scholarly journals Calculation of the Effective Thermal Cross-section and Its Temperature Coefficient, (I)

Author(s):  
Akinao SHIMIZU
2019 ◽  
Vol 55 (5) ◽  
Author(s):  
J. Lerendegui-Marco ◽  
C. Guerrero ◽  
T. Belgya ◽  
B. Maróti ◽  
K. Eberhardt ◽  
...  

2019 ◽  
Vol 2019 (9) ◽  
Author(s):  
R Kitahara ◽  
K Hirota ◽  
S Ieki ◽  
T Ino ◽  
Y Iwashita ◽  
...  

Abstract In a neutron lifetime measurement at the Japan Proton Accelerator Complex, the neutron lifetime is calculated from the neutron decay rate and the incident neutron flux. The flux is obtained by counting the protons emitted from the neutron absorption reaction of ${}^{3}{\rm He}$ gas, which is diluted in a mixture of working gas in a detector. Hence, it is crucial to determine the amount of ${}^{3}{\rm He}$ in the mixture. In order to improve the accuracy of the number density of the ${}^{3}{\rm He}$ nuclei, we have suggested using the ${}^{14}{\rm N}({\rm n},{\rm p}){}^{14}{\rm C}$ reaction as a reference because this reaction involves similar kinetic energy to the $^3$He(n,p)$^3$H reaction and a smaller reaction cross section to introduce reasonable large partial pressure. The uncertainty of the recommended value of the cross section, however, is not satisfied with our requirement. In this paper we report the most accurate experimental value of the cross section of the $^{14}$N(n,p)$^{14}$C reaction at a neutron velocity of 2200 m s$^{-1}$, measured relative to the $^3$He(n,p)$^3$H reaction. The result was 1.868 $\pm$ 0.003 (stat.) $\pm$ 0.006 (sys.) b. Additionally, the cross section of the $^{17}$O(n,$\alpha$)$^{14}$C reaction at the neutron velocity is also redetermined as 249 $\pm$ 6 mb.


1986 ◽  
Vol 29 (11) ◽  
pp. 1195-1203 ◽  
Author(s):  
J.R. Morante ◽  
A. Herms ◽  
J. Samitier ◽  
A. Cornet ◽  
E. Lora-Tamayo

1961 ◽  
Vol 39 (8) ◽  
pp. 1184-1192 ◽  
Author(s):  
W. H. Walker ◽  
R. E. Green

Cadmium ratio measurements have been made in similar lattice positions in ZEEP with thin foils of Sm152 and gold. From a comparison of these cadmium ratios we find[Formula: see text]If gσ0 is assumed to be 212 ± 12 barns, then I′ = 3100 ± 200 barns. On the assumption that only one resonance in Sm152, at 8 ev, contributes appreciably to both the resonance integral and the thermal cross section, it follows that g = 1 and that Γ, the width at half-maximum of the total cross section resonance, is 193 ± 5 milli-ev. Because of the appreciable disagreement between this value and one reported earlier, a new time-of-flight measurement of the resonance parameters has been made, and it is reported in the next paper (Chrien 1961).


2019 ◽  
Vol 55 (11) ◽  
Author(s):  
T. Wright ◽  
S. Bennett ◽  
S. Heinitz ◽  
U. Köster ◽  
R. Mills ◽  
...  

Abstract.Ampoules of amorphous 99.5% enriched 13C were irradiated at the PF1b neutron beam line at the high-flux ILL research reactor in order to produce 14C atoms. The precise ratio of 14C/13C was subsequently measured at the VERA Accelerator Mass Spectrometer, allowing the 13C(n,$ \gamma$γ)14C thermal cross section to be accurately determined. This is the first measurement of this cross section at sub-eV energies via this technique and the result of $ 1.52 \pm 0.07$1.52±0.07 mb for the thermal cross section is in good agreement with other recent measurements which were performed via Prompt Gamma-ray Activation Analysis.


1998 ◽  
Vol 518 ◽  
Author(s):  
Y. Yoshino

AbstractA transversal type 3.58MHz piezoelectric resonator has been fabricated using piezoelectric ZnO thin film on ELINVER (Fe-Ni-Cr-Ti ) alloy. The ZnO/ELINVER structure piezoelectric resonator has been designed to have 2 ppm temperature coefficient of frequency (TCF) per degree from -20 degrees to 80 degrees centigrade. The temperature coefficient of ELINVER alloy can be controlled to cancel the TCF of ZnO thin film by heat annealing. The ZnO thin film on ELINVER alloy shows c-axis orientation. The c-axis orientation of the ZnO thin film is strongly influenced by the surface roughness of the ELINVER alloy. The wet etching process has been adopted to shape the resonator made from ELINVER alloy substrate. The cross section of the resonator is a structure tapered about 10 degrees, created using different sized photo masks on each side of the ELINVER surface. The tapered cross section of the transversal type resonator greatly improves the frequency characteristics of the resonator. The electrical characteristics of the resonator after the improvement include a resonance frequency of 3.58MHz trimmed by a YAG laser, and resonance resistance of about 200 Ω. The temperature coefficient of frequency is about 1.5 ppm per degree at a temperature range of-20 degrees to 80 degrees centigrade.


Sign in / Sign up

Export Citation Format

Share Document