scholarly journals A Comparison Study of Brine Desalination using Direct Contact and Air Gap Membrane Distillation

2019 ◽  
Vol 25 (11) ◽  
pp. 47-54
Author(s):  
Ahmed Shamil Khalaf ◽  
Asrar Abdullah Hassan
Keyword(s):  
Flow Rate ◽  
Direct Contact ◽  
Polyvinylidene Fluoride ◽  
Membrane Distillation ◽  
Air Gap ◽  
Feed Flow Rate ◽  
Permeate Flux ◽  
Air Gap Membrane Distillation ◽  
Flat Sheet ◽  
Feed Temperature

Membrane distillation (MD) is a hopeful desalination technique for brine (salty) water. In this research, Direct Contact Membrane Distillation (DCMD) and  Air Gap Membrane Distillation (AGMD) will be used. The sample used is from Shat Al –Arab water (TDS=2430 mg/l). A polyvinylidene fluoride (PVDF) flat sheet membrane was used as a flat sheet form with a plate and frame cell. Several parameters were studied, such as; operation time, feed temperature, permeate temperature, feed flow rate. The results showed that with time, the flux decreases because of the accumulated fouling and scaling on the membrane surface. Feed temperature and feed flow rate had a positive effect on the permeate flux, while permeate temperature had a reverse effect on permeate flux. It is noticeable that the flux in DCMD is greater than AGMD, at the same conditions. The flux in DCMD is 10.95LMH, and that in AGMD is 7.14 LMH.  In AGMD, the air gap layer made a high resistance. Here the temperature transport reduces in the permeate side of AGMD due to the air gap resistance. The heat needed for AGMD is lower than DCMD, this leads to low permeate flux because the temperature difference between the two sides is very small, so the driving force (vapor pressure) is low.                                                                                               

Performance of Air Gap Membrane Distillation Unit for Water Desalination

2014 ◽  
Author(s):  
Atia E. Khalifa ◽  
Dahiru U. Lawal ◽  
Mohamed A. Antar
Keyword(s):  
Flow Rate ◽  
Membrane Distillation ◽  
Air Gap ◽  
Water Desalination ◽  
Feed Water ◽  
Feed Flow Rate ◽  
Permeate Flux ◽  
Air Gap Membrane Distillation ◽  
Gap Width ◽  
Feed Temperature

Due to water scarcity in the Arabic gulf region, water desalination technologies are considered extremely important. The present work represents a fundamental study on the effect of basic operating and design variables on the flux of an air gap membrane distillation (AGMD) unit for water desalination. The flat sheet, channeled air gap membrane distillation module was designed and manufactured locally. The effect of feed flow rate, feed temperature, coolant water temperature, the air gap width, and the water salinity on the module flux are investigated. Analytical model for heat and mass transfer is used to predict the flux and the model results are compared to the experimental ones. Results showed that the technique has good potential to be used for water desalination. The permeate flux is increased by increasing feed flow rate, feed temperature, decreasing the air gap width, decreasing coolant temperature, and decreasing salinity of feed water. For a given feed flow rate, the width of the air gap and the feed water temperature are found to be the most effective parameters in increasing the distillate flux. Predicting the permeate flux with analytical models for heat and mass transfer showed good agreement with experimental results.

scholarly journals Performance Investigation of O-Ring Vacuum Membrane Distillation Module for Water Desalination

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Adnan Alhathal Alanezi ◽  
H. Abdallah ◽  
E. El-Zanati ◽  
Adnan Ahmad ◽  
Adel O. Sharif
Keyword(s):  
Flow Rate ◽  
Membrane Distillation ◽  
Membrane Module ◽  
Water Desalination ◽  
Feed Flow Rate ◽  
Permeate Flux ◽  
Vacuum Degree ◽  
Flat Sheet ◽  
Vacuum Membrane Distillation ◽  
Feed Temperature

