scholarly journals Evidence for deep icequakes in an Alpine glacier

2000 ◽  
Vol 31 ◽  
pp. 85-90 ◽  
Author(s):  
N. Deichmann ◽  
J. Ansorge ◽  
F. Scherbaum ◽  
A. Aschwanden ◽  
F. Bernard ◽  
...  
Keyword(s):  
Rayleigh Wave ◽  
Three Dimensional ◽  
Focal Depth ◽  
Vertical Component ◽  
Swiss Alps ◽  
P Wave ◽  
S Wave ◽  
Glacier Surface ◽  
Simultaneous Inversion ◽  
Wave Velocities

AbstractTo obtain more reliable information about the focal-depth distribution of icequakes, in April 1997 we operated an array of seven portable digital seismographs on Unteraargletscher, central Swiss Alps. Over 5000 events were detected by at least two instruments during the 9 day recording period. P-wave velocities (3770 m f) were determined from several calibration shots detonated at the glacier surface as well as in a 49 m deep borehole, whereas S-wave velocities (1860 ms–1) were derived from a simultaneous inversion for Vp/Vs6 applied to 169 icequakes. So far, hypocentral locations have been calculated for over 300 icequakes. Besides confirming the occurrence of shallow events associated with the opening of crevasses, our results show that a small but significant fraction of the hypocenters are located at or near the glacier bed. One event was found at an intermediate depth of about 120 m. Three-dimensional particle-motion diagrams of both explosions and icequakes clearly demonstrate that all vertical component seismograms from shallow sources are dominated by the Rayleigh wave. On the other hand, for events occurring at depths greater than about 40 m, the Rayleigh wave disappears almost entirely. Therefore, a qualitative analysis of the signal character provides direct information on the focal depth of an event and was used as an independent check of the locations obtained from traditional arrival-time inversions. Thus, our results demonstrate that deep icequakes do occur and that simple rheological models, according to which brittle deformation is restricted to the uppermost part of a glacier, may need revision.

Dispersion patterns of the ground roll in eastern Saudi Arabia

Geophysics ◽  
1981 ◽  
Vol 46 (2) ◽  
pp. 121-137 ◽  
Author(s):  
Moujahed I. Al‐Husseini ◽  
Jon B. Glover ◽  
Brian J. Barley
Keyword(s):  
Saudi Arabia ◽  
Rayleigh Wave ◽  
Wavelength Range ◽  
Noise Analysis ◽  
Regional Scale ◽  
P Wave ◽  
S Wave ◽  
Wave Velocities ◽  
Ground Roll ◽  
P Wave Velocities

Seismic surveys on land must be designed so that the source‐generated noise, such as ground roll, is preferentially attenuated before P‐wave signal amplification and recording. The correct specification of spatial and frequency filters requires prior knowledge of the noise properties in the area. We show that the strong Rayleigh wave component of source‐generated noise has a wavelength range which is predictable on a regional scale, using widespread P‐wave velocity measurements in shallow upholes. This predictive capability decreases the number of noise analyses required to map the boundaries between areas with different Rayleigh wave properties. The case history presented is for northeastern Saudi Arabia, an area of roughly [Formula: see text]. The data comprise 80 noise analyses and a data base of over 10,000 up‐hole measurements of P‐wave velocities, supplemented by maps of topography and geologic outcrops. Examples show that the frequency‐wavenumber transforms of time‐offset records can be interpreted in detail in terms of Rayleigh wave dispersion and air wave coupling, dictated by the elastic properties of the very shallow layers. P‐wave velocities, measured in shallow upholes at noise analysis sites, are used to form initial estimates of the corresponding shear‐wave velocities and subsequently refined by matching the observed and predicted dispersion curves. Even without this refinement process, the initial S‐wave velocities can be used to estimate Rayleigh wave velocities at frequencies which typify the top and bottom of current vibrator sweeps (10 and 80 Hz). These velocities are mapped for the area and used to determine the wavelength range of Rayleigh waves. An effort is also made to map regions where Rayleigh wave scattering from surface topography is likely to occur.

