Can Illuminated IV-Characteristics of Micro-Regions in Solar Cells be Measured by Laser-Induced Stimulation?

2011 ◽  
Author(s):  
M. Boostandoost ◽  
A. Glowacki ◽  
O. Bakaeva ◽  
U. Kerst ◽  
C. Boit
Keyword(s):  
Solar Cells ◽  
Grain Boundary ◽  
Light Trapping ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Laser Wavelength ◽  
Open Circuit ◽  
Infrared Light ◽  
Boundary States ◽  
Entire Cell

Abstract In this paper, IR-LBIC (Infrared Light Beam Induced Current) is applied using the laser wavelength of 1064 nm in order to analyze polycrystalline thin-film solar cells. The spatially high-resolved map of the short circuit current (~3 µm) has been obtained by performing the IR-LBIC measurement. The results of the measurement showed higher signal response from the grain boundary compared to that from the grain interior. This difference has been explained by the light trapping effect due to the trench-shaped grain boundary profile, which is possibly accompanied by two stage excitation effects via electronic grain boundary states. It has been additionally investigated, whether LBIC measurement could be used to extract local illuminated cell characteristics. However, since the dark current, which has a decisive influence on the solar cell characteristic, is flowing in the entire cell area, this is not possible. A circuit network simulation demonstrates that LBIC cannot be used for extraction of the local open circuit voltage, and the short circuit current is the only parameter that can be locally defined and therefore clearly observed.

scholarly journals Enhanced Performance of Nanotextured Silicon Solar Cells with Excellent Light-Trapping Properties

Photonics ◽  
2021 ◽  
Vol 8 (7) ◽  
pp. 272
Author(s):  
Bingfei Dou ◽  
Rui Jia ◽  
Zhao Xing ◽  
Xiaojiang Yao ◽  
Dongping Xiao ◽  
...  
Keyword(s):  
Solar Cells ◽  
Light Trapping ◽  
Short Circuit ◽  
Surface Recombination ◽  
Atomic Layer ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Surface Recombination Velocity ◽  
Electrode Contact ◽  
Recombination Velocity

Light-trapping nanostructures have been widely used for improving solar cells’ performance, but the higher surface recombination and poor electrode contact introduced need to be addressed. In this work, silicon nanostructures were synthesized via silver-catalyzed etching to texturize solar cells. Atomic-layer-deposited Al2O3 passivated the nanotextured cells. A surface recombination velocity of 126 cm/s was obtained, much lower than the 228 cm/s of the SiNX-passivated one. Additionally, the open-circuit voltage (VOC) of the nanotextured cells improved significantly from 582 to 610 mV, as did the short-circuit current (JSC) from 25.5 to 31 mA/cm2. Furthermore, the electrode contact property was enhanced by light-induced plating. A best efficiency of 13.3% for nano-textured cells was obtained, which is higher than the planar cell’s 12%.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals GaInP/GaAs/poly-Si Multi-Junction Solar Cells by in Metal Balls Bonding

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 726
Author(s):  
Ray-Hua Horng ◽  
Yu-Cheng Kao ◽  
Apoorva Sood ◽  
Po-Liang Liu ◽  
Wei-Cheng Wang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Low Temperature ◽  
Triple Junction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Metal Line ◽  
Solar Simulator ◽  
Junction Solar Cell

In this study, a mechanical stacking technique has been used to bond together the GaInP/GaAs and poly-silicon (Si) solar wafers. A GaInP/GaAs/poly-Si triple-junction solar cell has mechanically stacked using a low-temperature bonding process which involves micro metal In balls on a metal line using a high-optical-transmission spin-coated glue material. Current–voltage measurements of the GaInP/GaAs/poly-Si triple-junction solar cells have carried out at room temperature both in the dark and under 1 sun with 100 mW/cm2 power density using a solar simulator. The GaInP/GaAs/poly-Si triple-junction solar cell has reached an efficiency of 24.5% with an open-circuit voltage of 2.68 V, a short-circuit current density of 12.39 mA/cm2, and a fill-factor of 73.8%. This study demonstrates a great potential for the low-temperature micro-metal-ball mechanical stacking technique to achieve high conversion efficiency for solar cells with three or more junctions.

scholarly journals Ultrathin Cu(In,Ga)Se2 Solar Cells with Ag/AlOx Passivating Back Reflector

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4268
Author(s):  
Jessica de Wild ◽  
Gizem Birant ◽  
Guy Brammertz ◽  
Marc Meuris ◽  
Jef Poortmans ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Solar Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Electron Microscopic ◽  
Current Increase ◽  
Time Resolved ◽  
Cigs Solar Cells

