scholarly journals THE INFLUENCE OF HIGH-TEMPERATURE CAREER IN INITIAL-STAGES ON STRENGTH DEVELOPMENT OF HIGH-STRENGTH CONCRETE USING LOW-HEAT PORTLAND CEMENT AND SILICA FUME

2006 ◽  
Vol 71 (601) ◽  
pp. 15-21 ◽  
Author(s):  
Hiroshi KAWAKAMI ◽  
Yoshikatsu NISHIMOTO ◽  
Yoshihiro MASUDA
Keyword(s):  
High Temperature ◽  
Portland Cement ◽  
Silica Fume ◽  
High Strength Concrete ◽  
High Strength ◽  
Strength Development ◽  
Strength Concrete

scholarly journals Influence of Different Drying Conditions on High Strength Concrete Compressive Strength

10.14311/228 ◽  
2001 ◽  
Vol 41 (3) ◽  
Author(s):  
M. Safan ◽  
A. Kohoutková
Keyword(s):  
Compressive Strength ◽  
Silica Fume ◽  
High Strength Concrete ◽  
High Strength ◽  
Strength Development ◽  
Concrete Compressive Strength ◽  
Strength Concrete ◽  
Development Rates ◽  
Drying Conditions

The influence of different drying conditions on the compressive strength and strength development rates of high strength concrete up to an age of 28 days was evaluated. Two HSC mixes with and without silica fume addition were used to cast cubes of 10 cm size. The cubes were stored in different drying conditions until the age of testing at 3, 7, 28 days.

Study on Strength Development of High Strength Concrete Containing Alccofine and Fly-Ash

2012 ◽  
Vol 2 (3) ◽  
pp. 102-104 ◽  
Author(s):  
Suthar Sunil B ◽  
◽  
Dr. (Smt.) B. K. Shah Dr. (Smt.) B. K. Shah
Keyword(s):  
Fly Ash ◽  
High Strength Concrete ◽  
High Strength ◽  
Strength Development ◽  
Strength Concrete

Effects of Two Polypropylene Fibers on the Properties of High Strength Concrete

2013 ◽  
Vol 357-360 ◽  
pp. 1328-1331
Author(s):  
Bai Rui Zhou ◽  
Dong Dong Han ◽  
Jian Hua Yang ◽  
Yi Liang Peng ◽  
Guo Xin Li
Keyword(s):  
Portland Cement ◽  
Modulus Of Elasticity ◽  
High Strength Concrete ◽  
Polypropylene Fiber ◽  
High Strength ◽  
Polypropylene Fibers ◽  
Strength Concrete ◽  
Reticular Fiber ◽  
Binder Ratio ◽  
Water To Binder Ratio

Portland cement, crushed stone, sand and superplasticizer were used to obtain a high strength concrete with a low water to binder ratio. A reticular polypropylene fiber and a single polypropylene fiber were used to improve the strength of the high strength concrete, but the effects of the two fibers on the slump and strengths were quite different. The reasons of the differences were the surface area and the modulus of elasticity of the fibers. The results show the reticular fiber was better to used in high strength concretes.

Comparison Analysis on the Mechanical Properties of HSC and NSC after the Action of High Temperatures

2014 ◽  
Vol 1014 ◽  
pp. 49-52
Author(s):  
Xiao Ping Su
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
High Temperatures ◽  
High Strength Concrete ◽  
Elasticity Modulus ◽  
Strain Curve ◽  
Peak Stress ◽  
High Strength ◽  
Peak Strain ◽  
Strength Concrete

With the wide application of high strength concrete in the building construction,the risk making concrete subject to high temperatures during a fire is increasing. Comparison tests on the mechanical properties of high strength concrete (HSC) and normal strength concrete (NSC) after the action of high temperature were made in this article, which were compared from the following aspects: the peak stress, the peak strain, elasticity modulus, and stress-strain curve after high temperature. Results show that the laws of the mechanical properties of HSC and NSC changing with the temperature are the same. With the increase of heating temperature, the peak stress and elasticity modulus decreases, while the peak strain grows rapidly. HSC shows greater brittleness and worse fire-resistant performance than NSC, and destroys suddenly. The research and evaluation on the fire-resistant performance of HSC should be strengthened during the structural design and construction on the HSC buildings.

Sign in / Sign up

Export Citation Format

Share Document