scholarly journals DEVELOPMENT OF PARALLEL CHORD TRUSS USING PRE-CUT SYSTEM AND STANDARD SIZE TIMBER FOR RESIDENTIAL USE

2017 ◽  
Vol 23 (54) ◽  
pp. 487-492
Author(s):  
Kenta SASAKI ◽  
Hirohide TAO ◽  
Hiro KAWAHARA ◽  
Kenji AOKI ◽  
Masahiro INAYAMA ◽  
...  
Author(s):  
Edward G. Bartick ◽  
John A. Reffner

Since the introduction of commercial Fourier transform infrared (FTIR) microscopic systems in 1983, IR microscopy has developed as an important analytical tool in research, industry and forensic analysis. Because of the frequent encounter of small quantities of physical evidence found at crime scenes, spectroscopic IR microscopes have proven particularly valuable for forensic applications. Transmittance and reflectance measurements have proven very useful. Reflection-absorption, specular reflection, and diffuse reflection have all been applied. However, it has been only very recently that an internal reflection (IRS) objective has been commercially introduced.The IRS method, also known as attenuated total reflection (ATR), has proven very useful for IR analysis of standard size samples. The method has been applied to adhesive tapes, plastic explosives, and general applications in the analysis of opaque materials found as evidence. The small quantities or uncontaminated areas of specimens frequently found requiring forensic analysis will often be directly applicable to microscopic IRS analysis.


1987 ◽  
Author(s):  
Billy Dees ◽  
John A. Centrone ◽  
Jim Sartain

2002 ◽  
Vol 67 (11) ◽  
pp. 1596-1608 ◽  
Author(s):  
Josef Janča

The effect of miniaturization of the separation channel on the performance of thermal field-flow fractionation (TFFF) is substantiated theoretically. The experiments carried out under carefully chosen experimental conditions proved the high performance of the separation of polymers within an extended range of molar masses from relatively low up to ultrahigh-molar-mass (UHMM) samples. The new micro-TFFF allows to achieve high resolution when applying constant field force operation, it makes easy the programming of the temperature drop which is an advantageous operational mode from the point of view of the time of analysis, and it extends considerably the range of perfectly controlled temperature of the cold wall due to a substantial decrease in the heat energy flux compared with standard size channels.


Author(s):  
Karen J. Esler ◽  
Anna L. Jacobsen ◽  
R. Brandon Pratt

Extensive habitat loss and habitat conversion has occurred across all mediterranean-type climate (MTC) regions, driven by increasing human populations who have converted large tracts of land to production, transport, and residential use (land-use, land-cover change) while simultaneously introducing novel forms of disturbance to natural landscapes. Remaining habitat, often fragmented and in isolated or remote (mountainous) areas, is threatened and degraded by altered fire regimes, introduction of invasive species, nutrient enrichment, and climate change. The types and impacts of these threats vary across MTC regions, but overall these drivers of change show little signs of abatement and many have the potential to interact with MTC region natural systems in complex ways.


1947 ◽  
Vol 20 (2) ◽  
pp. 525-526
Author(s):  
W. H. Willott

Abstract In a series of cross-breaking tests carried out on hard rubber during hot weather, the values of the breaking elongation were higher than was expected, although the cross-breaking strength was of the usual order. It was thought that the high temperature might account for these results by making the hard rubber more plastic. The following experiments were, therefore, performed to investigate the effect of small changes of temperature, such as are encountered at different times of the year, on the cross-breaking strength and elongation. Test-pieces of standard size (75 × 25 × 5 mm.) were cut from a sheet of hard rubber of the composition: 68 per cent rubber, 32 per cent sulfur, which had been vulcanized for 5 hours at 155° C. They were immersed in a beaker of water and kept at the required temperature for about 15 minutes, when they were judged to have attained a steady temperature. The tests were carried out on an Avery fabric-testing machine fitted with special clamps to give a three-point loading test, the distance between the supporting knife-edges being 50.4 mm. (2 in.). These clamps were heated to the temperature of the specimens by means of an electric radiator. The specimens were tested as soon as possible after they had been removed from the water, so that the change of temperature during the test was reduced as far as possible. The standard conditions already laid down, were observed.


Author(s):  
Sotirios D. Kotsopoulos ◽  
Federico Casalegno ◽  
Leonardo Giusti ◽  
Wesley Graybill
Keyword(s):  

2010 ◽  
Vol 33 (11) ◽  
pp. 1186-1191 ◽  
Author(s):  
Elisa Bonso ◽  
Francesca Saladini ◽  
Ada Zanier ◽  
Elisabetta Benetti ◽  
Francesca Dorigatti ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document