Local and global fluid effects on sonic wave modes

Geophysics ◽  
2017 ◽  
Vol 82 (6) ◽  
pp. D369-D381 ◽  
Author(s):  
Elliot J. H. Dahl ◽  
Kyle T. Spikes
Keyword(s):  
Rayleigh Wave ◽  
Wave Velocity ◽  
Fluid Pressure ◽  
Wave Mode ◽  
P Wave ◽  
Stoneley Wave ◽  
S Wave ◽  
Local Pressure ◽  
Wave Velocities ◽  
Wave Modes

Most subsurface formations of value to exploration contain a heterogeneous fluid-filled pore space, where local fluid-pressure effects can significantly change the velocities of passing seismic waves. To better understand the effect of these local pressure gradients on borehole wave propagation, we combined Chapman’s squirt-flow model with Biot’s poroelastic theory. We applied the unified theory to a slow and fast formation with permeable borehole walls containing different quantities of compliant pores. These results are compared with those for a formation with no soft pores. The discrete wavenumber summation method with a monopole point source generates the wavefields consisting of the P-, S-, leaky-P, Stoneley, and pseudo-Rayleigh waves. The resulting synthetic wave modes are processed using a weighted spectral semblance (WSS) algorithm. We found that the resulting WSS dispersion curves closely matched the analytical expressions for the formation compressional velocity and solutions to the period equation for dispersion for the P-wave, Stoneley-wave, and pseudo-Rayleigh wave phase velocities in the slow and fast formations. The WSS applied to the S-wave part of the waveforms, however, did not correlate as well with its respective analytical expression for formation S-wave velocity, most likely due to interference of the pseudo-Rayleigh wave. To separate changes in formation P- and S-wave velocities versus fluid-flow effects on the Stoneley-wave mode, we computed the slow-P wave dispersion for the same formations. We found that fluid-saturated soft pores significantly affected the P- and S-wave effective formation velocities, whereas the slow-P wave velocity was rather insensitive to the compliant pores. Thus, the large phase-velocity effect on the Stoneley wave mode was mainly due to changes in effective formation P- and S-wave velocities and not to additional fluid mobility.

Numerical and Theoretical Investigation on the Origin of the Multiple Peaks of the H/V Ratio Curve

2021 ◽  
Author(s):  
Wanbo Xiao ◽  
Siqi Lu ◽  
Yanbin Wang
Keyword(s):  
Rayleigh Wave ◽  
Wave Velocity ◽  
Subsurface Layer ◽  
P Wave ◽  
Theoretical Formula ◽  
S Wave ◽  
Multiple Peaks ◽  
Ratio Curve ◽  
Multiple Layer ◽  
Wave Resonance

<p>Despite the popularity of the horizontal to vertical spectral ratio (HVSR) method in site effect studies, the origin of the H/V peaks has been controversial since this method was proposed. Many previous studies mainly focused on the explanation of the first or single peak of the H/V ratio, trying to distinguish between the two hypotheses — the S-wave resonance and ellipticity of Rayleigh wave. However, it is common both in numerical simulations and practical experiments that the H/V ratio exhibits multiple peaks, which is essential to explore the origin of the H/V peaks.</p><p>The cause for the multiple H/V peaks has not been clearly figured out, and once was simply explained as the result of multi subsurface layers. Therefore, we adopted numerical method to simulate the ambient noise in various layered half-space models and calculated the H/V ratio curves for further comparisons. The peak frequencies of the H/V curves accord well with the theoretical frequencies of S-wave resonance in two-layer models, whose frequencies only depend on the S wave velocity and the thickness of the subsurface layer. The same is true for models with varying model parameters. Besides, the theoretical formula of the S-wave resonance in multiple-layer models is proposed and then supported by numerical investigations as in the cases of two-layer models. We also extended the S-wave resonance to P-wave resonance and found that its theoretical frequencies fit well with the V/H peaks, which could be an evidence to support the S-wave resonance theory from a new perspective. By contrast, there are obvious differences between the higher orders of the H/V ratio peaks and the higher orders of Rayleigh wave ellipticity curves both in two-layer and multiple-layer models. The Rayleigh wave ellipticity curves are found to be sensitive to the Poisson’s ratio and the thickness of the subsurface layer, so the variation of the P wave velocity can affect the peak frequencies of the Rayleigh wave ellipticity curves while the H/V peaks show slight change. The Rayleigh wave ellipticity theory is thus proved to be inappropriate for the explanation of the multiple H/V peaks, while the possible effects of the Rayleigh wave on the fundamental H/V peak still cannot be excluded.</p><p>Based on the analyses above, we proposed a new evidence to support the claim that the peak frequencies of the H/V ratio curve, except the fundamental peaks, are caused by S-wave resonance. The relationship between the P-wave resonance and the V/H peaks may also find further application.</p>

