
pp. 1547-1564 ◽  
Author(s):  
James R. Usherwood ◽  
Charles P. Ellington
Keyword(s):  
Insect Flight ◽  
Leading Edge ◽  
Dynamic Stall ◽  
Leading Edge Vortex ◽  
Force Coefficients ◽  
Attached Flow ◽  
Edge Vortex ◽  
Drag And Lift ◽  
Geometric Relationship ◽  
Spanwise Flow

SUMMARYRecent work on flapping hawkmoth models has demonstrated the importance of a spiral `leading-edge vortex' created by dynamic stall, and maintained by some aspect of spanwise flow, for creating the lift required during flight. This study uses propeller models to investigate further the forces acting on model hawkmoth wings in `propeller-like' rotation (`revolution'). Steadily revolving model hawkmoth wings produce high vertical (≈ lift) and horizontal (≈ profile drag) force coefficients because of the presence of a leading-edge vortex. Both horizontal and vertical forces, at relevant angles of attack, are dominated by the pressure difference between the upper and lower surfaces; separation at the leading edge prevents `leading-edge suction'. This allows a simple geometric relationship between vertical and horizontal forces and the geometric angle of attack to be derived for thin, flat wings. Force coefficients are remarkably unaffected by considerable variations in leading-edge detail, twist and camber. Traditional accounts of the adaptive functions of twist and camber are based on conventional attached-flow aerodynamics and are not supported. Attempts to derive conventional profile drag and lift coefficients from `steady' propeller coefficients are relatively successful for angles of incidence up to 50° and, hence, for the angles normally applicable to insect flight.

scholarly journals Force and flowfield measurements to understand unsteady aerodynamics of cycloidal rotors in hover at ultra-low Reynolds numbers

2019 ◽  
Vol 11 ◽  
pp. 175682931983367
Author(s):  
Carolyn M Reed ◽  
David A Coleman ◽  
Moble Benedict
Keyword(s):  
Separation Bubble ◽  
Fluid Dynamic ◽  
Unsteady Aerodynamics ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Dynamic Stall ◽  
Static Case ◽  
Low Reynolds Numbers ◽  
Curvature Effects ◽  
Low Reynolds

This paper provides a fundamental understanding of the unsteady fluid-dynamic phenomena on a cycloidal rotor blade operating at ultra-low Reynolds numbers (Re ∼ 18,000) by utilizing a combination of instantaneous blade force and flowfield measurements. The dynamic blade force coefficients were almost double the static ones, indicating the role of dynamic stall. For the dynamic case, the blade lift monotonically increased up to ±45° pitch amplitude; however, for the static case, the flow separated from the leading edge after around 15° with a large laminar separation bubble. There was significant asymmetry in the lift and drag coefficients between the upper and lower halves of the trajectory due to the flow curvature effects (virtual camber). The particle image velocimetry measured flowfield showed the dynamic stall process during the upper half to be significantly different from the lower half because of the reversal of dynamic virtual camber. Even at such low Reynolds numbers, the pressure forces, as opposed to viscous forces, were found to be dominant on the cyclorotor blade. The power required for rotation (rather than pitching power) dominated the total blade power.

scholarly journals Inflatable Leading Edge-Based Dynamic Stall Control considering Fluid-Structure Interaction

2020 ◽  
Vol 2020 ◽  
pp. 1-28
Author(s):  
Shi-Long Xing ◽  
He-Yong Xu ◽  
Ming-Sheng Ma ◽  
Zheng-Yin Ye
Keyword(s):  
Lift Coefficient ◽  
Fluid Structure Interaction ◽  
Leading Edge ◽  
Dynamic Stall ◽  
Elastic Membrane ◽  
Radius Of Curvature ◽  
Structural Dynamic ◽  
Fluid Structure ◽  
Structure Interaction ◽  
Stall Control

