scholarly journals Temperature Study during the Edge Trimming of Carbon Fiber-Reinforced Plastic [0]8/Ti6Al4V Stack Material

2021 ◽  
Vol 5 (5) ◽  
pp. 137
Author(s):  
Arquimedes Castillo-Morales ◽  
Xavier Rimpault ◽  
Jean-François Chatelain ◽  
Gilbert Lebrun
Keyword(s):  
Carbon Fiber ◽  
Cutting Speed ◽  
Machining Process ◽  
Carbon Fiber Reinforced Plastic ◽  
Drilling Process ◽  
Fiber Reinforced ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Carbon Fiber Reinforced ◽  
Edge Trimming

Carbon Fiber-Reinforced Plastic (CFRP) and Titanium alloy (Ti6Al4V) stacks are used extensively in the modern aerospace industry thanks to their outstanding mechanical properties and resistance to thermal load applications. Machining the CFRP/Ti6Al4V stack is a challenge and is complicated by the differences in each constituent materials’ machinability. The difficulty arises from the matrix degradation of the CFRP material caused by the heat generated during the machining process, which is a consequence of the low thermal conductivity of Ti6Al4V material. In most cases, CFRP and Ti6Al4V materials are stacked and secured together using rivets or bolts. This results in extra weight, while the drilling process required for such an assembly may damage the CFRP material. To overcome these issues, some applications employ an assembly that is free of bolts or rivets, and which uses adhesives or an adapted curing process to bond both materials together. The present research analyzes a thermal distribution and its effect on quality during the edge trimming process of a CFRP/Ti6Al4V stack assembly. Different types of tools and cutting parameters are compared using thermocouples embedded within the material and others on the tool cutting edge. In contrast to previous studies, the feed rate was the most significant factor affecting the cutting temperature and quality of the workpiece, while the cutting speed had no significant impact. The temperature in the workpiece increases as the feed per tooth decreases.

Laminate Orientation Effect on Drilling of Carbon Fiber Reinforced Plastic Composites

2013 ◽  
Vol 315 ◽  
pp. 768-772
Author(s):  
Ismail Mahamad Hakimi ◽  
S. Sharif ◽  
Denni Kurniawan
Keyword(s):  
Carbon Fiber ◽  
Fiber Orientation ◽  
Thrust Force ◽  
Machining Process ◽  
Carbon Fiber Reinforced Plastic ◽  
Fiber Reinforced ◽  
Fiber Reinforced Plastic ◽  
Cfrp Composites ◽  
Reinforced Plastic ◽  
Carbon Fiber Reinforced

Carbon fiber reinforced plastic (CFRP) composites are often used in combination with other materials, requiring it to be machined during fabrication of a structure. Drilling as the most common machining process of CFRP is complex often results in delamination of the composites. The complexity is contributed by CFRP composites fiber orientation which can be of unidirectional or quasi-isotropic type depending on the applications. This study reviews the machinability of CFRP composites by considering fiber orientation and machining conditions used during drilling. Their relation with machining thrust force which leads to delamination is the central theme. An insight in obtaining delamination-free holes is also discussed.

Deterioration of polycrystalline diamond tools in milling of carbon-fiber-reinforced plastic

2016 ◽  
Vol 51 (16) ◽  
pp. 2277-2290 ◽  
Author(s):  
Zhenyuan Jia ◽  
Youliang Su ◽  
Bin Niu ◽  
Yu Bai ◽  
Guangjian Bi
Keyword(s):  
Carbon Fiber ◽  
Diamond Tool ◽  
Cutting Speed ◽  
Tool Material ◽  
Polycrystalline Diamond ◽  
Carbon Fiber Reinforced Plastic ◽  
Fiber Reinforced ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Carbon Fiber Reinforced