scholarly journals Metode Seismik dalam Pemodelan Fisis Letusan Gunung Lumpur Bledug Kuwu

2019 ◽  
Vol 2 (2) ◽  
pp. 61-66
Author(s):  
Ahmad Fauzi Pohan ◽  
Rusnoviandi Rusnoviandi
Keyword(s):  
Wave Velocity ◽  
Physical Modeling ◽  
Vertical Component ◽  
Dominant Frequency ◽  
P Wave ◽  
Physical Parameters ◽  
S Wave ◽  
Interesting Phenomenon ◽  
Central Java ◽  
P Wave Velocity

Aktivitas gunung lumpur Bledug Kuwu di Jawa  Tengah merupakan fenomena yang menarik dikaji menggunakan pemodelan fisis. Tujuan penelitian ini adalah mengetahui parameter dari medium gunung lumpur Bledug Kuwu. Adapun pemodelan fisis yang dilakukan dengan menggunakan media fisis akuarium berukuran 59 × 59 × 37,3 cm yang diisi material dari lumpur Bledug Kuwu. Sumber letusan dihasilkan dari tekanan kompresor yang dapat diatur kedalaman (10.5, 13, dan 15.5 cm) dan sudut (30o, 45o dan 60o) sumbernya. Sensor yang digunakan geophone komponen vertikal sebanyak 3 buah dengan durasi perekaman selama 5 dan 2,5 detik. Data diambil dengan frekuensi sampel 2 dan 4 kHz untuk masing-masing durasi perekaman. Konfigurasi sumber dan geophone dibuat sesuai dengan pemodelan fisisnya. Pengukuran desnsitas lumpur menunjukkan angka sebesar 1200 kg/m3. Berdasarkan hasil analisis seismogram model fisis diperoleh kecepatan perambatan gelombang-P pada medium lumpur Bledug Kuwu adalah sebesar 48,74 m/s,dan gelombang-S sebesar 28,14 m/s dengan frekuensi dominan antara 20 sampai 25 Hz.   Bledug Kuwu mud volcano activity in Central Java is an interesting phenomenon to be studied using both physical  modeling. The objective of this study was to determine the physical parameters of the medium of Bledug Kuwu. The Physical model was an aquarium with a dimension of 59 × 59 × 37.3 cm filled with Bledug Kuwu’s mud. The eruption source is generated by a compressor pressure that can be controled both the depth(10.5, 13, and 15.5 cm) and the angel of the source (30o, 45o and 60o). The resulting seismic signals were recorded by using 3 vertical component geophones for 10 and 5 seconds durations at a frequency of 2 and 4 kHz respectivel, mud density 1200 kg/m3 . The physical modeling shows that the P-wave velocity of the Bledug Kuwu’s medium is 48.7 m/s, S-wave velocity of Bledug Kuwu’s is 28,14 m/s  with a dominant frequency of 20 to 25 Hz.

Shallow velocity structure and poisson's ratio at the Tarzana, California, strong-motion accelerometer site

1996 ◽  
Vol 86 (6) ◽  
pp. 1704-1713 ◽  
Author(s):  
R. D. Catchings ◽  
W. H. K. Lee
Keyword(s):  
Urban Areas ◽  
Velocity Structure ◽  
Strong Motion ◽  
P Wave ◽  
S Wave ◽  
Near Surface ◽  
Velocity Models ◽  
Wave Velocities ◽  
Poisson's Ratios ◽  
Poisson’S Ratios