A new O-ring flat sheet membrane module design was used to investigate the performance of Vacuum Membrane Distillation (VMD) for water desalination using two commercial polytetrafluoroethylene (PTFE) and polyvinylidene fluoride (PVDF) flat sheet hydrophobic membranes. The design of the membrane module proved its applicability for achieving a high heat transfer coefficient of the order of 103 (W/m2 K) and a high Reynolds number (Re). VMD experiments were conducted to measure the heat and mass transfer coefficients within the membrane module. The effects of the process parameters, such as the feed temperature, feed flow rate, vacuum degree, and feed concentration, on the permeate flux have been investigated. The feed temperature, feed flow rate, and vacuum degree play an important role in enhancing the performance of the VMD process; therefore, optimizing all of these parameters is the best way to achieve a high permeate flux. The PTFE membrane showed better performance than the PVDF membrane in VMD desalination. The obtained water flux is relatively high compared to that reported in the literature, reaching 43.8 and 52.6 (kg/m2 h) for PVDF and PTFE, respectively. The salt rejection of NaCl was higher than 99% for both membranes.

scholarly journals Performances of air gap and water gap MD desalination modules

2018 ◽  
Vol 13 (1) ◽  
pp. 200-209 ◽  
Author(s):  
Atia E. Khalifa
Keyword(s):  
Specific Energy Consumption ◽  
Membrane Distillation ◽  
Air Gap ◽  
Dominant Factor ◽  
Feed Water ◽  
Permeate Flux ◽  
Hydrophobic Membrane ◽  
Air Gap Membrane Distillation ◽  
Gap Width ◽  
Feed Temperature

Abstract Membrane distillation (MD) is a promising thermally-driven membrane separation technology for water desalination. In MD, water vapor is being separated from the hot feed water solution using a micro-porous hydrophobic membrane, due to the difference in vapor pressures across the membrane. In the present work, experiments are conducted to compare the performance of water gap membrane distillation (WGMD) and air gap membrane distillation (AGMD) modules under the main operating and design conditions including the feed and coolant temperatures, membrane material and pore sizes, and the gap width. Results showed that the WGMD module produced higher fluxes as compared to the AGMD module, for all test conditions. The feed temperature is the dominant factor affecting the system flux. The permeate flux increases with reducing the gap width for both water and air gap modules. However, WGMD module was found to be less sensitive to the change in the gap width compared to the AGMD module. The PTFE membrane produced higher permeate flux as compared to the PVDF membrane. Bigger mean pore diameter enhanced the permeate flux, however, this enhancement is marginal at high feed temperatures. With increasing the feed temperature, the GOR values increase and the specific energy consumption decreases.

Performance evaluation of ePTFE and PVDF flat-sheet module direct contact membrane distillation

2010 ◽  
Vol 62 (2) ◽  
pp. 347-352 ◽  
Author(s):  
Ching-Jung Chuang ◽  
Kuo-Lun Tung ◽  
Yang-Hsiang Fan ◽  
Chii-Dong Ho ◽  
James Huang
Keyword(s):  
Direct Contact ◽  
Polyvinylidene Fluoride ◽  
Membrane Distillation ◽  
Membrane Properties ◽  
Energy Integration ◽  
Permeate Flux ◽  
Increase Energy Efficiency ◽  
Module Design ◽  
Direct Contact Membrane Distillation ◽  
Flat Sheet

This paper reports experiments using a flat-sheet module with 0.18 ∼ 0.45 μm ePTFE (expanded polytetrafluoroethylene) and PVDF (polyvinylidene fluoride) membranes to show the effects of membrane properties, salt concentration and fluid hydrodynamics on the permeate flux and salt rejection of DCMD (direct contact membrane distillation). A theoretical prediction of the permeate flux was carried out, and was in close agreement with the experimental results. In addition, the energy integration of the process was also analyzed in order to evaluate module design to increase energy efficiency. According to the simulated results of the energy integration design, a combination of simultaneous cooling of the permeate stream and an additional heat exchanger to lower the temperature of the permeate stream not only enhances the MD flux, but also reduces energy consumption.

