scholarly journals Pengaruh Kelengkungan Sudu Terhadap Kinerja Turbin Angin Savonius

2019 ◽  
Vol 6 (2) ◽  
pp. 139
Author(s):  
Jamal Jamal ◽  
A. M. Shiddiq Yunus ◽  
Lewi Lewi
Keyword(s):  
Wind Speed ◽  
Wind Turbines ◽  
Power Output ◽  
Input Power ◽  
Load Force ◽  
Maximum Efficiency ◽  
Wind Speeds ◽  
Energy Needs ◽  
Turbine Shaft ◽  
Lower Torque

Savonius wind turbine is one of the wind turbines that is more widely used for low energy needs, with more energy needs, this turbine type is very feasible to be developed. This research aims to improve the performance of Savonius wind turbines with variations in turbine blade curvature and variations in wind speed. The research method is a laboratory experiment on the fan test, the blade curvature test variation is 1R; 1.5R and 2R, another variation is the wind speed which are 4.0; 5.5; 7.0 and 8.5 m/s. The experiement results shows that the greater the wind speed, the input power, air mass flow velocity, power output, and efficiency will be even greater; the greater the load force on the turbine shaft, the torque on the turbine shaft will also be greater; the relationship of force loads to power output and turbine efficiency is to construct a parabolic curve; for the same wind speed, the 2R turbine has the lowest rotation, power output and efficiency compared to the 1R and 1.5R turbines; at the same wind speed the 1R turbine produces a higher rotation but requires lower torque than the 1.5R turbine; at low wind speeds (4 m / s) the 1.5R turbine has better efficiency than the 1R turbine, whereas at the high wind speed (8.5 m/s) the 1R turbine has a better efficiency than the 1.5R turbine; The maximum efficiency is obtained at 89.56% in the 1R curvature turbine with a wind speed of 8.5 m / s.

Analysis of a Concept for a Low Wind Speed Tolerant Axial Wind Turbine

2011 ◽  
Author(s):  
Ali A. Ameri ◽  
Majid Rashidi
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Power Output ◽  
Turbine Rotor ◽  
Navier Stokes ◽  
Ambient Wind ◽  
Wind Speeds ◽  
Low Wind Speed ◽  
Low Wind Speeds

In this paper, the authors analyze a design for a wind tower intended for areas of low wind speeds. The wind tower consists of a combination of several rooftop size turbines arranged alongside a cylindrical structure that acts as a Wind Deflecting Structure (WDS). The WDS amplifies the effective wind speed thus allowing the turbine rotors to operate under lower ambient wind speeds. Analyses were performed using simple models as well as more sophisticated CFD methods employing Steady and Unsteady Reynolds Averaged Navier-Stokes methodology. The effect of the wind amplification was shown on a commercial small wind turbine power output map. Also, a wind turbine rotor flow was computed as operating alongside the WDS and compared to the computed operation of isolated turbines at equal effective and ambient wind velocities. The computational analyses of this work suggest that the power output of isolated rooftop wind turbines deployed at low to moderate wind speed may be matched by installing wind turbines alongside a cylindrical wind deflecting structure operating at lower wind speeds. Other benefits of the arrangement are also enumerated.

SHAPING OF AN AUTONOMOUS POWER SYSTEM FOR GUARANTEED POWER SUPPLY WITH THE PREDOMINANCE WIND ENERGY

2018 ◽  
pp. 28-50
Author(s):  
S. G. Ignatiev ◽  
S. V. Kiseleva
Keyword(s):  
Energy Storage ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Demand ◽  
Diesel Generator ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind

Optimization of the autonomous wind-diesel plants composition and of their power for guaranteed energy supply, despite the long history of research, the diversity of approaches and methods, is an urgent problem. In this paper, a detailed analysis of the wind energy characteristics is proposed to shape an autonomous power system for a guaranteed power supply with predominance wind energy. The analysis was carried out on the basis of wind speed measurements in the south of the European part of Russia during 8 months at different heights with a discreteness of 10 minutes. As a result, we have obtained a sequence of average daily wind speeds and the sequences constructed by arbitrary variations in the distribution of average daily wind speeds in this interval. These sequences have been used to calculate energy balances in systems (wind turbines + diesel generator + consumer with constant and limited daily energy demand) and (wind turbines + diesel generator + consumer with constant and limited daily energy demand + energy storage). In order to maximize the use of wind energy, the wind turbine integrally for the period in question is assumed to produce the required amount of energy. For the generality of consideration, we have introduced the relative values of the required energy, relative energy produced by the wind turbine and the diesel generator and relative storage capacity by normalizing them to the swept area of the wind wheel. The paper shows the effect of the average wind speed over the period on the energy characteristics of the system (wind turbine + diesel generator + consumer). It was found that the wind turbine energy produced, wind turbine energy used by the consumer, fuel consumption, and fuel economy depend (close to cubic dependence) upon the specified average wind speed. It was found that, for the same system with a limited amount of required energy and high average wind speed over the period, the wind turbines with lower generator power and smaller wind wheel radius use wind energy more efficiently than the wind turbines with higher generator power and larger wind wheel radius at less average wind speed. For the system (wind turbine + diesel generator + energy storage + consumer) with increasing average speed for a given amount of energy required, which in general is covered by the energy production of wind turbines for the period, the maximum size capacity of the storage device decreases. With decreasing the energy storage capacity, the influence of the random nature of the change in wind speed decreases, and at some values of the relative capacity, it can be neglected.