The cutting edge of the polycrystalline diamond tool easily blunts in high-speed milling of carbon-fiber-reinforced plastic with the tool deterioration. It aggravates the burrs damage due to the change in the tool–material interaction. Therefore, this paper analyzes the tool–material interaction in milling of carbon-fiber-reinforced plastic based on the material-removal mechanism to investigate the tool deterioration mechanism. It reveals that there are two main reasons for the tool deterioration: the extreme crashing and ploughing of the uncut fibers on the tool, and the serious impact of fibers strongly supported on the cutting edge. An indirect measure method is proposed to quantify the tool deterioration including the ploughing-caused wear and impact-caused microchipping. Furthermore, the milling tests are performed to evaluate the tool deterioration under different cutting speeds in the range of 7.33–9.42 m/s. Meanwhile, a modified mathematical model of tool life is proposed based on a strict burr specification in milling of the carbon-fiber-reinforced plastics. Polycrystalline diamond tool has the longest life with the run-in wear and the quasi-steady-state wear for 7.33 m/s cutting speed, and the life rapidly decreases with the increase in the cutting speed in this range. For the cutting speed larger than 8.37 m/s, the wear resistance of polycrystalline diamond tool is very low, because the accelerated state wear occurs instead of the quasi-steady-state wear. Thus, the optimization of the tool geometry and the assisted lubrication should be applied for its improvement.

Study on the Surface Delamination in Milling Carbon Fiber Reinforced Plastic with PCD Tool

2011 ◽  
Vol 381 ◽  
pp. 1-5 ◽  
Author(s):  
Yong Guo Wang ◽  
Chang Yu Sun ◽  
Xiang Ping Yan ◽  
Ke Ren Jiang
Keyword(s):  
Carbon Fiber ◽  
Cutting Speed ◽  
Carbon Fiber Reinforced Plastic ◽  
Fiber Reinforced ◽  
Fiber Reinforced Plastic ◽  
Pcd Tool ◽  
Reinforced Plastic ◽  
Cutting Velocity ◽  
Carbon Fiber Reinforced ◽  
Surface Delamination

The factors which lead to the surface delamination existing in milling carbon fiber reinforced plastic (CFRP) with PCD tool have been studied. The surface delamination is summarized by analyzing the experiment results based on studying cutting velocity and cutting feed. Experimental results show that the increasing cutting feed leads to the increment of cutting force which in turn causes the increasing delamination of CFRP materials. Moreover, the delamination initial reduces with the increasing cutting speed from 6000 to 10000r/min but subsequently raises when the cutting speed vary from 10000 to 15000r/min with the same cutting feed of 0.08mm/z.

Hole quality and tool wear when dry drilling of a new developed metal/composite co-cured material

2020 ◽  
Vol 234 (6-7) ◽  
pp. 980-992 ◽  
Author(s):  
Fan Zou ◽  
Jiaqiang Dang ◽  
Xiaojiang Cai ◽  
Qinglong An ◽  
Weiwei Ming ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Tool Wear ◽  
Attitude Control ◽  
Carbon Fiber Reinforced Plastic ◽  
Drilling Process ◽  
Metal Composite ◽  
Fiber Reinforced ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Carbon Fiber Reinforced

The new developed metal/composite co-cured material composed of carbon fiber–reinforced plastic and Al phases has been increasingly applied for manufacturing of attitude control flywheel in aerospace industry. However, drilling of co-cured material is still a challenging task to produce holes with high quality and low cost in the assembly chain and dynamic balance debugging of attitude control flywheel. In other words, the relevant mechanisms and experimental findings involved in the drilling process of carbon fiber–reinforced plastic/Al co-cured material is not clearly defined, which impedes the progress of attitude control flywheel production. To this end, this article specially addresses the experimental studies on the drilling process of carbon fiber–reinforced plastic/Al co-cured material with standard TiAlN-coated cemented carbide twist drill. The significance of this work aims to reveal the regardful cutting responses of the hole characteristics and tool wear modes during the practical drilling process of co-cured material. A full factorial experiment including three levels of feed rate and four levels of cutting speed was performed. The hole diameter shows different values in different positions while it indicates consistent pattern regardless of the cutting variables: the largest in the Al phase, followed by the upper and lower carbon fiber–reinforced plastic phases, respectively. Grooves and matrix degradation are the major machining defects for carbon fiber–reinforced plastic layers, while a great chip debris adhered to the machined surface is the case for Al layer. Subsequent wear analysis showed that abrasion was mainly maintained at the vicinity of major/minor cutting edges and drill edge corner, followed by chip adhesion on the chisel edge region. Carbide substrate of drill flank face is exposed, and thereafter cavities are formed under the strong mechanical abrasion. These results could provide several implications for industrial manufacturers during the attitude control flywheel production.

