Enhanced CH4 Production from Corn-Stalk Pyrolysis Using Ni-5CeO2/MCM-41 as a Catalyst

Production of syngas from lignocellulosic biomass though pyrolysis is a promising solution for the large-scale utilization of biomass. However, current pyrolysis approaches suffer from the relative low product yield and selectivity, limiting their practical application. To solve this problem, a series of nickel-based catalysts including Ni/MCM-41, Ni-5CeO2/MCM-41, and Ni-5La2O3/MCM-41 were prepared and characterized by transmission electron microscopy (TEM), N2 adsorption–desorption, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and H2-temperature-programmed reaction (TPR) analysis. It was observed that the simultaneous addition of Ni and CeO2 to MCM-41 could increase the reducibility of Ni and the number of active Ni0 sites on the surface of the catalyst. Consequently, Ni-5CeO2/MCM-41 gave a CH4 yield of 14.6 mmol/g, which is remarkably higher than that (10.5 mmol/g) obtained in the absence of the catalyst. Meanwhile, the CO and H2 yields increased slightly, while the CO2 yield decreased slightly. Therefore, the improved CH4 yield and selectivity was mainly due to the increased decomposition of tarry compounds catalyzed by Ni/MCM-41 with the assistance of CeO2.

Download Full-text

Catalytic Activity of Mixed Al2O3-ZrO2 Oxides for Glucose Conversion into 5-Hydroxymethylfurfural

Catalysts ◽

10.3390/catal10080878 ◽

2020 ◽

Vol 10 (8) ◽

pp. 878 ◽

Cited By ~ 1

Author(s):

Benjamín Torres-Olea ◽

Sandra Mérida-Morales ◽

Cristina García-Sancho ◽

Juan Antonio Cecilia ◽

Pedro Maireles-Torres

Keyword(s):

Catalytic Activity ◽

Photoelectron Spectroscopy ◽

Molar Ratio ◽

X Ray ◽

Zirconium Oxides ◽

Transmission Electron ◽

Scanning Transmission ◽

Secondary Reactions ◽

Temperature Programmed ◽

Adsorption Desorption

In the present work, a series of catalysts based on aluminum and zirconium oxides was studied for the transformation of glucose into 5-hydroxymethylfurfural. These catalysts were characterized by using experimental techniques, such as X-ray diffraction, N2 adsorption–desorption at −196 °C, X-ray photoelectron spectroscopy, temperature-programmed desorption of NH3 and CO2, and scanning transmission electron microscopy. The catalytic behavior in glucose dehydration was evaluated in a water-methyl isobutyl ketone biphasic system, in the presence of CaCl2, in order to minimize losses due to unwanted secondary reactions. High glucose conversion and 5-hydroxymethylfurfural (HMF) yield values were obtained in the presence of an Al(Zr)Ox catalyst with an Al:Zr molar ratio of 7:3, reaching 97% and 47%, respectively, at 150 °C after 120 min. Under tested conditions, this catalyst retained most of its catalytic activity for four reuses.

Download Full-text

Highly active carbon nanotube–promoted Rh-Mn-Li/SiO2 catalysts for the synthesis of C2+ oxygenates from syngas

Journal of Chemical Research ◽

10.1177/1747519820984728 ◽

2021 ◽

pp. 174751982098472

Author(s):

Jun Yu ◽

Ying Han ◽

Guoqing Chen ◽

Xiuzhen Xiao ◽

Haifang Mao ◽

...

