scholarly journals Positioning Evaluation of Single and Dual-Frequency Low-Cost GNSS Receivers Signals Using PPP and Static Relative Methods in Urban Areas

2021 ◽  
Vol 11 (22) ◽  
pp. 10642
Author(s):  
Rosendo Romero-Andrade ◽  
Manuel E. Trejo-Soto ◽  
Alejandro Vega-Ayala ◽  
Daniel Hernández-Andrade ◽  
Jesús R. Vázquez-Ontiveros ◽  
...  
Keyword(s):  
Urban Areas ◽  
Precise Point Positioning ◽  
Low Cost ◽  
Observation Data ◽  
Dual Frequency ◽  
Positional Accuracy ◽  
Gnss Receivers ◽  
Point Positioning ◽  
Error Circle ◽  
Vertical Positioning

A positional accuracy obtained by the Precise Point Positioning and static relative methods was compared and analyzed. Test data was collected using low-cost GNSS receivers of single- and dual-frequency in urban areas. The data was analyzed for quality using the TEQC program to determine the degree of affectation of the signal in the urban area. Low-cost GNSS receivers were found to be sensitive to the multipath effect, which impacts positioning. The horizontal and vertical accuracy was evaluated with respect to Mexican regulations for the GNSS establishment criteria. Probable Error Circle (CEP) and Vertical Positioning Accuracy (EPV) were performed on low cost GNSS receiver observation data. The results show that low-cost dual-frequency GNSS receivers can be used in urban areas. The precision was obtained in the order of 0.013 m in the static relative method. The results obtained are comparable to a geodetic receiver in a geodetic baseline of <20 km. The study does not recommend using single and dual frequencies low cost GNSS receivers based on results obtained by the Precise Point Positioning (PPP) method in urban areas. The inclusion of the GGM10 model reduces the vertical precision obtained by using low cost GNSS receivers in both methods, conforming to the regulations only in the horizontal component.

scholarly journals Sampling Rate Impact on Precise Point Positioning with a Low-Cost GNSS Receiver

2021 ◽  
Vol 11 (16) ◽  
pp. 7669
Author(s):  
Rosendo Romero-Andrade ◽  
Manuel E. Trejo-Soto ◽  
Jesús R. Vázquez-Ontiveros ◽  
Daniel Hernández-Andrade ◽  
Juan L. Cabanillas-Zavala
Keyword(s):  
Urban Areas ◽  
Precise Point Positioning ◽  
Low Cost ◽  
Sampling Rate ◽  
Static Mode ◽  
Gnss Receiver ◽  
High Sampling Rate ◽  
Gnss Receivers ◽  
Potential Alternative ◽  
Point Positioning

Nowadays, with the incursion of low-cost GNSS receivers with modern characteristics, it is common to investigate and apply new methodologies and solutions with different receivers of this nature. Based on this fact, the performance of the solution obtained from the low-cost GNSS receiver is evaluated compared to a geodetic grade GNSS receiver at different sampling frequencies for the PPP-static and PPP-kinematic modes. For this, the original RINEX observation files were analyzed and decimated into different sampling rates as 0.1, 0.2, 1, 5, 15 and 30 s with TEQC software. All RINEX files were submitted to the Canadian Spatial Reference System Precise Point Positioning (CSRS-PPP) online service for processing with static and kinematic modes. The PPP-derived coordinates from the low-cost GNSS receiver were compared with the geodetic receiver to evaluate the obtained solution. The results reveal that the behavior of all studied sampling rates from the low-cost GNSS receiver are constant in achieved positioning. In addition, the achieved precision shows that it is recommendable to use a high sampling rate to obtain a cm level in PPP-static mode by using a low-cost GNSS receiver, this mode being the most accurate and potential alternative for structural health monitoring studies, mapping and positioning in urban areas.

scholarly journals Real-time GNSS precise point positioning for low-cost smart devices

GPS Solutions ◽  
2021 ◽  
Vol 25 (2) ◽  
Author(s):  
Liang Wang ◽  
Zishen Li ◽  
Ningbo Wang ◽  
Zhiyu Wang
Keyword(s):  
Carrier Phase ◽  
Measurement Errors ◽  
Precise Point Positioning ◽  
Low Cost ◽  
Smart Devices ◽  
Dual Frequency ◽  
Static Mode ◽  
Phase Measurements ◽  
Positioning Errors ◽  
Point Positioning

