scholarly journals Analytical Estimation of the Residual Drift of Reinforced Concrete Columns under the Ultimate Displacement Capacity

2020 ◽  
Author(s):  
Sinan Cansız
Keyword(s):  
Reinforced Concrete ◽  
Axial Load ◽  
Concrete Columns ◽  
Load Level ◽  
Transverse Reinforcement ◽  
Longitudinal Reinforcement ◽  
Reinforced Concrete Columns ◽  
Residual Drift ◽  
Drift Ratio ◽  
Ultimate Displacement

Reinforced concrete columns are the most important structural elements that determine the ductility of the structures. The main parameters affecting the behavior of reinforced concrete columns are axial load level, shear span, percent of longitudinal reinforcement and percent of transverse reinforcement. The aim of this study is to examine residual damage behavior of RC columns under cyclic loading similar to the earthquake loads combined depend on variable axial load level, spanning to depth ratio, longitudinal reinforcement ratio and transverse reinforcement ratio. When the results of experiments are examined, it can be seen that the residual drift ratio of reinforced concrete columns can be used to characterize the damage occurred in the structure after earthquake or loading. In addition, the performance level of the reinforced concrete columns according to the residual drift ratio is defined in FEMA356. As a result of this study, the analytical equation that calculates the residual drift ratio of the reinforced concrete columns at the ultimate displacement limit is proposed.

scholarly journals Gravity Load Collapse Behavior of Nonengineered Reinforced Concrete Columns

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Chichaya Boonmee ◽  
Kittipoom Rodsin ◽  
Krissachai Sriboonma
Keyword(s):  
Reinforced Concrete ◽  
Cyclic Loading ◽  
Axial Load ◽  
Concrete Columns ◽  
Poor Quality ◽  
Load Level ◽  
Longitudinal Reinforcement ◽  
Reinforced Concrete Columns ◽  
Gravity Load ◽  
Collapse Behavior

This paper aims at investigating gravity load collapse behavior of extremely poor quality reinforced concrete columns under cyclic loading. Such columns were usually constructed by local people and may not be designed to meet any of the standards. It was found that their concrete strength may be as low as 5 MPa and the amount of longitudinal reinforcement may be lower than 1%. This type of column is deliberately defined as “nonengineered reinforced concrete column,” or NRCC. During earthquake, the gravity load collapse of the NRCC columns caused a large number of death tolls around the world. In this study, four columns as representative of existing NRCC were tested under cyclic loading. The compressive strength of concrete in order of 5 MPa was used to be representative of columns with poor quality concrete. Two axial load levels of 6 and 18 tons were used to study the influence of axial load level on maximum drift at gravity load collapse. To investigate the effect of bar types on drift capacity, 9 mm round bars were used in two specimens and 12 mm deformed bars were used for the rest of the specimens. The maximum drift before gravity load collapse was very dependent on the axial load level. The maximum drift of the specimens subjected to high axial load (18 tons) was extremely low at approximately 1.75% drifts. The use of deformed bars (associated with larger amount of longitudinal reinforcement) caused the damage to severely dissipate all over the height of the columns. Such damage caused columns to collapse at a lower drift compared to those using round bars. Finally, the plastic hinge model was used to predict the maximum drift of the low strength columns. It was found that the model overly underestimates the drift at gravity load collapse.

SEISMIC PERFORMANCE OF GFRP-RC RECTANGULAR COLUMNS: NUMERICAL STUDY

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Ehab El-Salakawy ◽  
Fangxin Ye ◽  
Yasser Mostafa Selmy
Keyword(s):  
Reinforced Concrete ◽  
Cyclic Loading ◽  
Axial Load ◽  
Numerical Study ◽  
Concrete Strength ◽  
Weight Ratio ◽  
Concrete Columns ◽  
Load Level ◽  
Reinforced Concrete Columns ◽  
Rectangular Columns

