scholarly journals Small–Scale Experimental Investigation of Fatigue Performance Improvement of Ship Hatch Corner with Shot Peening Treatments by Considering Residual Stress Relaxation

2021 ◽  
Vol 9 (4) ◽  
pp. 419
Author(s):  
Jin Gan ◽  
Zi’ang Gao ◽  
Yiwen Wang ◽  
Zhou Wang ◽  
Weiguo Wu
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Fatigue Life ◽  
Stress Relaxation ◽  
Stress Field ◽  
Shot Peening ◽  
Compressive Residual Stress ◽  
Fatigue Performance ◽  
Residual Stress Field ◽  
Residual Stress Relaxation

Ship hatch corner is a common structure in a ship and its fatigue problem has always been one of the focuses in ship engineering due to the long–term high–stress concentration state during the ship’s life. For investigating the fatigue life improvement of the ship hatch corner under different shot peening (SP) treatments, a series of fatigue tests, residual stress and surface topography measurements were conducted for SP specimens. Furthermore, the distributions of the surface residual stress are measured with varying numbers of cyclic loads, investigating the residual stress relaxation during cyclic loading. The results show that no matter which SP process parameters are used, the fatigue lives of the shot–peened ship hatch corner specimens are longer than those at unpeened specimens. The relaxation rate of the residual stress mainly depends on the maximum compressive residual stress (σRSmax) and the depth of the maximum compressive residual stress (δmax). The larger the values of σRSmax and δmax, the slower the relaxation rates of the residual stress field. The results imply that the effect of residual stress field and surface roughness should be considered comprehensively to improve the fatigue life of the ship hatch corner with SP treatment. The increase in peening intensity (PI) within a certain range can increase the depth of the compressive residual stress field (CRSF), so the fatigue performance of the ship hatch corner is improved. Once the PI exceeds a certain value, the surface damage caused by the increase in surface roughness will not be offset by the CRSF and the fatigue life cannot be improved optimally. This research provides an approach of fatigue performance enhancement for ship hatch corners in engineering application.

3D Computational Simulation of Multi-Impact Shot Peening

2012 ◽  
Vol 1485 ◽  
pp. 35-40
Author(s):  
Juan Solórzano-López ◽  
Francisco Alfredo García-Pastor
Keyword(s):  
Residual Stress ◽  
Fatigue Life ◽  
Stress Field ◽  
Surface Treatment ◽  
Shot Peening ◽  
Compressive Residual Stress ◽  
Fatigue Testing ◽  
Computational Simulation ◽  
Target Material ◽  
Residual Stress Field

ABSTRACTShot peening is a widely applied surface treatment in a number of manufacturing processes in several industries including automotive, mechanical and aeronautical. This surface treatment is used with the aim of increasing surface toughness and extending fatigue life. The increased performance during fatigue testing of the peened components is mainly the result of the sub-surface compressive residual stress field resulting from the plastic deformation of the surface layers of the target material, caused by the high-velocity impact of the shot. This compressive residual stress field hinders the propagation and coalescence of cracks during the second stage of fatigue testing, effectively increasing the fatigue life well beyond the expected life of a non-peened component.This paper describes a 3D computational model of spherical projectiles impacting simultaneously upon a flat surface. The multi-impact model was developed in ABAQUS/Explicit using finite element method (FEM) and taking into account controlling parameters such as the velocity of the projectiles, their incidence angle and different impact locations in the target surface. Additionally, a parametric study of the physical properties of the target material was carried out in order to assess the effect of temperature on the residual stress field.The simulation has been able to successfully represent a multi-impact processing scenario, showing the indentation caused by each individual shot, as well as the residual stress field for each impact and the interaction between each one of them. It has been found that there is a beneficial effect on the residual stress field magnitude when shot peening is carried out at a relatively high temperature. The results are discussed in terms of the current shot-peening practice in the local industry and the leading edge developments of new peening technologies. Finally, an improved and affordable processing route to increase the fatigue life of automotive components is suggested.