Keyword(s):

Carbon Nanotubes ◽

Photoelectron Spectroscopy ◽

Co Hydrogenation ◽

X Ray ◽

Highly Active ◽

Transmission Electron ◽

Co Insertion ◽

Temperature Programmed Surface Reaction ◽

Temperature Programmed ◽

Oxygenate Synthesis

The effect of carbon nanotubes on the catalytic properties of Rh-Mn-Li/SiO2 catalysts was investigated for CO hydrogenation. The catalysts were comprehensively characterized by means of X-ray power diffraction, N2 sorption, transmission electron microscope, H2–temperature-programmed reduction, CO–temperature-programmed desorption, temperature-programmed surface reaction, and X-ray photoelectron spectroscopy. The results showed that an appropriate amount of carbon nanotubes can be attached to the surface of the SiO2 sphere and can improve the Rh dispersion. Moderate Rh-Mn interaction can be obtained by doping with the appropriate amount of carbon nanotubes, which promotes the formation of strongly adsorbed CO and facilitates the progress of CO insertion, resulting in the increase in the selectivity of C2+ oxygenate synthesis.

Download Full-text

FeYO3@rGO nanocomposites: Synthesis, characterization and application in photooxidative degradation of atrazine under visible light

Materials Express ◽

10.1166/mex.2021.1957 ◽

2021 ◽

Vol 11 (5) ◽

pp. 706-716

Author(s):

Nada D. Al-Khthami ◽

Tariq Altalhi ◽

Mohammed Alsawat ◽

Mohamed S. Amin ◽

Yousef G. Alghamdi ◽

...

Keyword(s):

Visible Light ◽

Photoelectron Spectroscopy ◽

Sol Gel ◽

Bandgap Energy ◽

X Ray Diffraction ◽

X Ray ◽

Transmission Electron ◽

Reduced Graphene ◽

Structural Surface ◽

Adsorption Desorption

Different organic pollutants have been remediated photo catalytically by applying perovskite photocatalysts. Atrazine (ATR) is a pesticide commonly detected as a pollutant in drinking, surface and ground water. Herein, FeYO3@rGO heterojunction was synthesized and applied for photooxidation decomposition of ATR. First, FeYO 3nanoparticles (NPs) were prepared via routine sol-gel. After that, FeYO3 NPs were successfully incorporated with different percentages (5, 10, 15 and 20 wt.%) of reduced graphene oxide (rGO) in the synthesis of novel FeYO3@rGO photocatalyst. Morphological, structural, surface, optoelectrical and optical characteristics of constructed materials were identified via X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Transmission electron microscopy (TEM), adsorption/desorption isotherms, diffusive reflectance (DR) spectra, and photoluminescence response (PL). Furthermore, photocatalytic achievement of the constructed materials was evaluated via photooxidative degradation of ATR. Various investigations affirmed the usefulness of rGO incorporation on the advancement of formed photocatalysts. Actually, novel nanocomposite containing rGO (15 wt.%) possessed diminished bandgap energy, as well as magnified visible light absorption. Furthermore, such nanocomposite presented exceptional photocatalytic achievement when exposed to visible light as ATR was perfectly photooxidized over finite amount (1.6 g · L-1) from the optimized photocatalyst when illuminated for 30 min. The advanced photocatalytic performance of constructed heterojunctions could be accredited mainly to depressed recombination amid induced charges. The constructed FeYO3@rGO nanocomposite is labelled as efficient photocatalyst for remediation of herbicides from aquatic environments.

Download Full-text

A Facile Strategy to Fabricate Nanoscale Zero-Valent Iron Decorated Graphene Oxide Composite for Dechloridation of Trichloroacetic Acid in Water

Journal of Nanoscience and Nanotechnology ◽

10.1166/jnn.2018.16374 ◽

2018 ◽

Vol 18 (12) ◽

pp. 8252-8257 ◽

Cited By ~ 1

Author(s):

Huixuan Zhang ◽

Xinyi Zhang ◽

Ruonan Guo ◽

Qingfeng Cheng ◽

Xiuwen Cheng

Keyword(s):