Composite materials like glass fiber-reinforced polymer (GFRP) is becoming widely acceptable to be used as a reinforcing material due to its high ultimate tensile strength-to-weight ratio and excellent resistance to corrosion. However, the seismic behavior of GFRP-reinforced concrete columns has not been fully investigated yet. This paper presents the results of a numerical analysis of full-size GFRP-RC rectangular columns under cyclic loading. The simulated column depicts the lower part of a building column between the foundation and the point of contra-flexure at the mid-height of the column. GFRP reinforcement properties and concrete modeling based on fracture energy have been incorporated in the numerical model. Experimental validation has been used to examine the accuracy of the constructed finite element models (FEMs) using a commercially available software. The validated FEM was used to perform a parametric study, considering several concrete strength values and axial load levels, to study its influence on the performance of the GFRP-reinforced concrete columns under cyclic loading. It was concluded that the hysteretic dissipation capacity deteriorates under high axial load level due to severe softening of the concrete. The FE results showed a substantial improvement of the lateral load-carrying capacities by increasing concrete compressive strength.

scholarly journals Investigation of Parameters Affecting the Equivalent Yield Curvature of Reinforced Concrete Columns

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1594
Author(s):  
Umut Hasgul
Keyword(s):  
Reinforced Concrete ◽  
Cross Section ◽  
Axial Load ◽  
Concrete Columns ◽  
Load Level ◽  
Combined Effects ◽  
Reinforced Concrete Columns ◽  
Independent Effects ◽  
Equivalent Yield ◽  
Section Dimension

In this study, the response quantities affecting the equivalent yield curvature, which is important in the deformation-based seismic design and assessment of structural systems, are investigated for reinforced concrete columns with a square cross-section. In this context, the equivalent yield curvatures were determined by conducting moment–curvature analyses on various column models, in which the axial load level, cross-section dimension, longitudinal reinforcement ratio, and concrete compression strength were changed parametrically, and the independent and/or combined effects of the relevant parameters were discussed. Depending on the axial load levels of P/Agfc′ < 0.3, P/Agfc′ = 0.3, and P/Agfc′ > 0.3 for the considered columns, the yielding of reinforcement, yielding of reinforcement and/or concrete crushing, and concrete crushing governed the yield conditions, respectively. It can be noted that the cross-section dimension and axial load level became the primary parameters. Even though the independent effects with regard to particular parameters remained at minimal levels, the combined effects of them with the axial load became important in terms of the equivalent yield curvature.

scholarly journals The use of Grade 380 steel for transverse confining reinforcement in columns

1987 ◽  
Vol 20 (2) ◽  
pp. 99-115
Author(s):  
F. A. Zahn ◽  
R. Park ◽  
M. J. N. Priestley
Keyword(s):  
Reinforced Concrete ◽  
Axial Load ◽  
Analytical Study ◽  
Concrete Columns ◽  
Lateral Loading ◽  
Transverse Reinforcement ◽  
Reinforced Concrete Columns ◽  
Ductility Factor ◽  
Strain Behaviour ◽  
Curvature Ductility

The results of recent experimental and analytical studies of the stress-strain behaviour of concrete confined by New Zealand manufactured Grade 275 or Grade 380 reinforcing steel are presented. First, the behaviour of three pairs of concentrically loaded reinforced concrete columns containing spirals from either Grade
275 or Grade 380 steel are compared, including the stage at which spiral fracture occurred. Second, the results of tests on four reinforced concrete columns containing Grade 380 spiral or rectangular hoop reinforcement and subjected to combined axial
load and cyclic lateral loading are reported. An analytical
study which was conducted to determine the available curvature ductility factor at the stage of fracture of the transverse reinforcement is described. The results are used to give a guideline for the safe use of Grade 380 steel as transverse confining reinforcement.

scholarly journals Shear Strength Model for Reinforced Concrete Columns with Low Transverse Reinforcement Ratios

2014 ◽  
Vol 17 (10) ◽  
pp. 1373-1385 ◽  
Author(s):  
Cao Thanh Ngoc Tran ◽  
Bing Li
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Axial Load ◽  
Concrete Columns ◽  
Transverse Reinforcement ◽  
Reinforced Concrete Column ◽  
Reinforced Concrete Columns ◽  
Existing Structures ◽  
Reversed Cyclic ◽  
Constant Axial Load