A Study on the Fatigue Characteristics of Al6061-T651 by Shot Peening Velocity

2006 ◽  
Vol 326-328 ◽  
pp. 1093-1096 ◽  
Author(s):  
Won Jo Park ◽  
Sun Chul Huh ◽  
Sung Ho Park
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Fatigue Life ◽  
Shot Peening ◽  
High Speed ◽  
Compressive Residual Stress ◽  
Velocity Increase ◽  
Fatigue Characteristics ◽  
Height Increase ◽  
Small Steel

Small steel ball is utilized in Shot peening process. Called “shot ball” are shot in high speed on the surface of metal. When the shot ball hit the surface, it makes plastic deformation and bounce off, that increase the fatigue life by compressive residual stress on surface. In this study, the results of observation on the tensile strength, hardness, surface roughness, compressive residual stress and fatigue life of a shot peened Al6061-T651 were obtained. Experimental results show that arc height increase tremendously by shot velocity. Also, it shows that surface roughness, hardness, compressive residual stress and fatigue life increase as shot velocity increase.

Polycrystal Plasticity Modeling of Cyclic Residual Stress Relaxation in Shot Peened Martensitic Gear Steel

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
Rajesh Prasannavenkatesan ◽  
David L. McDowell
Keyword(s):  
Residual Stress ◽  
Stress Relaxation ◽  
Residual Stresses ◽  
Shot Peening ◽  
Cyclic Plasticity ◽  
Residual Stress Field ◽  
Residual Stress Relaxation ◽  
Gear Steel ◽  
Polycrystal Plasticity ◽  
Compressive Residual Stresses

Using a three-dimensional crystal plasticity model for cyclic deformation of lath martensitic steel, a simplified scheme is adopted to simulate the effects of shot peening on inducing initial compressive residual stresses. The model is utilized to investigate the subsequent cyclic relaxation of compressive residual stresses in shot peened lath martensitic gear steel in the high cycle fatigue (HCF) regime. A strategy is identified to model both shot peening and cyclic loading processes for polycrystalline ensembles. The relaxation of residual stress field during cyclic bending is analyzed for strain ratios Rε=0 and −1 for multiple realizations of polycrystalline microstructure. Cyclic microplasticity in favorably oriented martensite grains is the primary driver for the relaxation of residual stresses in HCF. For the case of Rε=−1, the cyclic plasticity occurs throughout the microstructure (macroplasticity) during the first loading cycle, resulting in substantial relaxation of compressive residual stresses at the surface and certain subsurface depths. The initial magnitude of residual stress is observed to influence the degree (percentage) of relaxation. Describing the differential intergranular yielding is necessary to capture the experimentally observed residual stress relaxation trends.

scholarly journals Influence of Residual Stress on Fatigue Design of AISI 304 Stainless Steel

2011 ◽  
Vol 7 (2) ◽  
pp. 44 ◽  
Author(s):  
L. Singh ◽  
R.A. Khan ◽  
M.L. Aggarwal
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Stainless Steel ◽  
Fatigue Strength ◽  
Stress Field ◽  
Shot Peening ◽  
Compressive Residual Stress ◽  
Residual Stress Field ◽  
Aisi 304 ◽  
Fatigue Design

 Austenitic stainless steel cannot be hardened by any form of heat treatment, in fact, quenching from 10000C merely softens them. They are usually cold worked to increase the hardness. Shot peening is a cold working process that changes micro-structure as well as residual stress in the surface layer. In the present work, the compressive residual stress and fatigue strength of AISI 304 austenitic stainless steel have been evaluated at various shot peening conditions. The improvement in various mechanical properties such as hardness, damping factors and fatigue strength was noticed. Compressive residual stress induced by shot peening varies with cyclic loading due to relaxation of compressive residual stress field. The consideration of relaxed compressive residual stress field instead of original compressive residual stress field provides reliable fatigue design of components. In this paper, the exact reductions in weight and control of mechanical properties due to shot peening process are discussed. 