scholarly journals Performance Enhancement of Proposed Namaacha Wind Farm by Minimising Losses Due to the Wake Effect: A Mozambican Case Study

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4291
Author(s):  
Paxis Marques João Roque ◽  
Shyama Pada Chowdhury ◽  
Zhongjie Huan
Keyword(s):  
Wind Speed ◽  
Wind Power ◽  
Wind Turbines ◽  
Power Output ◽  
Wind Farm ◽  
Wind Farms ◽  
Operating Conditions ◽  
Wake Effect ◽  
Wind Generators ◽  
Wind Potential

District of Namaacha in Maputo Province of Mozambique presents a high wind potential, with an average wind speed of around 7.5 m/s and huge open fields that are favourable to the installation of wind farms. However, in order to make better use of the wind potential, it is necessary to evaluate the operating conditions of the turbines and guide the independent power producers (IPPs) on how to efficiently use wind power. The investigation of the wind farm operating conditions is justified by the fact that the implementation of wind power systems is quite expensive, and therefore, it is imperative to find alternatives to reduce power losses and improve energy production. Taking into account the power needs in Mozambique, this project applied hybrid optimisation of multiple energy resources (HOMER) to size the capacity of the wind farm and the number of turbines that guarantee an adequate supply of power. Moreover, considering the topographic conditions of the site and the operational parameters of the turbines, the system advisor model (SAM) was applied to evaluate the performance of the Vestas V82-1.65 horizontal axis turbines and the system’s power output as a result of the wake effect. For any wind farm, it is evident that wind turbines’ wake effects significantly reduce the performance of wind farms. The paper seeks to design and examine the proper layout for practical placements of wind generators. Firstly, a survey on the Namaacha’s electricity demand was carried out in order to obtain the district’s daily load profile required to size the wind farm’s capacity. Secondly, with the previous knowledge that the operation of wind farms is affected by wake losses, different wake effect models applied by SAM were examined and the Eddy–Viscosity model was selected to perform the analysis. Three distinct layouts result from SAM optimisation, and the best one is recommended for wind turbines installation for maximising wind to energy generation. Although it is understood that the wake effect occurs on any wind farm, it is observed that wake losses can be minimised through the proper design of the wind generators’ placement layout. Therefore, any wind farm project should, from its layout, examine the optimal wind farm arrangement, which will depend on the wind speed, wind direction, turbine hub height, and other topographical characteristics of the area. In that context, considering the topographic and climate features of Mozambique, the study brings novelty in the way wind farms should be placed in the district and wake losses minimised. The study is based on a real assumption that the project can be implemented in the district, and thus, considering the wind farm’s capacity, the district’s energy needs could be met. The optimal transversal and longitudinal distances between turbines recommended are 8Do and 10Do, respectively, arranged according to layout 1, with wake losses of about 1.7%, land utilisation of about 6.46 Km2, and power output estimated at 71.844 GWh per year.

scholarly journals Wind Turbulence Intensity at La Ventosa, Mexico: A Comparative Study with the IEC61400 Standards

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3007 ◽  
Author(s):  
C. Lopez-Villalobos ◽  
O. Rodriguez-Hernandez ◽  
R. Campos-Amezcua ◽  
Guillermo Hernandez-Cruz ◽  
O. Jaramillo ◽  
...  
Keyword(s):  
Wind Speed ◽  
Wind Turbines ◽  
Turbulence Intensity ◽  
Structural Damage ◽  
Atmospheric Stability ◽  
Design Parameters ◽  
Power Sector ◽  
Wind Speeds ◽  
Technical Solutions ◽  
Large Wind

Wind speed turbulence intensity is a crucial parameter in designing the structure of wind turbines. The IEC61400 considers the Normal Turbulence Model (NTM) as a reference for fatigue load calculations for small and large wind turbines. La Ventosa is a relevant region for the development of the wind power sector in Mexico. However, in the literature, there are no studies on this important parameter in this zone. Therefore, we present an analysis of the turbulence intensity to improve the understanding of local winds and contribute to the development of reliable technical solutions. In this work, we experimentally estimate the turbulence intensity of the region and the wind shear exponent in terms of atmospheric stability to analyze the relation of these design parameters with the recommended standard for large and small wind turbines. The results showed that the atmosphere is strongly convective and stable in most of the eleven months studied. The turbulence intensity analysis showed that for a range of wind speeds between 2 and 24 m/s, some values of the variable measured were greater than those recommended by the standard, which corresponds to 388 hours of turbulence intensity being underestimated. This may lead to fatigue loads and cause structural damage to the technologies installed in the zone if they were not designed to operate in these wind speed conditions.

