Direct Method for Evaluating Structural Needs of Flexible Pavements with Falling-Weight Deflectometer Deflections

2003 ◽  
Vol 1860 (1) ◽  
pp. 41-47 ◽  
Author(s):  
Mario S. Hoffman
Keyword(s):  
Direct Method ◽  
Flexible Pavements ◽  
Falling Weight Deflectometer ◽  
Simple Method ◽  
Traffic Demand ◽  
Structural Evaluation ◽  
Overlay Design ◽  
Subgrade Modulus ◽  
Simple Equations ◽  
Falling Weight

A direct and simple method (YONAPAVE) for evaluating the structural needs of flexible pavements is presented. It is based on interpretation of measured falling-weight deflectometer (FWD) deflection basins using mechanistic and practical approaches. YONAPAVE estimates the effective structural number (SN) and the equivalent subgrade modulus independently of the pavement or layer thicknesses. Thus, there is no need to perform boreholes, which are expensive, time-consuming, and disruptive to traffic. Knowledge of the effective SN and the subgrade modulus together with an estimate of the traffic demand allows the determination of the overlay required to accommodate future needs. YONAPAVE’s simple equations can be solved using a pocket calculator, making it suitable for rapid estimates in the field. The simplicity of the method, and its independence from major computer programs, make YONAPAVE suitable for estimating the structural needs of a road network using FWD data collected on a routine or periodic basis along network roads. YONAPAVE can be used with increased experience and confidence as the basis for nondestructive testing structural evaluation and overlay design at the project level.

Asphalt Concrete Overlay Design Case Studies

1996 ◽  
Vol 1543 (1) ◽  
pp. 3-9 ◽  
Author(s):  
Linda M. Pierce ◽  
Joe P. Mahoney
Keyword(s):  
Case Studies ◽  
Design Procedure ◽  
Washington State ◽  
Falling Weight Deflectometer ◽  
Department Of Transportation ◽  
Design Procedures ◽  
Overlay Design ◽  
Washington State Department ◽  
Falling Weight ◽  
The University

During the late 1980s, the Washington State Department of Transportation (WSDOT), the University of Washington, and the Washington State Transportation Center developed a mechanistic-empirical flexible overlay design procedure. Following development, WSDOT implemented this overlay design procedure and has been evaluating flexible overlay projects for approximately the past 8 years. WSDOT rehabilitates about 100 projects each year; approximately 20 to 30 percent of the total projects are designed using the WSDOT overlay design procedure and the AASHTO overlay design procedure (using DARWin). These two procedures are discussed in general, and two case studies illustrate each of the overlay design procedures. Also included is the backcalculation of layer moduli from falling weight deflectometer data.

scholarly journals Application of FWD data in developing dynamic modulus master curves of in-service asphalt layers

2017 ◽  
Vol 23 (5) ◽  
pp. 661-671 ◽  
Author(s):  
Nader SOLATIFAR ◽  
Amir KAVUSSI ◽  
Mojtaba ABBASGHORBANI ◽  
Henrikas SIVILEVIČIUS
Keyword(s):  
Dynamic Modulus ◽  
Master Curve ◽  
Asphalt Pavements ◽  
Falling Weight Deflectometer ◽  
Master Curves ◽  
Simple Method ◽  
High Frequencies ◽  
Design Guide ◽  
Falling Weight

This paper presents a simple method to determine dynamic modulus master curve of asphalt layers by con­ducting Falling Weight Deflectometer (FWD) for use in mechanistic-empirical rehabilitation. Ten new and rehabilitated in-service asphalt pavements with different physical characteristics were selected in Khuzestan and Kerman provinces in south of Iran. FWD testing was conducted on these pavements and core samples were taken. Witczak prediction model was used to predict dynamic modulus master curves from mix volumetric properties as well as the bitumen viscosity characteristics. Adjustments were made using FWD results and the in-situ dynamic modulus master curves were ob­tained. In order to evaluate the efficiency of the proposed method, the results were compared with those obtained by us­ing the developed procedure of the state-of-the-practice, Mechanistic-Empirical Pavement Design Guide (MEPDG). Re­sults showed the proposed method has several advantages over MEPDG including: (1) simplicity in directly constructing in-situ dynamic modulus master curve; (2) developing in-situ master curve in the same trend with the main predicted one; (3) covering the large differences between in-situ and predicted master curve in high frequencies; and (4) the value obtained for the in-situ dynamic modulus is the same as the value measured by the FWD for a corresponding frequency.