Ultrathin Cu(In,Ga)Se2 (CIGS) absorber layers of 550 nm were grown on Ag/AlOx stacks. The addition of the stack resulted in solar cells with improved fill factor, open circuit voltage and short circuit current density. The efficiency was increased from 7% to almost 12%. Photoluminescence (PL) and time resolved PL were improved, which was attributed to the passivating properties of AlOx. A current increase of almost 2 mA/cm2 was measured, due to increased light scattering and surface roughness. With time of flight—secondary ion mass spectroscopy, the elemental profiles were measured. It was found that the Ag is incorporated through the whole CIGS layer. Secondary electron microscopic images of the Mo back revealed residuals of the Ag/AlOx stack, which was confirmed by energy dispersive X-ray spectroscopy measurements. It is assumed to induce the increased surface roughness and scattering properties. At the front, large stains are visible for the cells with the Ag/AlOx back contact. An ammonia sulfide etching step was therefore applied on the bare absorber improving the efficiency further to 11.7%. It shows the potential of utilizing an Ag/AlOx stack at the back to improve both electrical and optical properties of ultrathin CIGS solar cells.

scholarly journals Direct AFM-based nanoscale mapping and tomography of open-circuit voltages for photovoltaics

2018 ◽  
Vol 9 ◽  
pp. 1802-1808 ◽  
Author(s):  
Katherine Atamanuk ◽  
Justin Luria ◽  
Bryan D Huey
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Three Dimensional ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
Order Of Magnitude ◽  
Individual Grains

The nanoscale optoelectronic properties of materials can be especially important for polycrystalline photovoltaics including many sensor and solar cell designs. For thin film solar cells such as CdTe, the open-circuit voltage and short-circuit current are especially critical performance indicators, often varying between and even within individual grains. A new method for directly mapping the open-circuit voltage leverages photo-conducting AFM, along with an additional proportional-integral-derivative feedback loop configured to maintain open-circuit conditions while scanning. Alternating with short-circuit current mapping efficiently provides complementary insight into the highly microstructurally sensitive local and ensemble photovoltaic performance. Furthermore, direct open-circuit voltage mapping is compatible with tomographic AFM, which additionally leverages gradual nanoscale milling by the AFM probe essentially for serial sectioning. The two-dimensional and three-dimensional results for CdTe solar cells during in situ illumination reveal local to mesoscale contributions to PV performance based on the order of magnitude variations in photovoltaic properties with distinct grains, at grain boundaries, and for sub-granular planar defects.

scholarly journals Effects of Different Doping Ratio of Cu Doped CdS on QDSCs Performance

2015 ◽  
Vol 2015 ◽  
pp. 1-4
Author(s):  
Xiaojun Zhu ◽  
Xiaoping Zou ◽  
Hongquan Zhou
Keyword(s):  
Solar Cells ◽  
Quantum Dot ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Photoelectric Conversion Efficiency ◽  
Photoelectric Conversion ◽  
Sensitized Solar Cells ◽  
Doping Ratio

We use the successive ionic layer adsorption and reaction (SILAR) method for the preparation of quantum dot sensitized solar cells, to improve the performance of solar cells by doping quantum dots. We tested the UV-Vis absorption spectrum of undoped CdS QDSCs and Cu doped CdS QDSCs with different doping ratios. The doping ratios of copper were 1 : 100, 1 : 500, and 1 : 1000, respectively. The experimental results show that, under the same SILAR cycle number, Cu doped CdS quantum dot sensitized solar cells have higher open circuit voltage, short circuit current density photoelectric conversion efficiency than undoped CdS quantum dots sensitized solar cells. Refinement of Cu doping ratio are 1 : 10, 1 : 100, 1 : 200, 1 : 500, and 1 : 1000. When the proportion of Cu and CdS is 1 : 10, all the parameters of the QDSCs reach the minimum value, and, with the decrease of the proportion, the short circuit current density, open circuit voltage, and the photoelectric conversion efficiency are all increased. When proportion is 1 : 500, all parameters reach the maximum values. While with further reduction of the doping ratio of Cu, the parameters of QDSCs have a decline tendency. The results showed that, in a certain range, the lower the doping ratio of Cu, the better the performance of quantum dot sensitized solar cell.

