scholarly journals Performance Investigation of O-Ring Vacuum Membrane Distillation Module for Water Desalination

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Adnan Alhathal Alanezi ◽  
H. Abdallah ◽  
E. El-Zanati ◽  
Adnan Ahmad ◽  
Adel O. Sharif
Keyword(s):  
Flow Rate ◽  
Membrane Distillation ◽  
Membrane Module ◽  
Water Desalination ◽  
Feed Flow Rate ◽  
Permeate Flux ◽  
Vacuum Degree ◽  
Flat Sheet ◽  
Vacuum Membrane Distillation ◽  
Feed Temperature

A new O-ring flat sheet membrane module design was used to investigate the performance of Vacuum Membrane Distillation (VMD) for water desalination using two commercial polytetrafluoroethylene (PTFE) and polyvinylidene fluoride (PVDF) flat sheet hydrophobic membranes. The design of the membrane module proved its applicability for achieving a high heat transfer coefficient of the order of 103 (W/m2 K) and a high Reynolds number (Re). VMD experiments were conducted to measure the heat and mass transfer coefficients within the membrane module. The effects of the process parameters, such as the feed temperature, feed flow rate, vacuum degree, and feed concentration, on the permeate flux have been investigated. The feed temperature, feed flow rate, and vacuum degree play an important role in enhancing the performance of the VMD process; therefore, optimizing all of these parameters is the best way to achieve a high permeate flux. The PTFE membrane showed better performance than the PVDF membrane in VMD desalination. The obtained water flux is relatively high compared to that reported in the literature, reaching 43.8 and 52.6 (kg/m2 h) for PVDF and PTFE, respectively. The salt rejection of NaCl was higher than 99% for both membranes.

scholarly journals A Comparison Study of Brine Desalination using Direct Contact and Air Gap Membrane Distillation

2019 ◽  
Vol 25 (11) ◽  
pp. 47-54
Author(s):  
Ahmed Shamil Khalaf ◽  
Asrar Abdullah Hassan
Keyword(s):  
Flow Rate ◽  
Direct Contact ◽  
Polyvinylidene Fluoride ◽  
Membrane Distillation ◽  
Air Gap ◽  
Feed Flow Rate ◽  
Permeate Flux ◽  
Air Gap Membrane Distillation ◽  
Flat Sheet ◽  
Feed Temperature

Membrane distillation (MD) is a hopeful desalination technique for brine (salty) water. In this research, Direct Contact Membrane Distillation (DCMD) and  Air Gap Membrane Distillation (AGMD) will be used. The sample used is from Shat Al –Arab water (TDS=2430 mg/l). A polyvinylidene fluoride (PVDF) flat sheet membrane was used as a flat sheet form with a plate and frame cell. Several parameters were studied, such as; operation time, feed temperature, permeate temperature, feed flow rate. The results showed that with time, the flux decreases because of the accumulated fouling and scaling on the membrane surface. Feed temperature and feed flow rate had a positive effect on the permeate flux, while permeate temperature had a reverse effect on permeate flux. It is noticeable that the flux in DCMD is greater than AGMD, at the same conditions. The flux in DCMD is 10.95LMH, and that in AGMD is 7.14 LMH.  In AGMD, the air gap layer made a high resistance. Here the temperature transport reduces in the permeate side of AGMD due to the air gap resistance. The heat needed for AGMD is lower than DCMD, this leads to low permeate flux because the temperature difference between the two sides is very small, so the driving force (vapor pressure) is low.                                                                                               

Treatment of Industrial Wastewater Containing High Levels of Ammonia and Salt Using Vacuum Membrane Distillation

2014 ◽  
Vol 539 ◽  
pp. 805-810 ◽  
Author(s):  
Yi Min Zhang ◽  
Wei Huang ◽  
Shen Xu Bao
Keyword(s):  
Flow Rate ◽  
Industrial Wastewater ◽  
Membrane Distillation ◽  
Ammonia Removal ◽  
Transfer Model ◽  
Feed Flow Rate ◽  
Vacuum Degree ◽  
Theoretical Mass ◽  
Vacuum Membrane Distillation ◽  
Feed Temperature

The wastewater containing extreme high levels of ammonia and salt was treated by vacuum membrane distillation (VMD). The effects of feed flow rate, temperature and vacuum degree on ammonia removal efficiency (ARE) were investigated systematically. The ARE can be promoted by increasing feed flow rate, feed temperature and vacuum degree in this study. The theoretical mass transfer model was obtained based on series of theory derivation, and the theoretical released ammonia is consistent with the experimental data at conditions ranged in this study, indicating that the developed model is suitable to evaluate the ammonia removal during VMD process.