Abstract The 17 January 1994, Northridge, California, earthquake produced strong ground shaking at the Cedar Hills Nursery (referred to here as the Tarzana site) within the city of Tarzana, California, approximately 6 km from the epicenter of the mainshock. Although the Tarzana site is on a hill and is a rock site, accelerations of approximately 1.78 g horizontally and 1.2 g vertically at the Tarzana site are among the highest ever instrumentally recorded for an earthquake. To investigate possible site effects at the Tarzana site, we used explosive-source seismic refraction data to determine the shallow (<70 m) P-and S-wave velocity structure. Our seismic velocity models for the Tarzana site indicate that the local velocity structure may have contributed significantly to the observed shaking. P-wave velocities range from 0.9 to 1.65 km/sec, and S-wave velocities range from 0.20 and 0.6 km/sec for the upper 70 m. We also found evidence for a local S-wave low-velocity zone (LVZ) beneath the top of the hill. The LVZ underlies a CDMG strong-motion recording site at depths between 25 and 60 m below ground surface (BGS). Our velocity model is consistent with the near-surface (<30 m) P- and S-wave velocities and Poisson's ratios measured in a nearby (<30 m) borehole. High Poisson's ratios (0.477 to 0.494) and S-wave attenuation within the LVZ suggest that the LVZ may be composed of highly saturated shales of the Modelo Formation. Because the lateral dimensions of the LVZ approximately correspond to the areas of strongest shaking, we suggest that the highly saturated zone may have contributed to localized strong shaking. Rock sites are generally considered to be ideal locations for site response in urban areas; however, localized, highly saturated rock sites may be a hazard in urban areas that requires further investigation.

On the ratio of P-wave to S-wave corner frequencies for shallow earthquake sources

1974 ◽  
Vol 64 (4) ◽  
pp. 1159-1180 ◽  
Author(s):  
F. A. Dahlen
Keyword(s):  
Single Point ◽  
Three Dimensional ◽  
P Wave ◽  
Corner Frequency ◽  
S Wave ◽  
Earthquake Sources ◽  
Kinematical Model ◽  
Self Similar ◽  
Smooth Deceleration ◽  
Shallow Focus

abstract We construct a theoretical three-dimensional kinematical model of shallow-focus earthquake faulting in order to investigate the ratio of the P- and S-wave corner frequencies of the far-field elastic radiation. We attempt to incorporate in this model all of the important gross kinematical features which would arise if ordinary mechanical friction should be the dominant traction resisting fault motion. These features include a self-similar nucleation at a single point, a subsonic spreading of rupture away from that point, and a termination of faulting by smooth deceleration. We show that the ratio of the P-wave corner frequency to the S-wave corner frequency for any model which has these features will be less than unity at all points on the focal sphere.

Temperate Alpine glacier surface dynamics linked to collapsing subglacial conduits

2021 ◽  
Author(s):  
Pascal Egli ◽  
Stuart Lane ◽  
James Irving ◽  
Bruno Belotti
Keyword(s):  
Three Dimensional ◽  
Swiss Alps ◽  
Glacier Retreat ◽  
Collapse Mechanism ◽  
Glacier Mass Balance ◽  
Glacier Surface ◽  
Alpine Glacier ◽  
Surface Loss ◽  
Ice Surface ◽  
Surface Melt

<p>If tongues of temperate Alpine glaciers are subjected to high temperatures their topography may change rapidly due to the effects of differential melt related to aspect and debris cover. Independent of local surface melt, the position of subglacial conduits may have an important influence on ice creep and so on changes in topography at the ice surface. This reflects analyses that suggest that subglacial conduits at glacier margins may not be permanently pressurised; and that creep closure rates are insufficient to close subglacial conduits completely. Rapid climate warming may exacerbate this process, due both to surface-melt driven glacier thinning and over-enlargement of conduits due to high upstream melt rates. Over-enlarged conduits that are not permanently pressurised would lead to the development of structural weaknesses and eventual collapse of the ice surface into the conduits. We hypothesise that this collapse mechanism could represent an important and alternative driver of rapid glacier retreat.</p><p>In this paper we combine: (1) an extensive survey of glacier margin collapse in the Swiss Alps with (2) intensive monitoring of the dynamics of such collapse at the Otemma Glacier in the south-western Swiss Alps. Daily UAV surveys were undertaken at a high spatial resolution and with precise and accurate ground control. These datasets were used to generate surface change information using SfM-MVS photogrammetry. Surfaces of difference showed surface loss that could not be related to ablation alone. Combining them with three-dimensional ground-penetrating radar (GPR) surveys in the same zone showed that the surface loss was coincident spatially with the positions of sub-glacial conduits, for ice thicknesses between 20 m and 50 m. We show that this form of subglacial conduit collapse is also happening for several other glaciers in the Swiss Alps, and that this mechanism of snout collapse and glacier retreat has become more common than has hitherto been the case. It also leads to temporal patterns of glacier margin retreat that differ from those that might be expected due to glacier mass balance and ice mass flux effects alone.</p>