AbstractGlobal Navigation Satellite System raw measurements from Android smart devices make accurate positioning possible with advanced techniques, e.g., precise point positioning (PPP). To achieve the sub-meter-level positioning accuracy with low-cost smart devices, the PPP algorithm developed for geodetic receivers is adapted and an approach named Smart-PPP is proposed in this contribution. In Smart-PPP, the uncombined PPP model is applied for the unified processing of single- and dual-frequency measurements from tracked satellites. The receiver clock terms are parameterized independently for the code and carrier phase measurements of each tracking signal for handling the inconsistency between the code and carrier phases measured by smart devices. The ionospheric pseudo-observations are adopted to provide absolute constraints on the estimation of slant ionospheric delays and to strengthen the uncombined PPP model. A modified stochastic model is employed to weight code and carrier phase measurements by considering the high correlation between the measurement errors and the signal strengths for smart devices. Additionally, an application software based on the Android platform is developed for realizing Smart-PPP in smart devices. The positioning performance of Smart-PPP is validated in both static and kinematic cases. Results show that the positioning errors of Smart-PPP solutions can converge to below 1.0 m within a few minutes in static mode and the converged solutions can achieve an accuracy of about 0.2 m of root mean square (RMS) both for the east, north and up components. For the kinematic test, the RMS values of Smart-PPP positioning errors are 0.65, 0.54 and 1.09 m in the east, north and up components, respectively. Static and kinematic tests both show that the Smart-PPP solutions outperform the internal results provided by the experimental smart devices.

Single-Frequency Precise Point Positioning Using Multi-Constellation GNSS: GPS, GLONASS, Galileo and BeiDou

GEOMATICA ◽  
2016 ◽  
Vol 70 (2) ◽  
pp. 113-122 ◽  
Author(s):  
Mahmoud Abd Rabbou ◽  
Ahmed El-Rabbany
Keyword(s):  
Urban Areas ◽  
Precise Point Positioning ◽  
Cost Effective ◽  
Convergence Time ◽  
Single Frequency ◽  
Dual Frequency ◽  
Positioning Accuracy ◽  
Point Positioning ◽  
Beidou Satellites ◽  
Gnss Observations

Single-frequency precise point positioning (PPP) presents a cost-effective positioning technique for a large number of users. However, it possesses low positioning accuracy and convergence time compared with the dual-frequency PPP. Single-frequency PPP commonly employs GPS satellite systems that suffer from poor satellite geometry, especially in dense urban areas. We develop a new single-frequency PPP model that combines the observations of current GNSS constellations, including GPS, GLONASS, Galileo and Beidou. The MGEX IGS final precise products are utilized to account for the orbital and clock errors, while the IGS final global ionospheric maps (GIM) model is used to correct for the ionospheric delay. The GNSS inter-system biases are treated as additional unknowns in the estimation process. The con tri bution of the additional GNSS observations to single-frequency PPP is assessed through solution comparison with its traditional GPS-only counterpart. Various GNSS combinations are considered in the assessment, including GPS/GLONASS, GPS/Galileo, GPS/BeiDou and all-constellation GNSS. It is shown that the additional GNSS observations enhance the PPP solution accuracy and convergence time in comparison with the tra di tional GPS-only solution. Except for stations with a sufficient number of tracked BeiDou satellites, both Galileo and BeiDou have marginal effects on the positioning accuracy due to their limited number of satel lites. However, for stations with a sufficient number of visible BeiDou satellites, an average of 40% PPP accuracy improvement is obtained. The major contribution to the PPP accuracy enhancement is obtained from GLONASS satellite observations.

Precise Point Positioning Model Using Triple GNSS Constellations: GPS, Galileo and BeiDou

2016 ◽  
Vol 10 (4) ◽  
Author(s):  
Akram Afifi ◽  
Ahmed El-Rabbany
Keyword(s):  
Real Time ◽  
Urban Areas ◽  
Precise Point Positioning ◽  
Convergence Time ◽  
Dual Frequency ◽  
Post Processing ◽  
International Gnss Service ◽  
Time Service ◽  
System Bias ◽  
Point Positioning