Performance of Air Gap Membrane Distillation Unit for Water Desalination

2014 ◽  
Author(s):  
Atia E. Khalifa ◽  
Dahiru U. Lawal ◽  
Mohamed A. Antar
Keyword(s):  
Flow Rate ◽  
Membrane Distillation ◽  
Air Gap ◽  
Water Desalination ◽  
Feed Water ◽  
Feed Flow Rate ◽  
Permeate Flux ◽  
Air Gap Membrane Distillation ◽  
Gap Width ◽  
Feed Temperature

Due to water scarcity in the Arabic gulf region, water desalination technologies are considered extremely important. The present work represents a fundamental study on the effect of basic operating and design variables on the flux of an air gap membrane distillation (AGMD) unit for water desalination. The flat sheet, channeled air gap membrane distillation module was designed and manufactured locally. The effect of feed flow rate, feed temperature, coolant water temperature, the air gap width, and the water salinity on the module flux are investigated. Analytical model for heat and mass transfer is used to predict the flux and the model results are compared to the experimental ones. Results showed that the technique has good potential to be used for water desalination. The permeate flux is increased by increasing feed flow rate, feed temperature, decreasing the air gap width, decreasing coolant temperature, and decreasing salinity of feed water. For a given feed flow rate, the width of the air gap and the feed water temperature are found to be the most effective parameters in increasing the distillate flux. Predicting the permeate flux with analytical models for heat and mass transfer showed good agreement with experimental results.

scholarly journals A Systematic Framework for Optimizing a Sweeping Gas Membrane Distillation (SGMD)

Membranes ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 254
Author(s):  
Nawras N. Safi ◽  
Salah. S. Ibrahim ◽  
Nasser Zouli ◽  
Hasan Shaker Majdi ◽  
Qusay F. Alsalhy ◽  
...  
Keyword(s):  
Flow Rate ◽  
Gas Flow ◽  
Membrane Distillation ◽  
Feed Flow Rate ◽  
Permeate Flux ◽  
Gas Flow Rate ◽  
Feed Concentration ◽  
Sweeping Gas ◽  
Feed Temperature ◽  
Systematic Framework

The present work has undertaken a meticulous glance on optimizing the performance of an SGMD configuration utilized a porous poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-co-HFP) membrane. This was carried out by conducting a systematic framework for investigating and optimizing the pertinent parameters such as sweeping gas flow rate, feed temperature, feed concentration and feed flow rate on the permeate flux. For this purpose, the Taguchi method and design of experiment techniques were harnessed to statistically determine optimum operational conditions. Besides that, a comprehensive surface and permeation characterization was conducted against the hand-made membranes. Results showcased that the membrane performance was ultimately controlled by the feed temperature and was nearly (~680) % higher when the temperature raised from 45 to 65 °C. Also, to a lesser extent, the system was dominated by the feed flow rate. As the adopted feed flow rate increases (from 0.2 to 0.6 L/min), around 47.5% increment was bestowed on water permeability characteristics. In contra, 34.5% flux decline was witnessed when higher saline feed concentration (100 g/L) was utilized. In the meantime, with raising the sweeping gas flow rate (from 120 to 300 L/h), the distillate was nearly 129% higher. Based on Taguchi design, the maximum permeate flux (17.3 and 17 kg/m2·h) was secured at 35 g/L, 0.4 L/min, 65 °C and 300 L/h, for both commercial and prepared membranes, respectively.

Water Desalination Using Direct Contact Membrane Distillation System

2015 ◽  
Author(s):  
Hafiz M. Ahmad ◽  
Atia E. Khalifa ◽  
Mohamed A. Antar
Keyword(s):  
Flow Rate ◽  
Direct Contact ◽  
Membrane Distillation ◽  
Operating Conditions ◽  
Water Desalination ◽  
Feed Flow Rate ◽  
Direct Contact Membrane Distillation ◽  
Rejection Factor ◽  
System Output ◽  
Feed Temperature

Membrane distillation (MD) is a separation technique used for water desalination, which operates at low feed temperatures and pressures. Direct contact membrane distillation (DCMD) is one of the common MD configurations where both the hot saline feed stream and the cold permeate stream are in direct contact with the two membrane surfaces. An experimental study was performed to investigate the effect of operating conditions such as feed temperature, feed flow rate, permeate temperature, and permeate flow rate on the system output flux. To check the effect of membrane degradation, the MD system was run continuously for 48 hours with raw seawater as feed and the reduction in system flux with time was observed. Results showed that increasing the feed temperature, decreasing the permeate temperature, increasing the feed and permeate flow rate yield an increase in flux. The effects of feed temperature and feed flow rate are the most significant parameters. After 48 hours of system continuous operation flux was reduced by 42.4 % but the quality of permeate (as measured by its TDS) is still very high with salt rejection factor close to 100 %. For the DCMD system under consideration, the GOR values remain between 0.8 and 1.2, for the tested range of operating temperatures.