scholarly journals A Systematic Framework for Optimizing a Sweeping Gas Membrane Distillation (SGMD)

Membranes ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 254
Author(s):  
Nawras N. Safi ◽  
Salah. S. Ibrahim ◽  
Nasser Zouli ◽  
Hasan Shaker Majdi ◽  
Qusay F. Alsalhy ◽  
...  
Keyword(s):  
Flow Rate ◽  
Gas Flow ◽  
Membrane Distillation ◽  
Feed Flow Rate ◽  
Permeate Flux ◽  
Gas Flow Rate ◽  
Feed Concentration ◽  
Sweeping Gas ◽  
Feed Temperature ◽  
Systematic Framework

The present work has undertaken a meticulous glance on optimizing the performance of an SGMD configuration utilized a porous poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-co-HFP) membrane. This was carried out by conducting a systematic framework for investigating and optimizing the pertinent parameters such as sweeping gas flow rate, feed temperature, feed concentration and feed flow rate on the permeate flux. For this purpose, the Taguchi method and design of experiment techniques were harnessed to statistically determine optimum operational conditions. Besides that, a comprehensive surface and permeation characterization was conducted against the hand-made membranes. Results showcased that the membrane performance was ultimately controlled by the feed temperature and was nearly (~680) % higher when the temperature raised from 45 to 65 °C. Also, to a lesser extent, the system was dominated by the feed flow rate. As the adopted feed flow rate increases (from 0.2 to 0.6 L/min), around 47.5% increment was bestowed on water permeability characteristics. In contra, 34.5% flux decline was witnessed when higher saline feed concentration (100 g/L) was utilized. In the meantime, with raising the sweeping gas flow rate (from 120 to 300 L/h), the distillate was nearly 129% higher. Based on Taguchi design, the maximum permeate flux (17.3 and 17 kg/m2·h) was secured at 35 g/L, 0.4 L/min, 65 °C and 300 L/h, for both commercial and prepared membranes, respectively.

scholarly journals Employing full factorial design and response surface methodology for optimizing direct contact membrane distillation operational conditions in desalinating the rejected stream of a reverse osmosis unit at Esfahan refinery–Iran

2018 ◽  
Vol 19 (2) ◽  
pp. 492-501 ◽  
Author(s):  
M. Ebadi ◽  
M. R. Mozdianfard ◽  
M. Aliabadi
Keyword(s):  
Response Surface Methodology ◽  
Reverse Osmosis ◽  
Flow Rate ◽  
Direct Contact ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
Operational Conditions ◽  
Direct Contact Membrane Distillation ◽  
Full Factorial ◽  
Feed Temperature

Abstract Optimized condition for desalination of the reverse osmosis (RO) rejected stream from Esfahan Oil Refining Company (EORC) using direct contact membrane distillation (DCMD) with polytetrafluoroethylene (PTFE) membrane was investigated here, having designed a set of 34 experiments using response surface methodology (RSM) and full factorial design (FFD) modelling, carried out in a laboratory scale set-up built for this purpose. Statistical criteria for validation, significance, accuracy and adequacy confirmed the suitability of the quadratic polynomial model employed. Response plots and regression equations suggested that the permeate flux response improved with increased feed temperature, reduced permeate temperature and enhanced feed flow rate. Optimizing DCMD process showed that maximum permeate flux of 60.76 L/m2·h could be achieved at the following optimum operational conditions: feed temperature and flow rate of 70 °C and 2 L/min, respectively, as well as the permeate temperature of 15 °C. At this point, the mean annual energy required for 90% water recovery (36 m3/h off the RO brackish rejected stream) at EORC refinery was found to be 96 GJ, which could be supplied using solar or conventional energy systems at Isfahan, facing a very critical water shortage at present.

