Using Multi-Objective Evolutionary Algorithms to Optimize Mechanical Properties of Injection Molded Parts

2005 ◽  
Vol 20 (3) ◽  
pp. 274-285 ◽  
Author(s):  
A. Gaspar-Cunha ◽  
J. C. Viana
Keyword(s):  
Mechanical Properties ◽  
Evolutionary Algorithms ◽  
Multi Objective ◽  
Molded Parts ◽  
Injection Molded

Deposition-induced effects of isotactic polypropylene and polycarbonate composites during fused deposition modeling

2017 ◽  
Vol 23 (5) ◽  
pp. 869-880 ◽  
Author(s):  
Ying-Guo Zhou ◽  
Bei Su ◽  
Lih-sheng Turng
Keyword(s):  
Mechanical Properties ◽  
Design Methodology ◽  
Fused Deposition Modeling ◽  
Content Type ◽  
Fused Deposition ◽  
Close Relationship ◽  
Molded Parts ◽  
Deposition Modeling ◽  
Injection Molded ◽  
First Time

Purpose Although the feasibility and effectiveness of the fused deposition modeling (FDM) method have been proposed and developed, studies of applying this technology to various materials are still needed for researching its applicability, especially with regard to polymer blends and composites. The purpose of this paper is to study the deposition-induced effect and the effect of compatibilizers on the mechanical properties of polypropylene and polycarbonate (PP/PC) composites. Design/methodology/approach For this purpose, three different deposition modes for PP/PC composites with or without compatibilizers were used for the FDM method and tested for tensile properties. Also, parts with the same materials were made by injection molding and used for comparison. In addition, different deposition speeds were used to investigate the different deposition-induced effects. Furthermore, the behavior of the mechanical properties was clarified with scanning electron microscope images of the fracture surfaces. Findings The research results suggest that the deposition orientation has a significant influence on the mechanical behavior of PP/PC composite FDM parts. The results also indicate that there is a close relationship between the mechanical properties and morphological structures which are deeply influenced by compatibilization. Compared with injection molded parts, the ductility of the FDM parts can be dramatically improved due to the formation of fibrils and micro-fibrils by the deposition induced during processing. Originality/value This is the first paper to investigate a PP/PC composite FDM process. The results of this paper verified the applicability of PP/PC composites to FDM technology. It is also the first time that the deposition-induced effect during FDM has been investigated and studied.

scholarly journals Polymer Composites Used in Rapid Prototyping Technology

2020 ◽  
Vol 44 (1) ◽  
pp. 15-20
Author(s):  
Katarzyna Bulanda ◽  
Mariusz Oleksy ◽  
Rafał Oliwa ◽  
Grzegorz Budzik ◽  
Tadeusz Markowski
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
New Materials ◽  
Fused Deposition ◽  
The Matrix ◽  
Molded Parts ◽  
Deposition Modeling ◽  
Injection Molded ◽  
The Impact

AbstractNew materials and filaments dedicated to 3D printing were obtained using the fused deposition modeling method, and the properties of the produced materials were investigated. Polylactide was used as a polymer base for the assays because of the desired properties of the polymer, mainly biodegradability, and the matrix was refilled by the addition of metallic nanofillers, such as bronze, copper, brass, and steel. For the composites obtained, mechanical properties were investigated to determine the dependence of the obtained results on the content and type of filler used and on the method of fabrication of the fittings. It was found that the additives present in the polymer matrix increased the fluidity of the material. The best results were obtained for the compositions with bronze and steel in which the mass flow rate was 72.97 and 79.99 g/10 min, respectively. The filled material that had lower hardness was measured by Rockwell and the impact strength was measured by Charpy. In addition, it was found that injection-molded parts obtained much better mechanical properties than those obtained by 3D printing.

Effect of the impact conditions on the mechanical properties of injection-molded parts

2012 ◽  
Vol 52 (9) ◽  
pp. 1845-1853 ◽  
Author(s):  
Carlos N. Barbosa ◽  
Júlio C. Viana ◽  
Markus Franzen ◽  
Ricardo Simoes
Keyword(s):  
Mechanical Properties ◽  
Molded Parts ◽  
Injection Molded ◽  
The Impact

Interfacial Effects on the Mechanical Properties of GF/PP Injection Molded Composites

1998 ◽  
Vol 7 (1) ◽  
pp. 096369359800700 ◽  
Author(s):  
A. Eggert ◽  
R. Walter ◽  
H. Hamada ◽  
K. Friedrich
Keyword(s):  
Mechanical Properties ◽  
Fatigue Behavior ◽  
Interfacial Strength ◽  
Extrusion Process ◽  
Surface Treatments ◽  
Basic Material ◽  
Interfacial Effects ◽  
Molded Parts ◽  
Injection Molded ◽  
Short Glass

The mechanical properties of short glass fiber (GF) reinforced Polypropylene (PP) injection molded parts with various surface treatments and different compounding methods were investigated in this study. The effects of the different surface treatments on the interfacial strength as well as the influence of the pre-molding compounding process and its parameters on the composites' characteristics were determined. Next to basic material properties a focus was laid on fracture toughness and fatigue behavior. A clear recommendation as to kind of the extrusion process could be established and the interfacial effects on the overall mechanical properties of the tested materials could be assessed.

An Experimental Investigation of a Micro Injection Molded Mechanical Device

2005 ◽  
Author(s):  
Alan M. Tom ◽  
Aleksandar K. Angelov ◽  
John P. Coulter
Keyword(s):  
Mechanical Properties ◽  
Experimental Investigation ◽  
Injection Molding ◽  
Processing Parameters ◽  
Primary Objective ◽  
Crystalline Materials ◽  
Reduced Modulus ◽  
Molded Parts ◽  
Secondary Objective ◽  
Injection Molded

The primary objective of this study, through a scientific experimental investigation, was to determine optimum injection molding processing parameters on semi-crystalline materials HDPE and POM focusing on mechanical properties, obtained thru the use of a nano-indenter, of micro gears being manufactured on non-heated and heated mold bases. A secondary objective was to initiate a similar experimental study using amorphous COC material. Taguchi’s method utilizing an L-9 orthogonal array was used to determine the effects of Tnoz, Tmold, Pinj, Vinj, Ppack, and tpack injection molding processing parameters. A nano-indenter was used to determine investigated mechanical properties on final injection molded parts that included stiffness (S), reduced modulus (Er), and hardness (H). Results showed HDPE, POM and COC, heated mold experiments exhibiting increases in mechanical properties S, Er, and H, on the order of 1.2–4.0 times those of non-heated molding trials. Decreases in optimum molding conditions for Tnoz, Pinj, and Ppack was also observed for heated molding trials. The highest mold temperatures and injection pressures tested did not produce greatest optimum molding conditions. However, largest packing times tested produced optimum molding conditions.

Sign in / Sign up

Export Citation Format

Share Document