scholarly journals A method of geo-acoustic parameter inversion in shallow sea by the Bayesian theory and the acoustic pressure field

2019 ◽  
Vol 283 ◽  
pp. 06003
Author(s):  
Guangxue Zheng ◽  
Hanhao Zhu ◽  
Jun Zhu
Keyword(s):  
Sound Pressure ◽  
Pressure Field ◽  
Wave Attenuation ◽  
Acoustic Parameter ◽  
Bayesian Theory ◽  
P Wave ◽  
Shallow Sea ◽  
S Wave ◽  
Wave Velocities ◽  
Parameter Inversion

A method of geo-acoustic parameter inversion based on the Bayesian theory is proposed for the acquisition of acoustic parameters in shallow sea with the elastic seabed. Firstly, the theoretical prediction value of the sound pressure field is calculated by the fast field method (FFM). According to the Bayesian theory, we establish the misfit function between the measured sound pressure field and the theoretical pressure field. It is under the assumption of Gaussian data errors which are in line with the likelihood function. Finally, the posterior probability density (PPD) of parameters is given as the result of inversion. Our research is conducted in the light of Metropolis sample rules. Apart from numerical simulations, a scaled model experiment has been taken in the laboratory tank. The results of numerical simulations and tank experiments show that sound pressure field calculated by the result of inversion is consistent with the measured sound pressure field. Besides, s-wave velocities, p-wave velocities and seafloor density have fewer uncertainties and are more sensitive to complex sound pressure than s-wave attenuation and p-wave attenuation. The received signals calculated by inversion results are keeping with received signals in the experiment which verify the effectiveness of this method.

EXTRACTING SUB-SURFACE INFORMATION FROM LONG OFFSET P-WAVE DATA—A CHEAPER ALTERNATIVE TO MULTICOMPONENT OBC FOR EXPLORATION?

2002 ◽  
Vol 42 (1) ◽  
pp. 627
Author(s):  
R.G. Williams ◽  
G. Roberts ◽  
K. Hawkins
Keyword(s):  
Seismic Energy ◽  
Higher Order ◽  
P Wave ◽  
S Wave ◽  
Additional Information ◽  
Wave Data ◽  
Wave Velocities ◽  
Avo Inversion ◽  
Long Offset ◽  
Multicomponent Data

Seismic energy that has been mode converted from pwave to s-wave in the sub-surface may be recorded by multi-component surveys to obtain information about the elastic properties of the earth. Since the energy converted to s-wave is missing from the p-wave an alternative to recording OBC multi-component data is to examine p-wave data for the missing energy. Since pwave velocities are generally faster than s-wave velocities, then for a given reflection point the converted s-wave signal reaches the surface at a shorter offset than the equivalent p-wave information. Thus, it is necessary to record longer offsets for p-wave data than for multicomponent data in order to measure the same information.A non-linear, wide-angle (including post critical) AVO inversion has been developed that allows relative changes in p-wave velocities, s-wave velocities and density to be extracted from long offset p-wave data. To extract amplitudes at long offsets for this inversion it is necessary to image the data correctly, including correcting for higher order moveout and possibly anisotropy if it is present.The higher order moveout may itself be inverted to yield additional information about the anisotropy of the sub-surface.

Sign in / Sign up

Export Citation Format

Share Document