scholarly journals Mechanical Properties of Concrete Pipes with Pre-Existing Cracks

2020 ◽  
Vol 10 (4) ◽  
pp. 1545
Author(s):  
Zongyuan Zhang ◽  
Hongyuan Fang ◽  
Bin Li ◽  
Fuming Wang
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Bearing Capacity ◽  
Three Dimensional ◽  
Compressive Load ◽  
Full Scale ◽  
Element Analysis ◽  
Concrete Pipes ◽  
Concrete Pipe ◽  
Full Scale Tests

Concrete pipes are the most widely used municipal drainage pipes in China. When concrete pipes fall into years of disrepair, numerous problems appear. As one of the most common problems of concrete pipes, cracks impact on the deterioration of mechanical properties of pipes, which cannot be ignored. In the current work, normal concrete pipes and those with pre-existing cracks are tested on a full scale under an external compressive load. The effects of the length, depth, and location of cracks on the bearing capacity and mechanical properties of the concrete pipes are quantitatively analyzed. Based on the full-scale tests, three-dimensional finite element models of normal and cracked concrete pipes are developed, and the measured results are compared with the data of the finite element analysis. It is clear that the test measurements are in good agreement with the simulation results; the bearing capacity of a concrete pipe is inversely proportional to the length and depth of the crack, and the maximum circumferential strain of the pipe occurs at the location of the crack. The strain of the concrete pipe also reveals three stages of elasticity, plasticity, and failure as the external load rises. Finally, when the load series reaches the limit of the failure load of the concrete pipe with pre-existing cracks, the pipe breaks along the crack position.

Analyses of Full-Scale Tank Car Shell Impact Tests

2007 ◽  
Author(s):  
Y. H. Tang ◽  
H. Yu ◽  
J. E. Gordon ◽  
M. Priante ◽  
D. Y. Jeong ◽  
...  
Keyword(s):  
Finite Element ◽  
Test Data ◽  
Three Dimensional ◽  
Full Scale ◽  
Collision Dynamics ◽  
Dynamics Modeling ◽  
Dynamics Model ◽  
Rigid Plastic ◽  
Element Analysis ◽  
Closed Form Solutions

This paper describes analyses of a railroad tank car impacted at its side by a ram car with a rigid punch. This generalized collision, referred to as a shell impact, is examined using nonlinear (i.e., elastic-plastic) finite element analysis (FEA) and three-dimensional (3-D) collision dynamics modeling. Moreover, the analysis results are compared to full-scale test data to validate the models. Commercial software packages are used to carry out the nonlinear FEA (ABAQUS and LS-DYNA) and the 3-D collision dynamics analysis (ADAMS). Model results from the two finite element codes are compared to verify the analysis methodology. Results from static, nonlinear FEA are compared to closed-form solutions based on rigid-plastic collapse for additional verification of the analysis. Results from dynamic, nonlinear FEA are compared to data obtained from full-scale tests to validate the analysis. The collision dynamics model is calibrated using test data. While the nonlinear FEA requires high computational times, the collision dynamics model calculates gross behavior of the colliding cars in times that are several orders of magnitude less than the FEA models.

Finite Element Analysis of Elliptical Chord

2013 ◽  
Vol 3 (4) ◽  
pp. 44-61
Author(s):  
K. S. Narayana ◽  
R. T. Naik ◽  
R. C. Mouli ◽  
L. V. V. Gopala Rao ◽  
R. T. Babu Naik
Keyword(s):  
Finite Element ◽  
Natural Frequencies ◽  
Three Dimensional ◽  
Compressive Load ◽  
Dynamic Strength ◽  
Element Analysis ◽  
T Joints ◽  
Shell Elements ◽  
Tubular Joints ◽  
Plane Bending

