scholarly journals Heat Transfer in a Square Porous Cavity With Partial Heating and Cooling for Opposite Vertical Walls

2011 ◽  
Vol 19 (5) ◽  
pp. 107-121
Author(s):  
Muyassar E. Ismaeel
Keyword(s):  
Heat Transfer ◽  
Porous Cavity ◽  
Heating And Cooling ◽  
Partial Heating ◽  
Vertical Walls

Investigation of heat transfer in irregular porous cavity subjected to various boundary conditions

2019 ◽  
Vol 29 (1) ◽  
pp. 418-447 ◽  
Author(s):  
Irfan Anjum Badruddin
Keyword(s):  
Heat Transfer ◽  
Boundary Conditions ◽  
Outer Boundary ◽  
Governing Equations ◽  
Content Type ◽  
Porous Cavity ◽  
Various Boundary Conditions ◽  
Heating Source ◽  
Transfer Behavior ◽  
Vertical Walls

Purpose The purpose of this paper is to investigate the heat transfer in an arbitrary cavity filled with porous medium. The geometry of the cavity is such that an isothermal heating source is placed centrally at the bottom of the cavity. The height and width of the heating source is varied to analyses its effect on the heat transfer characteristics. The investigation is carried out for three different cases of outer boundary conditions such as two outside vertical walls being maintained at cold temperature To, two vertical and top horizontal surface being heated to. To and the third case with top surface kept at To but other surfaces being adiabatic. Design/methodology/approach Finite element method is used to solve the governing equations. Findings It is observed that the cavity exhibits unique heat transfer behavior as compared to regular cavity. The cases of boundary conditions are found to affect the heat transfer rate in the porous cavity. Originality/value This is original work representing the heat transfer in irregular porous cavity with various boundary conditions. This work is neither being published nor under review in any other journal.

Natural Convection From a Porous Cavity With Sublayers of Nonuniform Thickness: A Lumped System Analysis

2009 ◽  
Vol 132 (3) ◽  
Author(s):  
R. L. Marvel ◽  
F. C. Lai
Keyword(s):  
Heat Transfer ◽  
System Analysis ◽  
Numerical Study ◽  
Temperature Fields ◽  
Porous Cavity ◽  
Nonuniform Thickness ◽  
Sublayer Thickness ◽  
Vertical Walls ◽  
Quick Estimate ◽  
Rayleigh Numbers

A numerical study has been performed to further investigate the flow and temperature fields in layered porous cavity. The geometry considered is a two-dimensional square cavity comprising of three or four vertical sublayers with nonuniform thickness and distinct permeability. The cavity is subjected to differential heating from the vertical walls. The results obtained are used to further evaluate the capacity of the lumped-system analysis in the prediction of heat transfer results of layered porous cavities. It has been found that predictions by the lumped-system model are reasonably good for the range of Rayleigh numbers encountered in engineering applications. In addition, the predictions improve when the number of sublayers increases as well as the sublayer thickness becomes more uniform. Thus, it proves that the lumped-system analysis can offer a quick estimate of heat transfer result from a layered porous cavity with reasonable accuracy.

Natural Convection From a Layered Porous Cavity With Non-Uniform Sublayers

2007 ◽  
Author(s):  
R. L. Marvel ◽  
F. C. Lai
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
System Analysis ◽  
Numerical Study ◽  
Temperature Fields ◽  
Square Cavity ◽  
Porous Cavity ◽  
Differential Heating ◽  
Vertical Walls

A numerical study has been performed to further investigate the flow and temperature fields in layered porous cavity. The geometry considered is a square cavity with 3 or 4 non-uniform sublayers and is subjected to differential heating from the vertical walls. The results obtained are used to further evaluate the feasibility of using the lumped-system analysis for heat transfer in layered porous cavities as proposed in the previous study. To this end, the effective permeabilities based on the arithmetic and harmonic averaging schemes are examined for their use in the conjunction with the lumped-system analysis.

Buildings

2017 ◽  
Author(s):  
Peter Rez
Keyword(s):  
Heat Transfer ◽  
Heat Pump ◽  
Energy Efficient ◽  
Energy Use ◽  
Fossil Fuel ◽  
Local Climate ◽  
Heating And Cooling ◽  
The Difference ◽  
As If

Most of the energy used by buildings goes into heating and cooling. For small buildings, such as houses, heat transfer by conduction through the sides is as much as, if not greater than, the heat transfer from air exchanges with the outside. For large buildings, such as offices and factories, the greater volume-to-surface ratio means that air exchanges are more significant. Lights, people and equipment can make significant contributions. Since the energy used depends on the difference in temperature between the inside and the outside, local climate is the most important factor that determines energy use. If heating is required, it is usually more efficient to use a heat pump than to directly burn a fossil fuel. Using diffuse daylight is always more energy efficient than lighting up a room with artificial lights, although this will set a limit on the size of buildings.

scholarly journals Numerical Evaluation of a HVAC System Based on a High-Performance Heat Transfer Fluid

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3298
Author(s):  
Gianpiero Colangelo ◽  
Brenda Raho ◽  
Marco Milanese ◽  
Arturo de Risi
Keyword(s):  
Heat Transfer ◽  
High Performance ◽  
Cooling System ◽  
Electrical Energy ◽  
Simulation Software ◽  
Heat Transfer Fluid ◽  
Hvac System ◽  
Dynamic Simulations ◽  
Heating And Cooling ◽  
The University

Nanofluids have great potential to improve the heat transfer properties of liquids, as demonstrated by recent studies. This paper presents a novel idea of utilizing nanofluid. It analyzes the performance of a HVAC (Heating Ventilation Air Conditioning) system using a high-performance heat transfer fluid (water-glycol nanofluid with nanoparticles of Al2O3), in the university campus of Lecce, Italy. The work describes the dynamic model of the building and its heating and cooling system, realized through the simulation software TRNSYS 17. The use of heat transfer fluid inseminated by nanoparticles in a real HVAC system is an innovative application that is difficult to find in the scientific literature so far. This work focuses on comparing the efficiency of the system working with a traditional water-glycol mixture with the same system that uses Al2O3-nanofluid. The results obtained by means of the dynamic simulations have confirmed what theoretically assumed, indicating the working conditions of the HVAC system that lead to lower operating costs and higher COP and EER, guaranteeing the optimal conditions of thermo-hygrometric comfort inside the building. Finally, the results showed that the use of a nanofluid based on water-glycol mixture and alumina increases the efficiency about 10% and at the same time reduces the electrical energy consumption of the HVAC system.

Sign in / Sign up

Export Citation Format

Share Document