AbstractThis paper introduces a comparison between dual-frequency precise point positioning (PPP) post-processing model, which combines the observations of three different GNSS constellations, namely GPS, Galileo, and BeiDou and real-time PPP model. A drawback of a single GNSS system such as GPS, however, is the availability of sufficient number of visible satellites in urban areas. Combining GNSS observations offers more visible satellites to users, which in turn is expected to enhance the satellite geometry and the overall positioning solution. However, combining several GNSS observables introduces additional biases, which require rigorous modelling, including the GNSS time offsets and hardware delays. In this paper, a GNSS post-processing PPPP model is developed using ionosphere-free linear combination. The additional biases of the GPS, Galileo, and BeiDou combination are accounted for through the introduction of a new unknown parameter, which is identified as the inter-system bias, in the PPP mathematical model. Natural Resources Canada’s GPSPace PPP software is modified to enable a combined GPS / Galileo / BeiDou PPP solution and to handle the newly inter-system bias. A total of four data sets at four IGS stations are processed to verify the developed PPP model. Precise satellite orbit and clock products from the IGS-MGEX network are used to correct of the GPS, Galileo and BeiDou measurements. For the real-time PPP model the corrections of the satellites orbit and clock are obtained through the international GNSS service (IGS) real-time service (RTS). GPS and Galileo Observations are used for the GNSS RTS-IGS PPP model as the RTS-IGS satellite products are not available for BeiDou satellites. This paper provides the GNSS RTS-IGS PPP model using different satellite clock corrections namely: IGS01, IGC01, IGS01, and IGS03. All PPP models results of convergence time and positioning precision are compared to the traditional GPS-only PPP model. It is shown that combining GPS, Galileo, and BeiDou observations in a PPP model reduces the convergence time by 25 % compared with the GPS-only PPP model.

scholarly journals Enhanced model for precise point positioning with single and dual frequency GPS/Galileo observables

2014 ◽  
Vol XL-2 ◽  
pp. 173-177 ◽  
Author(s):  
A. Afifi ◽  
A. El-Rabbany
Keyword(s):  
Urban Areas ◽  
Precise Point Positioning ◽  
Convergence Time ◽  
Dual Frequency ◽  
Estimation Model ◽  
Solution Convergence ◽  
Satellite Geometry ◽  
System Bias ◽  
Point Positioning ◽  
Time Offset

This paper introduces a newly developed model for both single and dual-frequency precise point positioning (PPP), which combines GPS and Galileo observables. As is well known, a drawback of a single GNSS system is the availability of sufficient number of visible satellites in urban areas. Combining GPS and Galileo systems offers more visible satellites to users, which is expected to enhance the satellite geometry and the overall positioning solution. However, combining GPS and Galileo observables introduces additional biases which require rigorous modelling, including the GPS to Galileo time offset (GGTO) and the inter-system bias. This research introduces a new ionosphere-free linear combination model for GPS/Galileo PPP, which accounts for the additional errors and biases. An additional unknown is introduced in the least-squares estimation model to account for the additional biases of the GPS/Galileo PPP solution. It is shown that a sub-decimeter level positioning accuracy and 20% reduction in the solution convergence time can be achieved with the newly developed GPS/Galileo PPP model.

scholarly journals Precise Point Positioning Using World’s First Dual-Frequency GPS/GALILEO Smartphone

Sensors ◽  
2019 ◽  
Vol 19 (11) ◽  
pp. 2593 ◽  
Author(s):  
Abdelsatar Elmezayen ◽  
Ahmed El-Rabbany
Keyword(s):  
Real Time ◽  
Precise Point Positioning ◽  
Low Cost ◽  
Time Windows ◽  
Reference Station ◽  
Dual Frequency ◽  
Post Processing ◽  
Short Baseline ◽  
Positioning Accuracy ◽  
Point Positioning

The release of the world’s first dual-frequency GPS/Galileo smartphone, Xiaomi mi 8, in 2018 provides an opportunity for high-precision positioning using ultra low-cost sensors. In this research, the GNSS precise point positioning (PPP) accuracy of the Xiaomi mi 8 smartphone is tested in post-processing and real-time modes. Raw dual-frequency observations are collected over two different time windows from both of the Xiaomi mi 8 smartphone and a Trimble R9 geodetic-quality GNSS receiver using a short baseline, due to the lack of a nearby reference station to the observation site. The data sets are first processed in differential modes using Trimble business center (TBC) software in order to provide the reference positioning solution for both of the geodetic receiver and the smartphone. An in-house PPP software is then used to process the collected data in both of post-processing and real-time modes. Precise ephemeris obtained from the multi-GNSS experiment (MGEX) is used for post-processing PPP, while the new NAVCAST real-time GNSS service, Germany, is used for real-time PPP. Additionally, the real-time PPP solution is assessed in both of static and kinematic modes. It is shown that the dual-frequency GNSS smartphone is capable of achieving decimeter-level positioning accuracy, in both of post-processing and real-time PPP modes, respectively. Meter-level positioning accuracy is achieved in the kinematic mode.