This paper introduces an equation developed based on the strut-and-tie analogy to predict the shear strength of reinforced concrete columns with low transverse reinforcement ratios. The validity and applicability of the proposed equation are evaluated by comparison with available experimental data. The proposed equation includes the contributions from concrete and transverse reinforcement through the truss action, and axial load through the strut action. A reinforced concrete column with a low transverse reinforcement ratio, commonly found in existing structures in Singapore and other parts of the world was tested to validate the assumptions made during the development of the proposed equation. The column specimen was tested to failure under the combination of a constant axial load of 0.30 f' c A g and quasi-static cyclic loadings to simulate earthquake actions. The analytical results revealed that the proposed equation is capable of predicting the shear strength of reinforced concrete columns with low transverse reinforcement ratios subjected to reversed cyclic loadings to a satisfactory level of accuracy

scholarly journals Behavior of Square RC Short Columns with New Arrangement of Ties Subjected to Axial Load: Experimental and Numerical Studies

2022 ◽  
Author(s):  
Hazem Elbakry ◽  
Tarek Ebeido ◽  
El-Tony M. El-Tony ◽  
Momen Ali
Keyword(s):  
Reinforced Concrete ◽  
Axial Load ◽  
Concrete Columns ◽  
Experimental Program ◽  
Transverse Reinforcement ◽  
Reinforcing Bars ◽  
Rc Columns ◽  
Reinforced Concrete Columns ◽  
Short Columns ◽  
Numerical Studies

Reinforced concrete columns consume large quantities of ties, especially inner cross-ties in columns with large dimensions. In some cases, nesting of the pillars occurs as a result of the presence of cross-ties. The main objective of this paper is to develop new methods for transverse reinforcement in RC columns and investigate their effect on the behavior of the columns. The proposed V-ties as transverse reinforcement replacing the ordinary and cross-ties details are economically feasible. They facilitate shorter construction periods and decrease materials and labor costs. For this purpose, experimental and numerical studies are carried out. In the experimental program, nine reinforced concrete columns with identical concrete dimensions and longitudinal reinforcing bars were prepared and tested under concentric axial load with different tie configurations. The main parameters were the tie configurations and the length (lv) of V-tie legs. As part of the numerical study, the finite element model using the ABAQUS software program obtained good agreement with the experimental results of specimens. A numerical parametric study was carried out to study the influence of concrete compressive strength and longitudinal reinforcement ratio on the behavior of RC columns with the considered tie configurations. Based on the experimental and numerical results, it was found that using V-tie techniques instead of traditional ties could increase the axial load capacity of columns, restrain early local buckling of the longitudinal reinforcing bars and improve the concrete core confinement of reinforced concrete columns.

scholarly journals Background to the Monolithicity Factors for the Assessment of Jacketed Reinforced Concrete Columns

Buildings ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 55
Author(s):  
Georgia E. Thermou ◽  
Andreas J. Kappos
Keyword(s):  
Reinforced Concrete ◽  
Cross Section ◽  
Axial Load ◽  
Concrete Columns ◽  
Eurocode 8 ◽  
Longitudinal Reinforcement ◽  
Reinforced Concrete Columns ◽  
The Core ◽  
Visible Effect ◽  
Cross Section Geometry

The paper presents the background to the expressions adopted in the new Eurocode 8—3 for jacketed reinforced concrete columns. These are based on the commonly adopted concept of monolithicity factors (ratios of resistance of the jacketed section to that of an identical monolithic one). These factors are derived here in two ways: (i) by fitting experimental results for jacketed columns and (ii) by an extended parametric study of substandard reinforced concrete (R/C) members that were retrofitted by adding R/C jackets, analysed using a model developed by the authors that takes into account slip at the interface. Apart from the cross-section geometry and the thickness of the jacket, parameters of the investigation were the material properties of the core cross-section and the jacket, as well as the percentage of longitudinal reinforcement of the jacket and the percentage of dowels placed to connect the existing member to the jacket. It was found that the parameter that had the most visible effect on these factors was the normalised axial load (ν). The finally adopted factors are either simple functions of ν or constant values.

Sign in / Sign up

Export Citation Format

Share Document