scholarly journals A novel self-powered supply for GCT gate drivers

2021 ◽  
Author(s):  
Weiqian Hu
Keyword(s):  
High Voltage ◽  
Power Converters ◽  
Power Supplies ◽  
Voltage Level ◽  
Snubber Circuit ◽  
Gate Driver ◽  
Self Powered ◽  
Isolation Transformer ◽  
Laboratory Prototype ◽  
Gate Drivers

This thesis is devoted to the development of a novel self-powered supply (SPS) for the gate driver of integrated Gate Commutated Thyristors (GCT). In commercial GCT power supplies, a high-voltage isolation transformer is an indispensable device. Since the GCT devices are normally for high-power converters operating at a voltage level of 2.3KV to 13.8KV, the high-voltage isolation transformer is expensive in cost and bulky in size. The SPS proposed in this thesis transfers energy from GCT snubber circuits and generates a regulated dc supply for the GCT gate driver. Since the snubber circuit is at the same potential as the GCT device, the insulation level of the self-powered supply is reduced from a few thousand volts to a couple of hundred volts, leading to a significant reduction in cost and size. In this thesis, the configuration of the proposed SPS is presented, and its operating principle is elaborated. The strategy for maximizing the SPS output power is analyzed. It is demonstrated that SPS can provide a regulated output up to 60W for most commercial GCT gate drivers. The performance of the SPS is verified by experiments on a 60W laboratory prototype.

scholarly journals A novel self-powered supply for GCT gate drivers

2021 ◽  
Author(s):  
Weiqian Hu
Keyword(s):  
High Voltage ◽  
Power Converters ◽  
Power Supplies ◽  
Voltage Level ◽  
Snubber Circuit ◽  
Gate Driver ◽  
Self Powered ◽  
Isolation Transformer ◽  
Laboratory Prototype ◽  
Gate Drivers

This thesis is devoted to the development of a novel self-powered supply (SPS) for the gate driver of integrated Gate Commutated Thyristors (GCT). In commercial GCT power supplies, a high-voltage isolation transformer is an indispensable device. Since the GCT devices are normally for high-power converters operating at a voltage level of 2.3KV to 13.8KV, the high-voltage isolation transformer is expensive in cost and bulky in size. The SPS proposed in this thesis transfers energy from GCT snubber circuits and generates a regulated dc supply for the GCT gate driver. Since the snubber circuit is at the same potential as the GCT device, the insulation level of the self-powered supply is reduced from a few thousand volts to a couple of hundred volts, leading to a significant reduction in cost and size. In this thesis, the configuration of the proposed SPS is presented, and its operating principle is elaborated. The strategy for maximizing the SPS output power is analyzed. It is demonstrated that SPS can provide a regulated output up to 60W for most commercial GCT gate drivers. The performance of the SPS is verified by experiments on a 60W laboratory prototype.

scholarly journals A special high-frequency soft-switched DC/DC power supply for GCT gate driver

2021 ◽  
Author(s):  
Jahangir Afsharian
Keyword(s):  
Power Supply ◽  
High Frequency ◽  
Optimization Procedure ◽  
Power Supplies ◽  
Zero Voltage Switching ◽  
General Power ◽  
Gate Driver ◽  
Isolation Transformer ◽  
Experimental Use ◽  
Gate Drivers

This thesis is devoted to the development of a novel parallel isolated power supply (PIPS) for the gate driver of integrated Gate Commutated Thyristors (GCT). The proposed PIPS is essentially a special high frequency soft switched DC/DC converter, integrating six parallel isolated power supplies in one module where each power supply generates a regulated dc supply for the GCT gate driver. In commercial GCT power supplies, a high-voltage isolation transformer is indispensable but highly inefficient in terms of cost and size, which can be significantly improved by the optimized transformer. In all, this design strives to achieve a general power supply for powering up the gate drivers of all types of GCT devices in all MV applications with minimal changes in configuration. In this thesis, the configuration of PIPS is presented and its operating principle is elaborated. The transformer optimization procedure satisfying the voltage isolation requirement of GCT gate drivers is extensively discussed. The performance of PIPS, including the front end DC/DC converter, zero voltage switching phase-shift full bridge (ZVS-PS-FB) converter, and the optimization of the transformer, is verified by simulations and experiments where a 360W laboratory prototype is built for the experimental use.

scholarly journals A special high-frequency soft-switched DC/DC power supply for GCT gate driver

2021 ◽  
Author(s):  
Jahangir Afsharian
Keyword(s):  
Power Supply ◽  
High Frequency ◽  
Optimization Procedure ◽  
Power Supplies ◽  
Zero Voltage Switching ◽  
General Power ◽  
Gate Driver ◽  
Isolation Transformer ◽  
Experimental Use ◽  
Gate Drivers

This thesis is devoted to the development of a novel parallel isolated power supply (PIPS) for the gate driver of integrated Gate Commutated Thyristors (GCT). The proposed PIPS is essentially a special high frequency soft switched DC/DC converter, integrating six parallel isolated power supplies in one module where each power supply generates a regulated dc supply for the GCT gate driver. In commercial GCT power supplies, a high-voltage isolation transformer is indispensable but highly inefficient in terms of cost and size, which can be significantly improved by the optimized transformer. In all, this design strives to achieve a general power supply for powering up the gate drivers of all types of GCT devices in all MV applications with minimal changes in configuration. In this thesis, the configuration of PIPS is presented and its operating principle is elaborated. The transformer optimization procedure satisfying the voltage isolation requirement of GCT gate drivers is extensively discussed. The performance of PIPS, including the front end DC/DC converter, zero voltage switching phase-shift full bridge (ZVS-PS-FB) converter, and the optimization of the transformer, is verified by simulations and experiments where a 360W laboratory prototype is built for the experimental use.