Graphene Oxide ◽

Photoelectron Spectroscopy ◽

Sewage Treatment ◽

Reduction Process ◽

Zero Valent Iron ◽

Chlorinated Organic Compounds ◽

X Ray ◽

Transmission Electron ◽

Nanoscale Zero Valent Iron ◽

Adsorption Desorption

In this study, nanoscale zero-valent iron decorated graphene oxide (NZVI/GO) composite was fabricated through a reduction process in the presence of sodium borohydride (NaBH4) solution. Subsequently, physicochemical properties of the NZVI/GO composites were characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), N2 adsorption/desorption, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transformation infrared spectroscopy (FT-IR) and Raman spectra. Results indicated that Fe species existed in the form of Fe0, which uniformly dispersed on the surface of GO. Furthermore, the performance of NZVI/GO was evaluated by the degradation of tichloroacetic acid (TCAA). TCAA can be rapidly degraded by NZVI/GO. This paper provides a promising strategy to synthesize versatile catalyst which would be potentially applied in sewage treatment to degrade chlorinated organic compounds.

Download Full-text

Synthesis and characterizations of TiN–SBA-15 mesoporous materials for CO2 dry reforming enhancement

Pure and Applied Chemistry ◽

10.1515/pac-2019-0806 ◽

2020 ◽

Vol 92 (4) ◽

pp. 545-556

Author(s):

Maslin Chotirach ◽

Supawan Tantayanon ◽

Duangamol Nuntasri Tungasmita ◽

Junliang Sun ◽

Sukkaneste Tungasmita

Keyword(s):

Photoelectron Spectroscopy ◽

Synthesis Method ◽

High Specific Surface Area ◽

Dry Reforming ◽

Dry Reforming Of Methane ◽

Ni Catalyst ◽

X Ray ◽

Novel Approach ◽

Temperature Programmed ◽

Adsorption Desorption

AbstractA novel approach of titanium nitride (TiN) incorporated into SBA-15 framework was developed using one-step hydrothermal synthesis method. TiN contents up to ~18 wt% were directly dispersed in a synthetic gel under a typical strong acidic condition. The physico-chemical characteristics and the surface properties were investigated by means of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), N2 adsorption-desorption, field emission scanning electron microscope (FESEM) equipped with energy dispersive X-ray spectroscopy (EDS), wavelength dispersive X-ray fluorescence (WDXRF) and CO2-temperature programmed desorption (CO2-TPD). The results indicated that the highly ordered mesostructured was effectively maintained with high specific surface area of 532–685 m2g−1. The basicity of the modified SBA-15 increased with rising TiN loading. These modified materials were applied as a support of Ni catalyst in dry reforming of methane (DRM). Their catalytic behavior possessed superior conversions for both CO2 and CH4 with the highest H2/CO ratio (0.83) as well as 50 % lower carbon formation, compared to bare SBA-15 support.

Download Full-text

Bulk Versus Surface Modification of Alumina with Mn and Ce Based Oxides for CH4 Catalytic Combustion

Materials ◽

10.3390/ma12111771 ◽

2019 ◽

Vol 12 (11) ◽

pp. 1771 ◽

Cited By ~ 2

Author(s):

Stefan Neatu ◽

Mihaela M. Trandafir ◽

Adelina Stănoiu ◽

Ovidiu G. Florea ◽

Cristian E. Simion ◽

...

Keyword(s):