Analysis of Wind Field Fan Based on Performance Enhancement Method

2014 ◽  
Vol 986-987 ◽  
pp. 235-238
Author(s):  
Xiao Long Tan ◽  
Jia Zhou ◽  
Wen Bin Wang
Keyword(s):  
Wind Speed ◽  
Wind Turbines ◽  
Performance Enhancement ◽  
Aerodynamic Performance ◽  
Wind Load ◽  
Wind Speeds ◽  
Enhancement Method ◽  
Changes Over Time ◽  
Load Simulation ◽  
Single Constant

For the simulation of wind turbine, the wind speed is extremely important parameters and indicators to measure the output power of the unit is the wind load. Therefore, in the airflow dynamics and simulation of wind loads before establishing an accurate wind speed model is crucial. At present, the application for wind turbines COMSOL fan, fan blades and wind load simulation field, the extremely important wind speed model is not perfect, most of the research is confined to a single constant wind speed, wind speed virtually ignored the magnitude and direction of change, on changes over time and space at the same time is one of the few studies of wind, so find a way to accurately describe the range of wind speeds, and can be combined well with COMSOL method can greatly improve the aerodynamic performance of wind turbines the overall level of .

scholarly journals Analysis of the Patent of a Protective Cover for Vertical-Axis Wind Turbines (VAWTs): Simulations of Wind Flow

2020 ◽  
Vol 12 (18) ◽  
pp. 7818
Author(s):  
Jose Alberto Moleón Baca ◽  
Antonio Jesús Expósito González ◽  
Candido Gutiérrez Montes
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Turbines ◽  
High Speed ◽  
Experimental Tests ◽  
Weather Conditions ◽  
Vertical Axis ◽  
Good Alternative ◽  
Wind Speeds ◽  
Vertical Axis Wind Turbines

This paper presents a numerical and experimental analysis of the patent of a device to be used in vertical-axis wind turbines (VAWTs) under extreme wind conditions. The device consists of two hemispheres interconnected by a set of conveniently implemented variable section ducts through which the wind circulates to the blades. Furthermore, the design of the cross-section of the ducts allows the control of the wind speed inside the device. These ducts are intended to work as diffusers or nozzles, depending on the needs of the installation site. Simulations were performed for the case of high-speed external wind, for which the ducts act as diffusers to reduce wind speed and maintain a well-functioning internal turbine. Four different patent designs were analyzed, focusing on turbine performance and generated power. The results indicate that the patent allows the generation of electric power for a greater range of wind speeds than with a normal wind turbine. The results support that this patent may be a good alternative for wind power generation in geographic areas with extreme weather conditions or with maintained or strong gusty wind. Experimental tests were carried out on the movement of the blades using the available model. Finally, the power curve of the model of this wind turbine was obtained.

scholarly journals Results from a wake-steering experiment at a commercial wind plant: investigating the wind speed dependence of wake-steering performance

2021 ◽  
Vol 6 (6) ◽  
pp. 1427-1453
Author(s):  
Eric Simley ◽  
Paul Fleming ◽  
Nicolas Girard ◽  
Lucas Alloin ◽  
Emma Godefroy ◽  
...  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Wind Direction ◽  
Wind Farm ◽  
Poor Performance ◽  
Power Production ◽  
Wind Rose ◽  
Wind Speeds ◽  
Variability Model