A High-Voltage Terminal for a Field-Emission Gun

1972 ◽  
Vol 30 ◽  
pp. 428-429
Author(s):  
N. F. Ziegler
Keyword(s):  
Field Emission ◽  
High Voltage ◽  
Atmospheric Pressure ◽  
Power Supplies ◽  
High Coherence

A high-voltage terminal has been constructed for housing the various power supplies and metering circuits required by the field-emission gun (described elsewhere in these Proceedings) for the high-coherence microscope. The terminal is cylindrical in shape having a diameter of 14 inches and a length of 24 inches. It is completely enclosed by an aluminum housing filled with Freon-12 gas at essentially atmospheric pressure. The potential of the terminal relative to ground is, of course, equal to the accelerating potential of the microscope, which in the present case, is 150 kilovolts maximum.

Development of a Base Element and Its Use in Topologies of High-Voltage Power Converters

Vestnik MEI ◽  
2018 ◽  
Vol 5 (5) ◽  
pp. 48-57
Author(s):  
Pavel A. Voronin ◽  
◽  
Igor Р. Voronin ◽  
Elena M. Dukhnich ◽  
◽  
...  
Keyword(s):  
High Voltage ◽  
Power Converters ◽  
Base Element

Analysis and Design of 3.3 kV IGBT Based Three-Level DC/DC Converter with High-Frequency Isolation and Current Doubler Rectifier

2009 ◽  
Vol 25 (25) ◽  
pp. 103-108
Author(s):  
Dmitri Vinnikov ◽  
Tanel Jalakas ◽  
Indrek Roasto
Keyword(s):  
High Voltage ◽  
High Frequency ◽  
Power Converter ◽  
Rolling Stock ◽  
Analysis And Design ◽  
Auxiliary Power ◽  
Igbt Modules ◽  
Isolation Transformer ◽  
New Generation ◽  
Generation Power

Analysis and Design of 3.3 kV IGBT Based Three-Level DC/DC Converter with High-Frequency Isolation and Current Doubler RectifierThe paper presents the findings of a R&D project connected to the development of auxiliary power supply (APS) for the high-voltage DC-fed rolling stock applications. The aim was to design a new-generation power converter utilizing high-voltage IGBT modules, which can outpace the predecessors in terms of power density, i.e. to provide more power for smaller volumetric space. The topology proposed is 3.3 kV IGBT-based three-level neutral point clamped (NPC) half-bridge with high-frequency isolation transformer and current doubler rectifier that fulfils all the targets imposed by the designers. Despite an increased component count the proposed converter is very simple in design and operation. The paper provides an overview of the design with several recommendations and guidelines. Moreover, the simulation and experimental results are discussed and the performance evaluation of the proposed converter is presented.

scholarly journals High Power Density, High-Voltage Parallel Resonant Converter Using Parasitic Capacitance on the Secondary Side of a Transformer

Electronics ◽  
2021 ◽  
Vol 10 (14) ◽  
pp. 1736
Author(s):  
Jaean Kwon ◽  
Rae-Young Kim
Keyword(s):  
Power Density ◽  
High Voltage ◽  
Electrostatic Precipitator ◽  
Power Supplies ◽  
Equivalent Model ◽  
Resonant Converter ◽  
High Voltage Power Supply ◽  
Resonant Capacitor ◽  
Parasitic Components ◽  
Secondary Side

High-voltage DC power supplies are used in several applications, including X-ray, plasma, electrostatic precipitator, and capacitor charging. However, such a high-voltage power supply has problems, such as a decrease in reliability, owing to an increase in output ripple voltage, and a decrease in power density, owing to an increase in volume. Therefore, this study proposes a method for improving the power density of a parallel resonant converter using the parasitic capacitor of the secondary side of the transformer. Due to the fact that high-voltage power supplies have many turns on the secondary side, a significant number of parasitic capacitors are generated. In addition, in the case of a parallel resonant converter, because the transformer and the primary resonant capacitor are connected in parallel, the parasitic capacitor component generated on the secondary side of the transformer can be equalized and used. A parallel cap-less resonant converter structure developed using the parasitic components of such transformers is proposed. Primary side and secondary side equivalent model analyses are conducted in order to derive new equations and gain waveforms. Finally, the validity of the proposed structure is verified experimentally.

scholarly journals 2D Nanomaterials for Effective Energy Scavenging

2021 ◽  
Vol 13 (1) ◽  
Author(s):  
Md Al Mahadi Hasan ◽  
Yuanhao Wang ◽  
Chris R. Bowen ◽  
Ya Yang
Keyword(s):  
Large Scale ◽  
Waste Heat ◽  
Material Selection ◽  
Power Supplies ◽  
Small Scale ◽  
Energy Scavenging ◽  
Power Sources ◽  
Practical Applications ◽  
2D Nanomaterials ◽  
Self Powered

AbstractThe development of a nation is deeply related to its energy consumption. 2D nanomaterials have become a spotlight for energy harvesting applications from the small-scale of low-power electronics to a large-scale for industry-level applications, such as self-powered sensor devices, environmental monitoring, and large-scale power generation. Scientists from around the world are working to utilize their engrossing properties to overcome the challenges in material selection and fabrication technologies for compact energy scavenging devices to replace batteries and traditional power sources. In this review, the variety of techniques for scavenging energies from sustainable sources such as solar, air, waste heat, and surrounding mechanical forces are discussed that exploit the fascinating properties of 2D nanomaterials. In addition, practical applications of these fabricated power generating devices and their performance as an alternative to conventional power supplies are discussed with the future pertinence to solve the energy problems in various fields and applications.

Sign in / Sign up

Export Citation Format

Share Document