Water Desalination Using Direct Contact Membrane Distillation System

2015 ◽  
Author(s):  
Hafiz M. Ahmad ◽  
Atia E. Khalifa ◽  
Mohamed A. Antar
Keyword(s):  
Flow Rate ◽  
Direct Contact ◽  
Membrane Distillation ◽  
Operating Conditions ◽  
Water Desalination ◽  
Feed Flow Rate ◽  
Direct Contact Membrane Distillation ◽  
Rejection Factor ◽  
System Output ◽  
Feed Temperature

Membrane distillation (MD) is a separation technique used for water desalination, which operates at low feed temperatures and pressures. Direct contact membrane distillation (DCMD) is one of the common MD configurations where both the hot saline feed stream and the cold permeate stream are in direct contact with the two membrane surfaces. An experimental study was performed to investigate the effect of operating conditions such as feed temperature, feed flow rate, permeate temperature, and permeate flow rate on the system output flux. To check the effect of membrane degradation, the MD system was run continuously for 48 hours with raw seawater as feed and the reduction in system flux with time was observed. Results showed that increasing the feed temperature, decreasing the permeate temperature, increasing the feed and permeate flow rate yield an increase in flux. The effects of feed temperature and feed flow rate are the most significant parameters. After 48 hours of system continuous operation flux was reduced by 42.4 % but the quality of permeate (as measured by its TDS) is still very high with salt rejection factor close to 100 %. For the DCMD system under consideration, the GOR values remain between 0.8 and 1.2, for the tested range of operating temperatures.

Separation of HCl/water mixture using air gap membrane distillation, Taguchi optimization and artificial neural network

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Sarita Kalla ◽  
Rakesh Baghel ◽  
Sushant Upadhyaya ◽  
Kailash Singh
Keyword(s):  
Water Temperature ◽  
Flow Rate ◽  
Cooling Water ◽  
Membrane Distillation ◽  
Air Gap ◽  
Water Mixture ◽  
Feed Flow Rate ◽  
Ann Model ◽  
Cooling Water Temperature ◽  
Feed Temperature

AbstractThe aim of this paper is to analyze the performance of the air gap membrane distillation (AGMD) process for the separation of HCl/Water mixture first by applying Taguchi optimization approach and second by developing an artificial neural network (ANN) model. The experimental data which are fed as input to the above approaches are collected from the fabricated AGMD lab-scale setup using poly-tetra-fluoro-ethylene membrane of 0.22 µm pore size. The process input variables considered are bulk feed temperature, feed flow rate, air gap thickness, cooling water temperature and cooing water flow rate and AGMD performance index is the total permeate flux. The optimum operating condition is found to be at feed temperature 50 °C, air gap thickness 7 mm, cooling water temperature 5 °C and feed flow rate 10 lpm. Analysis of variance test is carried out for both Taguchi and ANN models. Regression model has also been developed for the comparison between experimental and model predicted data. The developed ANN model has been found well fitted with experimental data having R2 value of 0.998. Based on the calculated percentage of contribution of each input parameter on the AGMD permeate flux, it can be concluded that feed temperature and air gap thickness have highest weightage whereas feed flow rate and cooling water temperature have moderate effects. Predictive ability of the developed ANN model is further checked with 2D contour plot. The distinctive feature of the paper is the development of the Taguchi experimental design and ANN model and then consequently integration of both Taguchi and ANN has been carried out to optimized the developed ANN model parameters.

Modeling of Air-Gap Membrane Distillation and Comparative Study with Direct Contact Membrane Distillation

2020 ◽  
Vol 59 (50) ◽  
pp. 21930-21947
Author(s):  
Sadaf Noamani ◽  
Shirin Niroomand ◽  
Masoud Rastgar ◽  
Mehdi Azhdarzadeh ◽  
Mohtada Sadrzadeh
Keyword(s):  
Comparative Study ◽  
Direct Contact ◽  
Membrane Distillation ◽  
Air Gap ◽  
Air Gap Membrane Distillation ◽  
Direct Contact Membrane Distillation
Sign in / Sign up

Export Citation Format

Share Document