scholarly journals Single-Frequency Precise Point Positioning Using Regional Dual-Frequency Observations

Sensors ◽  
2021 ◽  
Vol 21 (8) ◽  
pp. 2856
Author(s):  
Junping Zou ◽  
Ahao Wang ◽  
Jiexian Wang
Keyword(s):  
High Precision ◽  
Precise Point Positioning ◽  
Low Cost ◽  
Deformation Monitoring ◽  
Convergence Time ◽  
Single Frequency ◽  
Relative Positioning ◽  
Dual Frequency ◽  
Positioning Accuracy ◽  
Point Positioning

High-precision and low-cost single-frequency precise point positioning (SF-PPP) has been attracting more and more attention in numerous global navigation satellite system (GNSS) applications. To provide the precise ionosphere delay and improve the positioning accuracy of the SF-PPP, the dual-frequency receiver, which receives dual-frequency observations, is used. Based on the serviced precise ionosphere delay, which is generated from the dual-frequency observations, the high-precision SF-PPP is realized. To further improve the accuracy of the SF-PPP and shorten its convergence time, the double-differenced (DD) ambiguity resolutions, which are generated from the DD algorithm, are introduced. This method avoids the estimation of fractional cycle bias (FCB) for the SF-PPP ambiguity. Here, we collected data from six stations of Shanghai China which was processed, and the corresponding results were analyzed. The results of the dual-frequency observations enhanced SF-PPP realize centimeter-level positioning. The difference between the results of two stations estimated with dual-frequency observations enhanced SF-PPP were compared with the relative positioning results computed with the DD algorithm. Experimental results showed that the relative positioning accuracy of the DD algorithm is slightly better than that of the dual-frequency observations enhanced SF-PPP. This could be explained by the effect of the float ambiguity resolutions on the positioning accuracy. The data was processed with the proposed method for the introduction of the DD ambiguity into SF-PPP and the results indicated that this method could improve the positioning accuracy and shorten the convergence time of the SF-PPP. The results could further improve the deformation monitoring ability of SF-PPP.

scholarly journals Evaluation of Quad-Constellation GNSS Precise Point Positioning in Egypt

2017 ◽  
Vol 52 (1) ◽  
pp. 9-18
Author(s):  
Emad El Manaily ◽  
Mahmoud Abd Rabbou ◽  
Adel El-Shazly ◽  
Moustafa Baraka
Keyword(s):  
Urban Areas ◽  
Precise Point Positioning ◽  
Low Cost ◽  
Single Point ◽  
Convergence Time ◽  
Reference Station ◽  
Single Frequency ◽  
Major Drawback ◽  
Positioning Accuracy ◽  
Point Positioning

Abstract Commonly, relative GPS positioning technique is used in Egypt for precise positioning applications. However, the requirement of a reference station is usually problematic for some applications as it limits the operational range of the system and increases the system cost and complexity On the other hand; the single point positioning is traditionally used for low accuracy applications such as land vehicle navigation with positioning accuracy up to 10 meters in some scenarios which caused navigation problems especially in downtown areas. Recently, high positioning accuracy can be obtained through Precise Point Positioning (PPP) technique in which only once GNSS receiver is used. However, the major drawback of PPP is the long convergence time to reach to the surveying grade accuracy compared to the existing relative techniques. Moreover, the PPP accuracy is significantly degraded due to shortage in satellite availability in urban areas. To overcome these limitations, the quad constellation GNSS systems namely; GPS.GLONASS, Galileo and BeiDou can be combined to increase the satellite availability and enhance the satellite geometry which in turn reduces the convergence time. In Egypt, at the moment, the signals of both Galileo and BeiDou could be logged with limited number of satellites up to four and six satellites for both Systems respectively. In this paper, we investigated the performance of the Quad-GNSS positioning in both dual- and single-frequency ionosphere free PPP modes for both high accurate and low cost navigation application, respectively. The performance of the developed PPP models will be investigated through GNSS data sets collected at three Egyptian cities namely, Cairo, Alexandria and Aswan.

Sign in / Sign up

Export Citation Format

Share Document