The work presents the Finite element study of the effect of elliptical chords on the static and dynamic strength of tubular T-joints using ANSYS. Two different geometry configurations of the T-joints have been used, namely Type-1 and Type-2. An elastic analysis has been considered. The Static loading conditions used are: axial load, compressive load, In-plane bending (IPB) and Out-plane bending (OPB). The natural frequencies analysis (dynamic loading condition) has also been carried out. The geometry configurations of the T-joints have been used, vertical tubes are called brace and horizontal tubes are called chords. The joint consists of brace joined perpendicular to the circular chord. In this case the ends of the chord are held fixed. The material used is mild steel. Using ANSYS, finite element modeling and analysis of T-joint has been done under the aforementioned loading cases. It is one of the most powerful methods in use but in many cases it is an expensive analysis especially due to elastic–plastic and creep problems. Usually, three dimensional solid elements or shell elements or the combination of two types of elements are used for generating the tubular joints mesh. In tubular joints, usually the fluid induced vibrations cause the joint to fail under resonance. Therefore the natural frequencies analysis is also an important issue here. Generally the empirical results are required as guide or comparison tool for finite element investigation. It is an effective way to obtain confidence in the results derived. Shell elements have been used to model the assembled geometry. Finite element ANSYS results have been validated with the LUSAS FEA and experimental results, that is within the experimentation error limit of ten percentage.

Three-dimensional finite element modelling of a full-scale geosynthetic-reinforced, pile-supported embankment

2015 ◽  
Vol 52 (12) ◽  
pp. 2041-2054 ◽  
Author(s):  
R. Kerry Rowe ◽  
K.-W. Liu
Keyword(s):  
Finite Element ◽  
Soft Soil ◽  
Three Dimensional ◽  
Single Layer ◽  
Full Scale ◽  
Numerical Results ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Pile Supported Embankment

The performance of four sections of a full-scale embankment constructed on soft soil is examined using a fully coupled and fully three-dimensional finite element analysis. The four sections had similar embankment loadings but different improvement options (one unimproved, one with pile-support only, one with a single layer geotextile-reinforced platform and pile-support, and one with two layers of geogrid-reinforced platform and pile-support). Like the field data, the numerical results show that the inclusion of piles decreases the settlement at the subsoil surface to 52% of that for the unimproved section, and the addition of a single layer of geotextile reinforcement (J = 800 kN/m) further reduced settlement to only 31% of that of the unimproved section. The effects of geosynthetic reinforcement and multiple layers of reinforcement on the performance of the pile-supported embankment are discussed. The relative load transfer is calculated using eight existing methods and they are compared with the field measurements and numerical results.

scholarly journals Finite Element Analysis and Full-Scale Testing of Locomotive Crashworthy Components

2013 ◽  
Author(s):  
Patricia Llana ◽  
Richard Stringfellow ◽  
Ronald Mayville
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
New Technologies ◽  
Element Model ◽  
Full Scale ◽  
Element Analysis ◽  
Design Concepts ◽  
Dynamic Finite Element Analysis ◽  
Full Scale Tests ◽  
Force Displacement

The Office of Research and Development of the Federal Railroad Administration (FRA) and the Volpe Center are continuing to evaluate new technologies for increasing the safety of passengers and operators in rail equipment. In recognition of the importance of override prevention in train-to-train collisions in which one of the vehicles is a locomotive, and in light of the success of crash energy management technologies in cab car-led passenger trains, the Volpe Center seeks to evaluate the effectiveness of components that could be integrated into the end structure of a locomotive that are specifically designed to mitigate the effects of a collision and, in particular, to prevent override of one of the lead vehicles onto the other. A research program has been conducted to develop, fabricate and test two crashworthy components for the forward end of a locomotive: (1) a deformable anti-climber, and (2) a push-back coupler. Detailed designs for these components were developed, and the performance of each design was evaluated through large deformation dynamic finite element analysis (FEA). Designs for two test articles that could be used to verify the performance of the component designs in full-scale tests were also developed. The two test articles were fabricated and dynamically tested by means of rail car impact in order to verify certain performance characteristics of the two components relative to specific requirements. The tests were successful in demonstrating the effectiveness of the two design concepts. Test results were consistent with finite element model predictions in terms of energy absorption capability, force-displacement behavior and modes of deformation.