Study of Photoelectrochemical Solar Cell Using WSe2 Crystal

2013 ◽  
Vol 665 ◽  
pp. 330-335 ◽  
Author(s):  
Ripal Parmar ◽  
Dipak Sahay ◽  
R.J. Pathak ◽  
R.K. Shah
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Electrical Energy ◽  
Open Circuit ◽  
Cell Parameters ◽  
Photoelectrochemical Solar Cell ◽  
Photoelectrochemical Solar Cells

The solar cells have been used as most promising device to convert light energy into electrical energy. In this paper authors have attempted to fabricate Photoelectrochemical solar cell with semiconductor electrode using TMDCs. The Photoelectrochemical solar cells are the solar cells which convert the solar energy into electrical energy. The photoelectrochemical cells are clean and inexhaustible sources of energy. The photoelectrochemical solar cells are fabricated using WSe2crystal and electrolyte solution of 0.025M I2, 0.5M NaI, 0.5M Na2SO4. Here the WSe2crystals were grown by direct vapour transport technique. In our investigations the solar cell parameters like short circuit current (Isc) and Open circuit voltage (Voc) were measured and from that Fill factor (F.F.) and photoconversion efficiency (η) are investigated. The results obtained shows that the value of efficiency and fill factor of solar cell varies with the illumination intensities.

Solar Cell Contacts Using Nano-Sized Dispersions

1999 ◽  
Vol 581 ◽  
Author(s):  
Doug Schulz ◽  
R. Ribelin ◽  
X. Wu ◽  
K.M. Jones ◽  
R.J. Matson ◽  
...  
Keyword(s):  
Solar Cells ◽  
Spray Deposition ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Cdte Layer ◽  
Open Circuit ◽  
Alloy Formation ◽  
Current Densities ◽  
P Type ◽  
Open Circuit Voltages

ABSTRACTNano-sized dispersions have been employed as precursor inks for the spray deposition of contacts to both Si and CdTe materials. In the case of Si, nano-sized Al particles (nano-Al) were dispersed and spray deposited onto p-type Si. Annealing above the eutectic temperature causes alloy formation yielding a p+ layer with p ∼ 10−4 Ω•cm. For CdTe, nano-sized Te particles (nano-Te) were dispersed and sprayed onto CdTe/CdS/SnO2/glass heterostructures. Contact to the CdTe layer occurred during a 30 min anneal in He (T = 215 to 255 °C). These solar cells were finished by spin-coating the Te layer with Ag paint and subsequently annealing in air (100 °C / 1 h). This approach produces solar cells with open circuit voltages (Voc) from 720 to 800 mV, short circuit current densities (Jsc) from 18 to 20 mA/cm2 and efficiencies up to 10.3%. The performance of these cells was similar to those produced using the standard NREL contact.

scholarly journals SCAPS Simulation on P3HT:Graphene Nanocomposites Based Bulk-Heterojunction Organic Solar Cells

2019 ◽  
Vol 9 (1) ◽  
pp. 28
Author(s):  
Nur Shakina Mohd Shariff ◽  
Puteri Sarah Mohamad Saad ◽  
Mohamad Rusop Mahmood
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Fill Factor ◽  
Bulk Heterojunction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Simulation Software ◽  
Capacitance Voltage

There has been an increasing interest towards organic solar cells after the discovery of conjugated polymer and bulk-heterojunction concept. Eventhough organic solar cells are less expensive than inorganic solar cells but the power conversion energy is still considered low. The main objective of this research is to investigate the effect of the P3HT’s thickness and concentration towards the efficiency of the P3HT:Graphene solar cells. A simulation software that is specialize for photovoltaic called SCAPS is used in this research to simulate the effect on the solar cells. The solar cell’s structure will be drawn inside the simulation and the parameters for each layers is inserted. The result such as the open circuit voltage (Voc), short circuit current density (Jsc), fill factor (FF), efficiency (η), capacitance-voltage (C-V) and capacitance-frequency (C-f) characteristic will be calculated by the software and all the results will be put into one graph.

scholarly journals Prunus domestica dye extraction for fabrication of zinc oxide based dye-sensitized solar cells

BIBECHANA ◽  
2015 ◽  
Vol 13 ◽  
pp. 23-28
Author(s):  
Leela Pradhan Joshi
Keyword(s):  
Zinc Oxide ◽  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Zinc Nitrate ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Dye Extraction ◽  
Sensitized Solar Cells

Aluminium doped Zinc Oxide (AZO) seed layers were deposited on Fluorine doped Tin Oxide (FTO) substrates using a spin coating technique. These were then immersed in growth solutions of zinc nitrate, hexamethylenetetramine and distilled water to develop nanoplates of Zinc Oxide (ZnO). The nanostructures of ZnO grown on FTO were studied using x-ray diffraction techniques. Dye-sensitized solar cells (DSSC) were fabricated using two prepared electrodes, one of dye-loaded zinc oxide and another that was platinum coated. The electrolyte used was potassium iodide iodine solution. The performance of the assembled DSCCs was tested by drawing an IV curve. The results showed that the short circuit current and open circuit voltages were about 10 microamperes and 270 millivolts respectively.BIBECHANA 13 (2016) 23-28

Sign in / Sign up

Export Citation Format

Share Document