Photoelectron Spectroscopy ◽

Catalytic Combustion ◽

Mixed Oxides ◽

Sol Gel ◽

Nitrogen Adsorption ◽

X Ray Diffraction ◽

X Ray ◽

Temperature Programmed ◽

Catalytic Combustion Of Methane ◽

Adsorption Desorption

This study presents the synthesis and characterization of lanthanum-modified alumina supported cerium–manganese mixed oxides, which were prepared by three different methods (coprecipitation, impregnation and citrate-based sol-gel method) followed by calcination at 500 °C. The physicochemical properties of the synthesized materials were investigated by various characterization techniques, namely: nitrogen adsorption-desorption isotherms, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and H2–temperature programmed reduction (TPR). This experimental study demonstrated that the role of the catalytic surface is much more important than the bulk one. Indeed, the incipient impregnation of CeO2–MnOx catalyst, supported on an optimized amount of 4 wt.% La2O3–Al2O3, provided the best results of the catalytic combustion of methane on our catalytic micro-convertors. This is mainly due to: (i) the highest pore size dimensions according to the Brunauer-Emmett-Teller (BET) investigations, (ii) the highest amount of Mn4+ or/and Ce4+ on the surface as revealed by XPS, (iii) the presence of a mixed phase (Ce2MnO6) as shown by X-ray diffraction; and (iv) a higher reducibility of Mn4+ or/and Ce4+ species as displayed by H2–TPR and therefore more reactive oxygen species.

Download Full-text

Hydrogenative Cyclization of Levulinic Acid to γ-Valerolactone with Methanol and Ni-Fe Bimetallic Catalysts

Catalysts ◽

10.3390/catal10091096 ◽

2020 ◽

Vol 10 (9) ◽

pp. 1096

Author(s):

Ligang Luo ◽

Xiao Han ◽

Qin Zeng

Keyword(s):

Photoelectron Spectroscopy ◽

Levulinic Acid ◽

Hydrogen Donor ◽

Effect Of Temperature ◽

X Ray ◽

Transmission Electron ◽

Ft Ir ◽

Temperature Programmed

A series of Ni-Fe/SBA-15 catalysts was prepared and tested for the catalytic hydrogenation of levulinic acid to γ-valerolactone, adopting methanol as the only hydrogen donor, and investigating the synergism between Fe and Ni, both supported on SBA-15, towards this reaction. The characterization of the synthesized catalysts was carried out by XRD (X-ray powder diffraction), TEM (transmission electron microscopy), H2-TPD (hydrogen temperature-programmed desorption), XPS (X-ray photoelectron spectroscopy), and in situ FT-IR (Fourier transform–infrared spectroscopy) techniques. H2-TPD and XPS results have shown that electron transfer occurs from Fe to Ni, which is helpful both for the activation of the C=O bond and for the dissociative activation of H2 molecules, also in agreement with the results of the in situ FT-IR spectroscopy. The effect of temperature and reaction time on γ-valerolactone production was also investigated, identifying the best reaction conditions at 200 °C and 180 min, allowing for the complete conversion of levulinic acid and the complete selectivity to γ-valerolactone. Moreover, methanol was identified as an efficient hydrogen donor, if used in combination with the Ni-Fe/SBA-15 catalyst. The obtained results are promising, especially if compared with those obtained with the traditional and more expensive molecular hydrogen and noble-based catalysts.

Download Full-text

Nanosized V-Ce Oxides Supported on TiO2 as a Superior Catalyst for the Selective Catalytic Reduction of NO

Catalysts ◽

10.3390/catal10020202 ◽

2020 ◽

Vol 10 (2) ◽

pp. 202

Author(s):

Long Lu ◽

Xueman Wang ◽

Chunhua Hu ◽

Ying Liu ◽

Xiongbo Chen ◽

...

Keyword(s):

Low Temperature ◽

Selective Catalytic Reduction ◽

Photoelectron Spectroscopy ◽

Catalytic Reduction ◽

X Ray Diffraction ◽

X Ray ◽

Transmission Electron ◽

Redox Capacity ◽

Scr Of No ◽

Temperature Programmed

Nanosized V-Ce oxides supported on TiO2 (VCT) were prepared and utilized in the low-temperature selective catalytic reduction (SCR) of NO with NH3. Compared with the other V-Ce oxides-based catalysts supported on Al2O3, ZrO2, and ZSM-5, VCT showed the best SCR activity in a low-temperature range. The NOx conversion of 90% could be achieved at 220 °C. Characterizations including X-ray diffraction (XRD), scanning election micrograph (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), temperature-programmed desorption with NH3 (NH3-TPD), and temperature-programmed reduction with H2 (H2-TPR) showed that V1.05Ce1/TiO2 exhibited a good dispersion of V2O5, enrichment of surface Ce3+ and chemical-absorbed oxygen, and excellent redox capacity and acidity, which resulted in the best SCR performance at low temperature.