Abstract. Wake steering is a wind farm control strategy in which upstream wind turbines are misaligned with the wind to redirect their wakes away from downstream turbines, thereby increasing the net wind plant power production and reducing fatigue loads generated by wake turbulence. In this paper, we present results from a wake-steering experiment at a commercial wind plant involving two wind turbines spaced 3.7 rotor diameters apart. During the 3-month experiment period, we estimate that wake steering reduced wake losses by 5.6 % for the wind direction sector investigated. After applying a long-term correction based on the site wind rose, the reduction in wake losses increases to 9.3 %. As a function of wind speed, we find large energy improvements near cut-in wind speed, where wake steering can prevent the downstream wind turbine from shutting down. Yet for wind speeds between 6–8 m/s, we observe little change in performance with wake steering. However, wake steering was found to improve energy production significantly for below-rated wind speeds from 8–12 m/s. By measuring the relationship between yaw misalignment and power production using a nacelle lidar, we attribute much of the improvement in wake-steering performance at higher wind speeds to a significant reduction in the power loss of the upstream turbine as wind speed increases. Additionally, we find higher wind direction variability at lower wind speeds, which contributes to poor performance in the 6–8 m/s wind speed bin because of slow yaw controller dynamics. Further, we compare the measured performance of wake steering to predictions using the FLORIS (FLOw Redirection and Induction in Steady State) wind farm control tool coupled with a wind direction variability model. Although the achieved yaw offsets at the upstream wind turbine fall short of the intended yaw offsets, we find that they are predicted well by the wind direction variability model. When incorporating the expected yaw offsets, estimates of the energy improvement from wake steering using FLORIS closely match the experimental results.

scholarly journals Results from a Wake Steering Experiment at a Commercial Wind Plant: Investigating the Wind Speed Dependence of Wake Steering Performance

2021 ◽  
Author(s):  
Eric Simley ◽  
Paul Fleming ◽  
Nicolas Girard ◽  
Lucas Alloin ◽  
Emma Godefroy ◽  
...  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Wind Direction ◽  
Wind Farm ◽  
Poor Performance ◽  
Power Production ◽  
Wind Rose ◽  
Wind Speeds ◽  
Variability Model

Abstract. Wake steering is a wind farm control strategy in which upstream wind turbines are misaligned with the wind to redirect their wakes away from downstream turbines, thereby increasing the net wind plant power production and reducing fatigue loads generated by wake turbulence. In this paper, we present results from a wake steering experiment at a commercial wind plant involving two wind turbines spaced 3.7 rotor diameters apart. During the three-month experiment period, we estimate that wake steering reduced wake losses by 5.7 % for the wind direction sector investigated. After applying a long-term correction based on the site wind rose, the reduction in wake losses increases to 9.8 %. As a function of wind speed, we find large energy improvements near cut-in wind speed, where wake steering can prevent the downstream wind turbine from shutting down. Yet for wind speeds between 6–8 m/s, we observe little change in performance with wake steering. However, wake steering was found to improve energy production significantly for below-rated wind speeds from 8–12 m/s. By measuring the relationship between yaw misalignment and power production using a nacelle lidar, we attribute much of the improvement in wake steering performance at higher wind speeds to a significant reduction in the power loss of the upstream turbine as wind speed increases. Additionally, we find higher wind direction variability at lower wind speeds, which contributes to poor performance in the 6–8 m/s wind speed bin because of slow yaw controller dynamics. Further, we compare the measured performance of wake steering to predictions using the FLORIS (FLOw Redirection and Induction in Steady State) wind farm control tool coupled with a wind direction variability model. Although the achieved yaw offsets at the upstream wind turbine fall short of the intended yaw offsets, we find that they are predicted well by the wind direction variability model. When incorporating the predicted achieved yaw offsets, estimates of the energy improvement from wake steering using FLORIS closely match the experimental results.

Comparison of Various Blade Profiles in a Two-Blade Conventional Savonius Wind Turbine

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Rahim Hassanzadeh ◽  
Milad Mohammadnejad ◽  
Sajad Mostafavi
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Power Output ◽  
Urban Areas ◽  
Cost Effective ◽  
Maximum Power ◽  
Power Coefficient ◽  
Total Power ◽  
Wind Speeds ◽  
Savonius Wind Turbine

Abstract Savonius turbines are one of the old and cost-effective turbines which extract the wind energy by the drag force. Nowadays, they use in urban areas to generate electricity due to their simple structure, ease of maintenance, and acceptable power output under a low wind speed. However, their efficiency is low and the improvement of their performance is necessary to increase the total power output. This paper compares four various blade profiles in a two-blade conventional Savonius wind turbine. The ratios of blade diameter to the blade depth of s/d = 0.3, 0.5, 0.7, and 1 are tested under different free-wind speeds of 3, 5, and 7 m/s and tip speed ratios (TSRs) in the range from 0.2 to 1.2. It is found that the profile of blades in a Savonius rotor plays a considerable role in power characteristics. Also, regardless of blades profile and free-wind speed, the maximum power coefficient develops in TSR = 0.8. In addition, increasing the free-wind speed enhances the rotor performance of all cases under consideration. Finally, it is revealed that the rotor with s/d = 0.5 provides maximum power coefficients in all free-wind speeds and TSR values among the rotors under consideration, whereas the rotor with s/d = 1 is the worth cases.

Sign in / Sign up

Export Citation Format

Share Document