Advances in the Railroad Locomotive Crashworthiness

2003 ◽  
Author(s):  
Swamidas Punwani ◽  
Gopal Samavedam ◽  
Steve Kokkins
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Impact Strength ◽  
Full Scale ◽  
Fuel Tank ◽  
Structural Components ◽  
Dynamic Impact ◽  
Element Analysis ◽  
Simulation Results ◽  
Full Scale Tests

The paper describes locomotive and fuel tank crashworthiness research being conducted by the Federal Railroad Administration for improved safety of the locomotive crew under collision scenarios. The research involves static and dynamic impact strength evaluations of locomotive structural components. These evaluations which are based on full scale tests and simulations using finite element analysis are described in this paper. Correlations between the test and simulation results are also presented in some cases.

scholarly journals Experimental and Numerical Analysis of The Used Hollow Slab

2018 ◽  
Vol 175 ◽  
pp. 01036
Author(s):  
Xudong Hua ◽  
Xingwei Xue ◽  
Junlong Zhou ◽  
Hai Zhang
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Three Dimensional ◽  
Reinforced Concrete Structure ◽  
Analysis Model ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Long Time ◽  
Bending Capacity ◽  
Three Dimensional Finite Element

The actual bearing capacity of a bridge in active service is crucial to the structure, but such data is generally difficult to obtain. In order to obtain the actual ultimate bending capacity of the used hollow slab, a destructive test of a hollow slab, which has been used ten years, has been carried out. Moreover, based on the experimental analysis of the material parameter data, a three-dimensional finite element nonlinear analysis model of the used hollow slab was established. Through the experiment and finite element analysis of the used hollow slab, the comparisons of the failure mode, crack propagating and ultimate bending capacity were focused on. The main conclusions obtained through the study are as follows: (1) Strand is a kind of stable prestressed material, which can maintain good mechanical properties for a long time; (2) The used hollow slab still maintains good ultimate bending capacity, although underwent a decreased rigidity due to long-term cumulative damage; (3) The total strain fracture model is qualified for simulating the nonlinearity of concrete material, and can obtain the ultimate bearing capacity of reinforced concrete structure effectively as well as simulates the development of cracks well.

scholarly journals Simplified 2D Finite Element Model for Calculation of the Bearing Capacity of Eccentrically Compressed Concrete-Filled Steel Tubular Columns

2021 ◽  
Vol 11 (24) ◽  
pp. 11645
Author(s):  
Anton Chepurnenko ◽  
Batyr Yazyev ◽  
Besarion Meskhi ◽  
Alexey Beskopylny ◽  
Kazbek Khashkhozhev ◽  
...  
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Cross Sections ◽  
Three Dimensional ◽  
Element Model ◽  
Longitudinal Force ◽  
Effective Area ◽  
Element Analysis ◽  
Tubular Columns ◽  
Cfst Columns

Concrete-filled steel tubular (CFST) columns are widely used in construction due to effective resistance to compression and bending joint action. However, currently, there is no generally accepted effective calculation method considering both nonlinearities of the materials and lateral compression. The article proposes the finite element analysis method of concrete-filled steel tubular columns in a physically nonlinear formulation by reducing a three-dimensional problem to a two-dimensional one based on the hypothesis of plane sections. The equations of Geniev’s concrete theory of plasticity are used as relations establishing the relationship between stresses and strains. The technique was tested by comparing the solution with the calculation in a three-dimensional formulation in the LIRA-SAPR software package and with the experimental data of A.L. Krishan and A.I. Sagadatov. It has been established that the effective area of operation of circular-section columns are small eccentricities of the longitudinal force. The proposed approach can be applied to analyzing the stress–strain state and bearing capacity of pipe-concrete columns of arbitrary cross-sections. There are no restrictions on the composition of concrete, and the shell material can be steel and fiberglass.

Sign in / Sign up

Export Citation Format

Share Document