Friction and Wear of Aluminum Alloys and Composites

2017 ◽  
pp. 509-532 ◽  
Keyword(s):  
Aluminum Alloys ◽  
Friction And Wear

712 Improvement of Friction and Wear Properties of Aluminum Alloys by DLC

2013 ◽  
Vol 2013.21 (0) ◽  
pp. 203-204
Author(s):  
Masahumi Nakamura ◽  
Shuto Suzuki ◽  
Sadayuki Kubota
Keyword(s):  
Aluminum Alloys ◽  
Friction And Wear ◽  
Wear Properties ◽  
Friction And Wear Properties

scholarly journals Effects of Doping Elements on the Friction and Wear of SUJ2 Steel Sliding against Aluminum Alloys

Micromachines ◽  
2017 ◽  
Vol 8 (4) ◽  
pp. 96
Author(s):  
Yuh-Ping Chang ◽  
Zi-Wei Huang ◽  
Huann-Ming Chou
Keyword(s):  
Aluminum Alloys ◽  
Friction And Wear

Extrusion Die and Tooling

2000 ◽  
pp. 87-118
Keyword(s):  
Aluminum Alloys ◽  
Friction And Wear ◽  
Thermal Shrinkage ◽  
Basic Design ◽  
Design Considerations ◽  
Extrusion Die ◽  
Die Materials ◽  
And Function

Abstract This chapter familiarizes readers with the design, configuration, and function of tooling and dies used to extrude aluminum alloys. It discuses basic design considerations, including the geometry, location, and orientation of die openings; allowances for thermal shrinkage, stretching, and deflection; and the length and profile of bearing surfaces. It outlines the steps and processes involved in die making, describes the selection and treatment of die materials, and examines the factors that influence friction and wear. It also discusses the general procedures for on-site die correction.

Analytical Electron Microscopy of Ion-Implanted Metals

1985 ◽  
Vol 43 ◽  
pp. 282-285
Author(s):  
D.I. Potter ◽  
M. Ahmed ◽  
K. Ruffing
Keyword(s):  
Electron Microscopy ◽  
Ion Implantation ◽  
Friction And Wear ◽  
Analytical Electron Microscopy ◽  
Chemical Compositions ◽  
Surface Chemical ◽  
Near Surface ◽  
The Past ◽  
Analytical Electron ◽  
Property Changes

Ion implantation, used extensively for the past decade in fabricating semiconductor devices, now provides a unique means for altering the near-surface chemical compositions and microstructures of metals. These alterations often significantly improve physical properties that depend on the surface of the material; for example, catalysis, corrosion, oxidation, hardness, friction and wear. Frequently the mechanisms causing these beneficial alterations and property changes remain obscure and much of the current research in the area of ion implantation metallurgy is aimed at identifying such mechanisms. Investigators thus confront two immediate questions: To what extent is the chemical composition changed by implantation? What is the resulting microstructure? These two questions can be investigated very fruitfully with analytical electron microscopy (AEM), as described below.

Analytical Electron Microscopy Study of Second-Phase Particles in 7075 and 7475 Aluminum Alloys

1985 ◽  
Vol 43 ◽  
pp. 348-349
Author(s):  
M. Raghavan ◽  
J. Y. Koo ◽  
J. W. Steeds ◽  
B. K. Park
Keyword(s):  
Aluminum Alloys ◽  
Silicon Oxide ◽  
Analytical Electron Microscopy ◽  
Microscopy Study ◽  
Electron Microscopy Study ◽  
Partial Substitution ◽  
Second Phase ◽  
X Ray ◽  
Second Phase Particles ◽  
Almost All

X-ray microanalysis and Convergent Beam Electron Diffraction (CBD) studies were conducted to characterize the second phase particles in two commercial aluminum alloys -- 7075 and 7475. The second phase particles studied were large (approximately 2-5μm) constituent phases and relatively fine ( ∼ 0.05-1μn) dispersoid particles, Figures 1A and B. Based on the crystal structure and chemical composition analyses, the constituent phases found in these alloys were identified to be Al7Cu2Fe, (Al,Cu)6(Fe,Cu), α-Al12Fe3Si, Mg2Si, amorphous silicon oxide and the modified 6Fe compounds, in decreasing order of abundance. The results of quantitative X-ray microanalysis of all the constituent phases are listed in Table I. The data show that, in almost all the phases, partial substitution of alloying elements occurred resulting in small deviations from the published stoichiometric compositions of the binary and ternary compounds.

Quality monitoring system for a pulsed micro welding process on aluminum alloys

2014 ◽  
Author(s):  
Daniel Albrecht ◽  
Philipp von Witzendorff ◽  
Oliver Suttmann ◽  
Ludger Overmeyer
Keyword(s):  
Aluminum Alloys ◽  
Monitoring System ◽  
Welding Process ◽  
Quality Monitoring

Electrochemical Impedance Characteristics of Sintered 7075 Aluminum Alloy Under Ssrt Condition

2013 ◽  
Vol 58 (2) ◽  
pp. 505-508 ◽  
Author(s):  
S. Sunada ◽  
N. Nunomura
Keyword(s):  
Aluminum Alloys ◽  
Complex Shape ◽  
Electrochemical Impedance ◽  
Ingot Metallurgy ◽  
View Point ◽  
Corrosion Properties ◽  
Electrochemical Tests ◽  
Impedance Characteristics ◽  
Polarization Test ◽  
Conventional Ingot

Powder metallurgy (P/M) process has the advantage of better formability to fabricate complex shape products without machining and welding. And recently this P/M process has been applied to the production of aluminum alloys. The P/M aluminum alloys thus produced also have received considerable interest because of their fine and homogeneous structure. Many papers have been published on the mechanical properties of the aluminum alloys produced by P/M process while there have been few on their corrosion properties from the view point of electrochemistry. In this experiment, therefore, two kinds of 7075 aluminum alloys prepared by the conventional ingot metallurgy (I/M) process and P/M process were used, I/M material is commercially available. and their corrosion behavior were investigated through the electrochemical tests such as potentiodynamic polarization test, slow rate strain tensile (SSRT) test and electrochemical impedance spectroscopy (EIS) measurement under SSRT test in the corrosion solution and the deionized water.

Sign in / Sign up

Export Citation Format

Share Document