Effect of shot peening coverage on residual stress field and surface roughness

2017 ◽  
Vol 34 (12) ◽  
pp. 938-945 ◽  
Author(s):  
Bin Qiang ◽  
Yadong Li ◽  
Changrong Yao ◽  
Xin Wang
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Stress Field ◽  
Shot Peening ◽  
Residual Stress Field

Numerical Simulation of Residual Stress Relaxation in Shot Peened High-Strength Aluminum Alloys Under Reverse Bending Fatigue

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
M. Benedetti ◽  
V. Fontanari ◽  
B. D. Monelli
Keyword(s):  
Residual Stress ◽  
Aluminum Alloys ◽  
Stress Relaxation ◽  
Stress Field ◽  
Shot Peening ◽  
High Strength ◽  
Fe Model ◽  
Residual Stress Field ◽  
Bending Fatigue ◽  
High Strength Aluminum Alloys

The mechanism of the residual stress relaxation during the fatigue life of shot peened high-strength aluminum alloys was investigated. Experiments were conducted on specimens subjected to three different shot peening treatments and tested under reverse bending fatigue. x-ray diffraction (XRD) measurements were carried out to determine the initial and stabilized residual stress fields. The residual stress field created by the surface treatments has been introduced into a finite element (FE) model by means of a fictitious temperature distribution. The elastic-plastic response of the superficial layers affected by the shot peening treatments has been derived through reverse strain axial testing combined with microhardness tests and implemented in the FE model. The proposed numerical/experimental approach is able to satisfactorily predict the residual stress field evolution. Notably, relaxation has been correctly simulated in the low-cycle fatigue regime and imputed to plastic flow in compression when the superposition of compressive residual and bending stresses exceeds the local cyclic yield strength of the material. Conversely, the residual stress field remains stable at load levels corresponding to the 5×106 cycles fatigue endurance.

The Numerical Optimization of Laser Shot Peening Parameters Based on Response Surface Analysis

2011 ◽  
Vol 464 ◽  
pp. 443-447
Author(s):  
Su Qing Jiang ◽  
Jian Hua Wu ◽  
Hong Guang Xu ◽  
Jian Zhong Zhou
Keyword(s):  
Residual Stress ◽  
Stress Field ◽  
Response Surface ◽  
Surface Analysis ◽  
Process Parameters ◽  
Shot Peening ◽  
Compressive Residual Stress ◽  
Response Surface Analysis ◽  
Residual Stress Field ◽  
Laser Process

Residual stress field induced by laser shot peening (LSP) was simulated using Box-Behnken experimental design. Compressive residual stress field intensity (S) was introduced to estimate the effect of compressive residual stress field on fatigue performance. The effect of laser process parameters (such as laser shock wave peak pressure, spot diameter and peening number) on S was analyzed by response surface analysis (RSA), quadratic regression predicting model for S was established, and the rationality of that was verified. Finally, the optimal combination of laser process parameters oriented to anti-fatigue manufacture was optimized. The results indicated statistical analysis results agreed well with those of simulation, RSA for parameter optimization of LSP is feasible.

scholarly journals Prediction of Residual Stress Relaxation of Shot Peened 2024-T351 Aluminum Alloy: Part 1

2011 ◽  
Vol 462-463 ◽  
pp. 1355-1360
Author(s):  
Omar Suliman Zaroog ◽  
Aidy Ali ◽  
Sahari B. Barkawi
Keyword(s):  
Residual Stress ◽  
Stress Relaxation ◽  
Shot Peening ◽  
Applied Load ◽  
Cold Work ◽  
Cyclic Tests ◽  
Initial State ◽  
Loading Cycle ◽  
Residual Stress Relaxation ◽  
Alloy Part

It is important to account for residual stress relaxation phenomenon in the design of the component. Specimens of 2024-T351 aluminium alloy were used in this study. The specimens were shot peened under three different shot peening intensities. Cyclic tests for two load magnitudes were performed for 1, 2, 10, 1000 and 10000 cycles. Residual stresses, microhardness and the cold work percentage were measured at initial state and after each loading cycle for the three shot peening intensities and for the two loads. The study revealed that most of the drop in the residual stress, microhardness and cold work happened in the first cycle are dependent on the applied load.

Sign in / Sign up

Export Citation Format

Share Document