Removal of high concentration Congo red by hydrophobic PVDF hollow fiber composite membrane coated with a loose and porous ZIF-71PVDF layer through vacuum membrane distillation

2020 ◽  
pp. 152808372096707
Author(s):  
Hongbin Li ◽  
Wenying Shi ◽  
Qiyun Du ◽  
Shoufa Huang ◽  
Haixia Zhang ◽  
...  
Keyword(s):  
Flow Rate ◽  
Hollow Fiber ◽  
Congo Red ◽  
Fiber Composite ◽  
Water Flux ◽  
Membrane Distillation ◽  
Feed Flow Rate ◽  
High Concentration ◽  
Operation Conditions ◽  
Feed Temperature

Although membrane distillation (MD) technology has the outstanding advantages of almost 100% solute retention and mild operation conditions, its further development is limited by low permeate flux. In order to solve the problem, the improvement of membrane hydrophobicity becomes one of the effective solutions. In this study, a loose and porous hydrophobic zeolitic imidazolate frameworks-71 (ZIF-71)/polyvinylidene fluoride (PVDF) coating layer was composited on the outside surface of PVDF hollow fiber support membrane by the dilute solution coating to enhance membrane hydrophobicity. The prepared hollow fiber composite (HFC) membranes were employed to remove high concentration Congo red (CR) through VMD. The effects of different operation conditions including the dye concentration, feed temperature, vacuum pressure and feed flow rate on CR rejection and permeate water flux were investigated. In the variation range of operating conditions, all the CR rejection of the PVDF HFC membranes shows a slight change and remains above 99.9%. Under the optimal operation conditions including dye concentration 600 mg·L−1, vacuum pressure 31.325 kPa, feed temperature 60°C and feed flow rate 50 L·h−1, HFC membrane exhibit a permeate water flux of 13.15 kg·m−2·h−1. HFC membrane suffers dye fouling during the continuous dye filtration for 100 h. The fouling mechanism was proposed and a combined cleaning way including forward washing, back flushing and chemical desorption has been proved to be effective in recovering membrane water flux.

Experimental study of multi-effect membrane distillation (MEMD) for treatment of water containing inorganic salts

2016 ◽  
Vol 11 (4) ◽  
pp. 765-773 ◽  
Author(s):  
Bhausaheb L. Pangarkar ◽  
Samir K. Deshmukh ◽  
Prashant V. Thorat
Keyword(s):  
Flow Rate ◽  
Separation Efficiency ◽  
Operating Time ◽  
Specific Energy Consumption ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
Carbonate Solutions ◽  
Inorganic Solutes ◽  
Latent Heat Of Vaporization ◽  
Feed Temperature

A novel multi-effect membrane distillation (MEMD) process has been implemented to treat water containing four different inorganic solutes. The 4-stage MEMD module was developed based on the air-gap configuration. The influence of operating parameters like concentration, feed temperature, flow rate and operating time on permeate fluxes of zinc sulfate, sodium fluoride, magnesium chloride and sodium carbonate solutions was observed. Concentration had negligible effect on the MEMD's permeate flux, while its performance increased with increasing feed temperature and flow rate. Its separation efficiency was stable at more than99.91% throughout the experiment. In addition, its specific energy consumption after the recovery of the latent heat of vaporization and sensible heat of brine was measured at different component concentrations and found to be independent of the type of component.

Taguchi Method in the Evaluation of Vacuum Membrane Distillation in Water Desalination

2013 ◽  
Vol 781-784 ◽  
pp. 2366-2369
Author(s):  
Salman Masoudi Soltani ◽  
Sara Kazemi Yazdi
Keyword(s):  
Taguchi Method ◽  
Flow Rate ◽  
Salt Concentration ◽  
Membrane Fouling ◽  
Water Flow Rate ◽  
Membrane Distillation ◽  
Water Desalination ◽  
Operational Parameters ◽  
Vacuum Membrane Distillation ◽  
Membrane Contact

Taguchi method has been applied to evaluate the effects of operational parameters on the efficiency of vacuum membrane distillation (VMD) in the desalination of water. It was observed that permeate increases with an increase in feed temperature and vacuum pressure. However, feed salt concentration adversely affected the amount of the collected permeate due to the reduction of vapour pressure as a result of the presence of the solute in water. Flow rate, however, could only increase the permeate if it was increased from 37.5 to 50 ml/s. Any further increase in flow rate to 100 ml/s, negatively lowered the permeate due to the limited feed/membrane contact time. We observed that at very high salt concentration (300 g/l) the permeate reduces accordingly, highlighting the fact that VMD should be used with care due to the presence of membrane fouling and/or other simultaneous flux-lowering effects present at concentrated feeds.

Sign in / Sign up

Export Citation Format

Share Document