scholarly journals Experimental Methodology to Determine Thermal Conductivity of Nanofluids by Using a Commercial Transient Hot-Wire Device

2021 ◽  
Vol 12 (1) ◽  
pp. 329
Author(s):  
Jose I. Prado ◽  
Uxía Calviño ◽  
Luis Lugo
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Theoretical Model ◽  
Ethylene Glycol ◽  
Experimental Methodology ◽  
Transient Hot Wire ◽  
Hot Wire ◽  
Experimental Procedure ◽  
Transfer Processes ◽  
The Mean

The lack of a standard experimental procedure to determine thermal conductivity of fluids is noticeable in heat transfer processes from practical and fundamental perspectives. Since a wide variety of techniques have been used, reported literature data have huge discrepancies. A common practice is using manufactured thermal conductivity meters for nanofluids, which can standardize the measurements but are also somewhat inaccurate. In this study, a new methodology to perform reliable measurements with a recent commercial transient hot-wire device is introduced. Accordingly, some extensively studied fluids in the literature (water, ethylene glycol, ethylene glycol:water mixture 50:50 vol%, propylene glycol, and n-tetradecane) covering the range 0.100 to 0.700 W m−1 K−1 were used to check the device in the temperature range 283.15 to 333.15 K. Deviations between the collected data and the theoretical model, and repeatabilities and deviations between reported and literature values, were analyzed. Systematic deviations in raw data were found, and a correction factor depending on the mean thermal conductivity was proposed to operate with nanofluids. Considering all tested effects, the expanded (k = 2) uncertainty of the device was set as 5%. This proposed methodology was also checked with n-hexadecane and magnesium-oxide-based n-tetradecane nanofluids.

Effect of Volume Fraction and Temperature on Thermal Conductivity of SiO2 Nanofluids

2011 ◽  
Vol 306-307 ◽  
pp. 1178-1181 ◽  
Author(s):  
Bao Jie Zhu ◽  
Wei Lin Zhao ◽  
Dong Dong Li ◽  
Jin Kai Li
Keyword(s):  
Thermal Conductivity ◽  
Ethylene Glycol ◽  
Volume Fraction ◽  
Experimental Results ◽  
Transient Hot Wire ◽  
Hot Wire ◽  
Transient Hot Wire Method ◽  
Wire Method ◽  
Thermal Conductivities

Thermal conductivities of two kinds of nanofluids (SiO2-water and SiO2-ethylene glycol) were measured by transient hot-wire method at different volume fraction and temperature. Influences of volume fraction of particles and temperature on thermal conductivities of nanofluids were analyzed. The Experimental results show that thermal conductivities of nanofluids are higher than those of base fluids, and increase with the increase of volume fraction and temperature. When approximately 0.5% volume fraction of SiO2nanoparticles are added into water and ethylene glycol at the temperature 50°C, the thermal conductivities are enhanced 46.2% and 62.8% respectively.

scholarly journals Apparatus for routine measurements of the thermal conductivity of ice cores

1999 ◽  
Vol 29 ◽  
pp. 151-154 ◽  
Author(s):  
Crescenzo Festa ◽  
Aristide Rossi
Keyword(s):  
Thermal Conductivity ◽  
Ice Cores ◽  
Maximum Temperature ◽  
Transient Hot Wire ◽  
Hot Wire ◽  
Standard Samples ◽  
Experimental Conditions ◽  
Heating Source ◽  
Central Segment ◽  
Wire Method

AbstractAn apparatus is described for measuring the thermal conductivity of ice by the transient hot-wire method. Thermal conductivity A, is determined by tracking the thermal pulse induced in the sample by a heating source consisting of a platinum resistor. A central segment of the same platinum heating resistor acts also as a thermal sensor. A heat pulse transferred to the ice for a period of 40s gives a maximum temperature increment of about 7-14°C. In good experimental conditions, the expected reproducibility of the measurements is within ±3%. The accuracy of the method depends on whether the instrument has been calibrated by reliable standard samples, certified by absolute methods.

scholarly journals Application and testing of a new simple experimental set-up for thermal conductivity measurements of liquids

2017 ◽  
Vol 21 (3) ◽  
pp. 1195-1202 ◽  
Author(s):  
Andrej Stanimirovic ◽  
Emila Zivkovic ◽  
Nenad Milosevic ◽  
Mirjana Kijevcanin
Keyword(s):  
Thermal Conductivity ◽  
Measurement Uncertainty ◽  
Thermophysical Properties ◽  
Deionized Water ◽  
Conductivity Measurements ◽  
Transient Hot Wire ◽  
Hot Wire ◽  
New Apparatus ◽  
Wire Method ◽  
Set Up