The inflatable leading edge (ILE) is explored as a dynamic stall control concept. A fluid-structure interaction (FSI) numerical method for the elastic membrane structure is constructed based on unsteady Reynolds-averaged Navier-Stokes (URANS) and a mass-spring-damper (MSD) structural dynamic model. Radial basis function- (RBF-) based mesh deformation algorithm and Laplacian and optimization-based mesh smoothing algorithm are adopted in flowfield simulations to achieve the pitching oscillation of the airfoil and to ensure the mesh quality. An airfoil is considered at a freestream Mach number of 0.3 and chord-based Reynolds number of 3.92×106. The airfoil is pitched about its quarter-chord axis at a sinusoidal motion. The numerical results indicate that the ILE can change the radius of curvature of the airfoil leading edge, which could reduce the streamwise adverse pressure gradient and suppress the formation of dynamic stall vortex (DSV). Although the maximum lift coefficient of the airfoil is slightly reduced during the control process, the maximum drag and pitching moment coefficients of the airfoil are greatly reduced by up to 66% and 75.2%, respectively. The relative position of the ILE has a significant influence on its control effect. The control laws of inflation and deflation also affect the control ability of the ILE.

scholarly journals Modeling the interplay between the shear layer and leading edge suction during dynamic stall

2019 ◽  
Vol 31 (10) ◽  
pp. 107104 ◽  
Author(s):  
Julien Deparday ◽  
Karen Mulleners
Keyword(s):  
Shear Layer ◽  
Leading Edge ◽  
Dynamic Stall

New combinational active control strategy for improving aerodynamic characteristics of airfoil and rotor

2019 ◽  
Vol 234 (4) ◽  
pp. 977-996
Author(s):  
Yi-yang Ma ◽  
Qi-jun Zhao ◽  
Guo-qing Zhao
Keyword(s):  
Flow Control ◽  
Control Strategy ◽  
Active Flow Control ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Synthetic Jet ◽  
Dynamic Stall ◽  
Trailing Edge ◽  
Trailing Edge Flap ◽  
Cfd Method

In order to improve the aerodynamic characteristics of rotor, a new active flow control strategy by combining a synthetic jet actuator and a variable droop leading-edge or a trailing-edge flap has been proposed. Their control effects are numerically investigated by computational fluid dynamics (CFD) method. The validated results indicate that variable droop leading-edge and synthetic jet can suppress the formation of dynamic stall vortex and delay flow separation over rotor airfoil. Compared with the baseline state, Cdmax and Cmmax are significantly reduced. Furthermore, parametric analyses on dynamic stall control of airfoil by the combinational method are conducted, and it indicates that the aerodynamic characteristics of the oscillating rotor airfoil can be significantly improved when the non-dimensional frequency ( k*) of variable droop leading-edge is about 1.0. At last, simulations are conducted for the flow control of rotor by the combinational method. The numerical results indicate that large droop angle of variable droop leading-edge can better reduce the torque coefficient of rotor and the trailing-edge flap has the capability of increasing the thrust of rotor. Also, the synthetic jet could further improve the aerodynamic characteristics of rotor.

Applications of Low-Speed Dynamic-Stall Model to the NREL Airfoils

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
Wanan Sheng ◽  
Roderick A. McD. Galbraith ◽  
Frank N. Coton
Keyword(s):  
Wind Turbine ◽  
Power Level ◽  
Leading Edge ◽  
Dynamic Stall ◽  
State University ◽  
Low Speed ◽  
Helicopter Blades ◽  
Mach Numbers ◽  
The Ohio State University ◽  
Low Sensitivity

National Renewable Energy Laboratory, USA (NREL) airfoils have been specially developed for wind turbine applications, and projected to yield more annual energy without increasing the maximum power level. These airfoils are designed to have a limited maximum lift and relatively low sensitivity to leading-edge roughness. As a result, these airfoils have quite different leading-edge profiles from airfoils applied to helicopter blades, and thus, quite different dynamic-stall characteristics. Unfortunately for wind turbine aerodynamics, the dynamic-stall models in use are still those specially developed and refined for helicopter applications. A good example is the Leishman–Beddoes dynamic-stall model, which is one of the most popular models in wind turbine applications. The consequence is that the application of such dynamic-stall model to low-speed cases can be problematic. Recently, some specific dynamic-stall models have been proposed or tuned for the cases of low Mach numbers, but their universality needs further validation. This paper considers the application of the modified dynamic low-speed stall model of Sheng et al. (“A Modified Dynamic Stall Model for Low Mach Numbers,” 2008, ASME J. Sol. Energy Eng., 130(3), pp. 031013) to the NREL airfoils. The predictions are compared with the data of the NREL airfoils tested at the Ohio State University. The current research has two objectives: to justify the suitability of the low-speed dynamic-stall model, and to provide the relevant parameters for the NREL airfoils.

Sign in / Sign up

Export Citation Format

Share Document