Dynamic Interpretation for Impulsive Deflection Test on Flexible Pavements

1998 ◽  
Vol 14 (2) ◽  
pp. 91-100
Author(s):  
Der-Wen Chang ◽  
Chia-Ling Chang
Keyword(s):  
Iterative Scheme ◽  
Flexible Pavements ◽  
Falling Weight Deflectometer ◽  
Correction Procedure ◽  
Subgrade Soils ◽  
Forward Analysis ◽  
Dynamic Interpretation ◽  
Equivalent Number ◽  
Deflection Test ◽  
Falling Weight

AbstractIn this study, a computer program DBFWD is developed for data analysis of Falling Weight Deflectometer (FWD) test on flexible pavements. To backcalculate the layer moduli of the pavement, a number of iterative backcalculation schemes were employed with the forward analysis of the Green's flexibility influence functions. The temperature and the moisture influences on material moduli of the asphalt surface and the subgrade soils were considered in the analysis. As the result, the iterative scheme based on the peak deflection ratios was selected to backcalculate the layer moduli of local pavements. Owing to the correction procedure used in the program, interpretations with four original deflections were found more accurate than those with equivalent number of modified deflections. Comparisons of program DBFWD with other static backcalculation programs on theoretical and experimental deflections indicated that dynamic interpretation is more effective in providing the layer modulus information. Despite of the requirements of accurate inputs of the layer thickness and the testing load for the analysis, a generalized application of the program needs to be clarified with model road test in demand.

Mechanistically Based Flexible Overlay Design System for Idaho

1996 ◽  
Vol 1543 (1) ◽  
pp. 10-19 ◽  
Author(s):  
Fouad M. Bayomy ◽  
Fawzi A. Al-Kandari ◽  
Robert M. Smith
Keyword(s):  
Design Procedure ◽  
Failure Criteria ◽  
The State ◽  
Design System ◽  
Falling Weight Deflectometer ◽  
Overlay Design ◽  
Pavement Damage ◽  
Critical Strains ◽  
Falling Weight ◽  
User Friendly

A study was conducted on a mechanistically based overlay design procedure that incorporates the in situ pavement layer modulus values evaluated by deflection-based nondestructive testing using falling weight deflectometer data. The proposed overlay design procedure addresses the seasonal variation in the state of Idaho and adjusts the modulus values accordingly. The performance of the pavement is calculated in terms of critical strains based on the elastic multilayer theory. The study adopts the Asphalt Institute fatigue and rutting failure criteria to calculate the life of the pavement. Damage analysis is performed based on the past and expected future traffic to calculate the required overlay thickness. The procedure developed has been implemented in an event-driven, user-friendly computer program FLEXOLAY, which runs in the DOS environment. The program was tested and compared with other overlay design methods using pavement sections from the state of Idaho. The overlay thickness determined by FLEXOLAY was found to be close to some of the existing methods and far from others, depending on the existing pavement conditions.

Visco-Elastic Back-Calculation of Traffic Speed Deflectometer Measurements

2019 ◽  
Vol 2673 (12) ◽  
pp. 439-448 ◽  
Author(s):  
Christoffer P. Nielsen
Keyword(s):  
Calculation Procedure ◽  
Falling Weight Deflectometer ◽  
Calculation Algorithm ◽  
Structural Evaluation ◽  
Driving Speed ◽  
Back Calculation ◽  
Traffic Speed ◽  
Falling Weight ◽  
Calculation Procedures ◽  
Project Level

The traffic speed deflectometer (TSD) has proven a valuable tool for network level structural evaluation. At the project level, however, the use of TSD data is still quite limited. An obstacle to the use of TSD at the project level is that the standard approaches to back-calculation of pavement properties are based on the falling weight deflectometer (FWD). The FWD experiment is similar, but not equivalent, to the TSD experiment, and therefore it is not straightforward to apply the traditional FWD back-calculation procedures to TSD data. In this paper, a TSD-specific back-calculation procedure is presented. The procedure is based on a layered linear visco-elastic pavement model and takes the driving speed of the vehicle into account. This is in contrast to most existing back-calculation procedures, which treat the problem as static and the pavement as purely elastic. The developed back-calculation procedure is tested on both simulated and real TSD data. The real TSD measurements exhibit significant effects of damping and visco-elasticity. The back-calculation algorithm is able to capture these effects and yields model fits in excellent agreement with the measured values.