Transient hot wire method is considered a reliable and precise technique for measuring the thermal conductivity of liquids. The present paper describes a new transient hot wire experimental set-up and its initial testing. The new apparatus was tested by performing thermal conductivity measurements on substances whose reference thermophysical properties data existed in literature, namely on pure toluene and double distilled deionized water. The values of thermal conductivity measured in the temperature range 25 to 45 ?C deviated +2.2% to +3% from the literature data, while the expanded measurement uncertainty was estimated to be ?4%.

scholarly journals Experimental Investigation of Thermo-Physical Properties of Tri-Hybrid Nanoparticles in Water-Ethylene Glycol Mixture

2021 ◽  
Vol 18 (8) ◽  
Author(s):  
Anwar Ilmar RAMADHAN ◽  
Wan Hamzah AZMI ◽  
Rizalman MAMAT
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Ethylene Glycol ◽  
Physical Properties ◽  
Dynamic Viscosity ◽  
Volume Concentration ◽  
Hybrid Nanoparticles ◽  
Maximum Enhancement ◽  
Hybrid Nanofluids ◽  
Thermo Physical Properties

In recent years, research has focused on enhancing the thermo-physical properties of a single component nanofluid. Therefore, hybrid or composite nanofluids have been developed to improve heat transfer performance. The thermo-physical properties of the Al2O3-TiO2-SiO2 nanoparticles suspended in a base of water (W) and ethylene glycol (EG) at constant volume ratio of 60:40 and different volume concentrations were investigated. The experiment was conducted for the volume concentrations of 0.05, 0.1, 0.2, and 0.3% of Al2O3-TiO2-SiO2 nanofluids at different temperatures of 30, 40, 50, 60, and 70 °C. Thermal conductivity and dynamic viscosity measurements were carried out at temperatures ranging from 30 to 70 °C by using KD2 Pro Thermal Properties Analyzer and Brookfield LVDV III Ultra Rheometer, respectively. The highest thermal conductivity for tri-hybrid nanofluids was obtained at 0.3% volume concentration, and the maximum enhancement was increased up to 9% higher than the base fluid (EG/W). Tri-hybrid nanofluids with a volume concentration of 0.05% gave the lowest effective thermal conductivity of 4.8 % at 70 °C temperature. Meanwhile, the dynamic viscosity of the tri-hybrid nanofluids was influenced by volume concentration and temperature. Furthermore, tri-hybrid nanofluids behaved as a Newtonian fluid for volume concentrations from 0.05 to 3.0%. The properties enhancement ratio (PER) estimated that the tri-hybrid nanofluids will aid in heat transfer for all samples in the present. The new correlations for thermal conductivity and dynamic viscosity of tri-hybrid nanofluids were developed with minimum deviation. As a conclusion, the combination of the enhancement in thermal conductivity and dynamic viscosity for tri-hybrid at 0.3% volume concentration was found the optimum condition with more advantage for heat transfer than other concentrations.

Analysis of the Transient Hot-Wire Method to Measure Thermal Conductivity of Silica Aerogel: Influence of Wire Length, and Radiation Properties

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
Ellann Cohen ◽  
Leon Glicksman
Keyword(s):  
Thermal Conductivity ◽  
Silica Aerogel ◽  
Test Method ◽  
Wire Radius ◽  
Wire Length ◽  
Transient Hot Wire ◽  
Hot Wire ◽  
End Effects ◽  
Transient Hot Wire Method ◽  
Wire Method

When the transient hot-wire method is used to measure the thermal conductivity of very low thermal conductivity silica aerogel (in the range of 10 mW/m·K at 1 atm) end effects due to the finite wire size and radiation corrections must be considered. An approximate method is presented to account for end effects with realistic boundary conditions. The method was applied to small experimental samples of the aerogel using different wire lengths. Initial conductivity results varied with wire length. This variation was eliminated by the use of the end effect correction. The test method was validated with the NIST (National Institute of Standards and Technology) Standard Reference Material 1459, fumed silica board to within 1 mW/m·K. The aerogel is semitransparent. Due to the small wire radius and short transient, radiation heat transfer may not be fully accounted for. In a full size aerogel panel radiation will augment the phonon conduction by a larger amount.

Sign in / Sign up

Export Citation Format

Share Document