Download Full-text

Preparation, Characterization, and Performance Analysis of S-Doped Bi2MoO6 Nanosheets

Nanomaterials ◽

10.3390/nano9091341 ◽

2019 ◽

Vol 9 (9) ◽

pp. 1341 ◽

Cited By ~ 1

Author(s):

Ruiqi Wang ◽

Duanyang Li ◽

Hailong Wang ◽

Chenglun Liu ◽

Longjun Xu

Keyword(s):

Photoelectron Spectroscopy ◽

Degradation Rate ◽

X Ray Diffraction ◽

Photo Degradation ◽

X Ray ◽

Transmission Electron ◽

Ft Ir ◽

And Performance ◽

Adsorption Desorption ◽

Excellent Stability

S-doped Bi2MoO6 nanosheets were successfully synthesized by a simple hydrothermal method. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM), N2 adsorption–desorption isotherms, Raman spectroscopy, Fourier transform infrared spectroscopy (FT-IR), elemental mapping spectroscopy, photoluminescence spectra (PL), X-ray photoelectron spectroscopy (XPS), and UV-visible diffused reflectance spectra (UV-vis DRS). The photo-electrochemical performance of the samples was investigated via an electrochemical workstation. The S-doped Bi2MoO6 nanosheets exhibited enhanced photocatalytic activity under visible light irradiation. The photo-degradation rate of Rhodamine B (RhB) by S-doped Bi2MoO6 (1 wt%) reached 97% after 60 min, which was higher than that of the pure Bi2MoO6 and other S-doped products. The degradation rate of the recovered S-doped Bi2MoO6 (1 wt%) was still nearly 90% in the third cycle, indicating an excellent stability of the catalyst. The radical-capture experiments confirmed that superoxide radicals (·O2−) and holes (h+) were the main active substances in the photocatalytic degradation of RhB by S-doped Bi2MoO6.

Download Full-text

ZnFe2O4-TiO2Nanoparticles within Mesoporous MCM-41

The Scientific World JOURNAL ◽

10.1100/2012/480527 ◽

2012 ◽

Vol 2012 ◽

pp. 1-8 ◽

Cited By ~ 5

Author(s):

Aidong Tang ◽

Yuehua Deng ◽

Jiao Jin ◽

Huaming Yang

Keyword(s):

Sol Gel ◽

Rutile Phase ◽

Band Gap Energy ◽

Molar Ratio ◽

X Ray Diffraction ◽

X Ray ◽

Transmission Electron ◽

Agglomeration Of Nanoparticles ◽

Adsorption Desorption ◽

Mcm 41

A novel nanocomposite ZnFe2O4-TiO2/MCM-41 (ZTM) was synthesized by a sol-gel method and characterized through X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), N2adsorption-desorption, Raman spectroscopy, and ultraviolet visible (UV-vis) spectrophotometry. The results confirmed the incorporation of ZnFe2O4-TiO2nanoparticles inside the pores of the mesoporous MCM-41 host without destroying its integrity. ZnFe2O4nanoparticles can inhibit the transformation of anatase into rutile phase of TiO2. Incorporation of ZnFe2O4-TiO2within MCM-41 avoided the agglomeration of nanoparticles and reduced the band gap energy of TiO2to enhance its visible light photocatalytic activity. UV-vis absorption edges of ZTM nanocomposites redshifted with the increase of Zn/Ti molar ratio. The nanocomposite approach could be a potential choice for enhancing the photoactivity of TiO2, indicating an interesting application in the photodegradation and photoelectric fields.

Download Full-text