A practical approach to falling-weight deflectometer (FWD) data reduction

2005 ◽  
Vol 42 (2) ◽  
pp. 641-645 ◽  
Author(s):  
Dieter Stolle ◽  
Peijun Guo
Keyword(s):  
Mechanical Properties ◽  
Shear Modulus ◽  
Falling Weight Deflectometer ◽  
Layer System ◽  
Surface Loading ◽  
Back Calculation ◽  
Pavement Response ◽  
Subgrade Modulus ◽  
Falling Weight

The authors present a simplified methodology for preprocessing falling-weight deflectometer (FWD) data, which identify a pseudo-static pavement response to surface loading. This allows one to employ static analysis to back-calculate the mechanical properties of the pavement–subgrade system. It is shown that the subgrade modulus can be identified, independent of the details of the pavement structure itself, at least for a two-layer system. The quality of the effective shear modulus is sensitive to the value of Poisson's ratio selected.Key words: pavement–subgrade system, subgrade modulus, back-calculation, FWD.

Interpretation of pavement deflection measurement data using an elastodynamic stochastic approach

1998 ◽  
Vol 25 (1) ◽  
pp. 151-160 ◽  
Author(s):  
Mehdi Parvini ◽  
Dieter FE Stolle
Keyword(s):  
Finite Element ◽  
Measurement Data ◽  
Stochastic Approach ◽  
Falling Weight Deflectometer ◽  
Stochastic Finite Element ◽  
Element Approach ◽  
Subgrade Modulus ◽  
Low Sensitivity ◽  
Falling Weight ◽  
Surface Deflections

Pavement deflection measurements, together with backcalculation procedures, are widely used to estimate the layer moduli of pavement-subgrade systems. Sensitivity analysis of a sample problem indicates that conclusions drawn from static analyses with regards to deflection sensitivity to variation in layer moduli may apply when characterizing uncertainty associated with the interpretation of the falling weight deflectometer (FWD) data. The uncertainty associated with the values of the backcalculated parameters from deflection data is investigated in this paper using an elastodynamic, stochastic finite element approach. The results of the simulations indicate that, in order to properly estimate surface layer moduli, loading frequencies higher than that of excitation by typical FWD loading are required. The low sensitivity of deflection uncertainty to random variations in surface modulus, when compared with that associated with subgrade modulus, is demonstrated to contribute to high variations in backcalculated surface modulus from measured surface deflections. Although focus is placed on uncertainties in elastic modulus and deflection, the methodology presented in the paper can be used to quantify uncertainties associated with other layer properties and pavement responses.Key words: stochastic, finite element, pavement deflection, elastodynamic, backcalculation, layer moduli, falling weight deflectometer test.

Field Assessment of Changes in Pavement Moduli Caused by Freezing and Thawing

1998 ◽  
Vol 1615 (1) ◽  
pp. 41-48 ◽  
Author(s):  
Da-Tong Jong ◽  
Peter J. Bosscher ◽  
Craig H. Benson
Keyword(s):  
Flexible Pavements ◽  
Complete Recovery ◽  
Meteorological Conditions ◽  
Phase Changes ◽  
Water Phase ◽  
Falling Weight Deflectometer ◽  
Freezing And Thawing ◽  
Field Assessment ◽  
Falling Weight ◽  
Water Contents

Three secondary highways with flexible pavements were instrumented for 18 months to monitor changes in pavement moduli caused by seasonal meteorological changes. Temperatures, water contents, and water phase changes in the subsurface as well as meteorological conditions were recorded every 2 hours throughout the study. Pavement moduli were regularly determined by conducting surveys with a falling weight deflectometer and by performing backcalculations using the program Modulus. The moduli of the base and subgrade typically increased 12 to 4 times, respectively, when frost penetrated the subsurface. When the base and subgrade began to thaw, the moduli decreased substantially. The base moduli decreased the most, typically being about 35 percent of the prefreezing values by the end of thaw. Smaller decreases occurred in the subgrade. The subgrade moduli were about 65 percent of their prefreezing values by the end of thaw. The moduli continued to decrease until thaw was complete and then gradually recovered back to the original prefreezing values. Complete recovery required approximately 4 months. Similar changes in moduli were observed regardless of site or year.

Sign in / Sign up

Export Citation Format

Share Document