Fluorocarbon Precursor for High Aspect Ratio via Milling in Focused Ion Beam Modification of Integrated Circuits

Author(s):  
Valery Ray

Abstract Gas Assisted Etching (GAE) is the enabling technology for High Aspect Ratio (HAR) circuit access via milling in Focused Ion Beam (FIB) circuit modification. Metal interconnect layers of microelectronic Integrated Circuits (ICs) are separated by Inter-Layer Dielectric (ILD) materials, therefore HAR vias are typically milled in dielectrics. Most of the etching precursor gases presently available for GAE of dielectrics on commercial FIB systems, such as XeF2, Cl2, etc., are also effective etch enhancers for either Si, or/and some of the metals used in ICs. Therefore use of these precursors for via milling in dielectrics may lead to unwanted side effects, especially in a backside circuit edit approach. Making contacts to the polysilicon lines with traditional GAE precursors could also be difficult, if not impossible. Some of these precursors have a tendency to produce isotropic vias, especially in Si. It has been proposed in the past to use fluorocarbon gases as precursors for the FIB milling of dielectrics. Preliminary experimental evaluation of Trifluoroacetic (Perfluoroacetic) Acid (TFA, CF3COOH) as a possible etching precursor for the HAR via milling in the application to FIB modification of ICs demonstrated that highly enhanced anisotropic milling of SiO2 in HAR vias is possible. A via with 9:1 aspect ratio was milled with accurate endpoint on Si and without apparent damage to the underlying Si substrate.

Author(s):  
Valery Ray

Abstract Precision detection of endpoint after the milling has reached targeted conductor during circuit modification by focused ion beam system is important. While the sensitivity of the endpoint detection can be enhanced by improved secondary electron collection and sample absorbed current monitoring, a detailed understanding of the endpoint signal distribution within a high aspect ratio (HAR) via is of great interest. This article presents an alternative model of HAR via milling endpointing mechanism in which a phenomenon of spatial distribution of the endpoint information within the HAR via is explained based on sputtering of the material from the targeted metal line and redeposition of the spattered material on the via sidewalls. Increased emission of the secondary electrons, resulting from the subsequent bombardment of this conductive re-deposition by the primary ion beam, is detected as the endpoint. A methodology for the future experimental verification of the proposed model is also described.


1994 ◽  
Vol 337 ◽  
Author(s):  
Marsha Abramo ◽  
Loren Hahn

ABSTRACTFocused ion beam (FIB) technology is used to modify circuits for early-product design debug; it also has the capability to create probe points to underlying metallurgy, allowing device characterization while maintaining full functionality. These techniques provide critical feedback to designers for rapid verification of proposed design changes.Current FIB technology has its limitations because of redeposition of sputtered material; this phenomena may induce vertical electrical shorts and limit the achievable aspect ratio of a milled via to 6:1. Therefore, innovative enhancements are required to provide modification capability on planar chip technology which may utilize up to five levels of metallurgy. The ability to achieve high-aspect-ratio milling is required to access underlying circuitry. Vias with aspect ratios of 10:1 are necessary in some cases.This paper reviews a gas-assisted etching (GAE) process that enhances FIB milling by volatilizing the sputtered material, examines the results obtained from utilizing the GAE process for high-aspect-ratio milling, and discusses selectivity of semiconductor materials (silicon, aluminum, tungsten and silicon dioxide).


Author(s):  
A. Olbrich ◽  
B. Ebersberger ◽  
C. Boit ◽  
Ph. Niedermann ◽  
W. Hänni ◽  
...  

1996 ◽  
Vol 439 ◽  
Author(s):  
Miyoko Tanaka ◽  
Kazuo Furuya ◽  
Tetsuya Saito

AbstractFocused ion beam (FIB) irradiation of a thin Ni2Si layer deposited on a Si substrate was carried out and studied using an in-situ transmission electron microscope (in-situ TEM). Square areas on sides of 4 by 4 and 9 by 9 μm were patterned at room temperature with a 25keV Ga+-FIB attached to the TEM. The structural changes of the films indicate a uniform milling; sputtering of the Ni2Si layer and the damage introducing to the Si substrate. Annealing at 673 K results in the change of the Ni2Si layer into an epitaxial NiSi2 layer outside the FIB irradiated area, but several precipitates appear around the treated area. Precipitates was analyzed by energy dispersive X-ray spectroscopy (EDS). Larger amount of Ni than the surrounding matrix was found in precipitates. Selected area diffraction (SAD) patterns of the precipitates and the corresponding dark field images imply the formation of a Ni rich silicide. The relation between the FIB tail and the precipitation is indicated.


2010 ◽  
Vol 10 (1) ◽  
pp. 497-501 ◽  
Author(s):  
David Caballero ◽  
Guillermo Villanueva ◽  
Jose Antonio Plaza ◽  
Christopher A. Mills ◽  
Josep Samitier ◽  
...  

1998 ◽  
Vol 4 (S2) ◽  
pp. 652-653 ◽  
Author(s):  
A. N. Campbell ◽  
J. M. Soden

A great deal can be learned about integrated circuits (ICs) and microelectronic structures simply by imaging them in a focused ion beam (FIB) system. FIB systems have evolved during the past decade from something of a curiosity to absolutely essential tools for microelectronics design verification and failure analysis. FIB system capabilities include localized material removal, localized deposition of conductors and insulators, and imaging. A major commercial driver for FIB systems is their usefulness in the design debugging cycle by (1) rewiring ICs quickly to test design changes and (2) making connection to deep conductors to facilitate electrical probing of complex ICs. FIB milling is also used for making precision cross sections and for TEM sample preparation of microelectronic structures for failure analysis and yield enhancement applications.


Sign in / Sign up

Export Citation Format

Share Document