scholarly journals Stressing State Analysis of Reinforced Concrete Beam Strengthened by CFRP Sheet with Anchoring Device

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 576
Author(s):  
Liang Luo ◽  
Jie Lai ◽  
Jun Shi ◽  
Guorui Sun ◽  
Jie Huang ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Strain Distribution ◽  
Carbon Fiber Reinforced Plastic ◽  
Rc Beams ◽  
Fiber Reinforced ◽  
Strain Distribution Pattern ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Cfrp Sheet ◽  
Carbon Fiber Reinforced

This paper investigates the working performance of reinforcement concrete (RC) beams strengthened by Carbon-Fiber-Reinforced Plastic (CFRP) with different anchoring under bending moment, based on the structural stressing state theory. The measured strain values of concrete and Carbon-Fiber-Reinforced Plastic (CFRP) sheet are modeled as generalized strain energy density (GSED), to characterize the RC beams’ stressing state. Then the Mann–Kendall (M–K) criterion is applied to distinguish the characteristic loads of structural stressing state from the curve, updating the definition of structural failure load. In addition, for tested specimens with middle anchorage and end anchorage, the torsion applied on the anchoring device and the deformation width of anchoring device are respectively set parameters to analyze their effects on the reinforcement performance of CFRP sheet through comparing the strain distribution pattern of CFRP. Finally, in order to further explore the strain distribution of the cross-section and analyze the stressing-state characteristics of the RC beam, the numerical shape function (NSF) method is proposed to reasonably expand the limited strain data. The research results provide a new angle of view to conduct structural analysis and a reference to the improvement of reinforcement effect of CFRP.

Study on the mechanism of inhomogeneous microdamage in short-pulse laser processing of carbon fiber reinforced plastic

2021 ◽  
pp. 073168442098359
Author(s):  
Luyao Xu ◽  
Jiuru Lu ◽  
Kangmei Li ◽  
Jun Hu
Keyword(s):  
Carbon Fiber ◽  
Pulse Energy ◽  
Short Pulse ◽  
Heterogeneous Material ◽  
Carbon Fiber Reinforced Plastic ◽  
Fiber Reinforced ◽  
Processing Efficiency ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Carbon Fiber Reinforced

In this article, a micro-heterogeneous material simulation model with carbon fiber and resin phase about laser ablation on carbon fiber reinforced plastic (CFRP) is established by Ansys. The ablation process of CFRP by nanosecond ultraviolet laser is simulated, and the mechanism of pulse energy and spot spacing on the heat-affected zone (HAZ) is studied, then the process parameters are optimized with the goal of HAZ size and processing efficiency, and finally the validity of the model is verified by experiments. It is found that the residual gradient and the width of the radial HAZ increase with the increase of the spot spacing, and the width of the axial HAZ decreases slightly with the increase of the spot spacing, which indicates the existence of the optimal spot spacing. Second, the ablation depth increases with the increase of the pulse energy, and the carbon fiber retains a relatively complete degree of exposure when the pulse energy is low, which has a certain guiding significance for the cleaning and bonding of CFRP.

Sign in / Sign up

Export Citation Format

Share Document