scholarly journals An Experimental Study on the Precision Abrasive Machining Process of Hard and Brittle Materials with Ultraviolet-Resin Bond Diamond Abrasive Tools

Materials ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 125 ◽  
Author(s):  
Lei Guo ◽  
Xinrong Zhang ◽  
Shibin Chen ◽  
Jizhuang Hui
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Manufacturing Process ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Abrasive Machining ◽  
Machining Performance ◽  
Machined Surface ◽  
Ultraviolet Curable

Ultraviolet-curable resin was introduced as a bonding agent into the fabrication process of precision abrasive machining tools in this study, aiming to deliver a rapid, flexible, economical, and environment-friendly additive manufacturing process to replace the hot press and sintering process with thermal-curable resin. A laboratory manufacturing process was established to develop an ultraviolet-curable resin bond diamond lapping plate, the machining performance of which on the ceramic workpiece was examined through a series of comparative experiments with slurry-based iron plate lapping. The machined surface roughness and weight loss of the workpieces were periodically recorded to evaluate the surface finish quality and the material removal rate. The promising results in terms of a 12% improvement in surface roughness and 25% reduction in material removal rate were obtained from the ultraviolet-curable resin plate-involved lapping process. A summarized hypothesis was drawn to describe the dynamically-balanced state of the hybrid precision abrasive machining process integrated both the two-body and three-body abrasion mode.

scholarly journals A Comprehensive Study on Processing Ti–6Al–4V ELI with High Power EDM

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 303
Author(s):  
Panagiotis Karmiris-Obratański ◽  
Emmanouil L. Papazoglou ◽  
Beata Leszczyńska-Madej ◽  
Krzysztof Zagórski ◽  
Angelos P. Markopoulos
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
High Power ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
White Layer ◽  
Machining Process ◽  
Machining Parameters ◽  
Machining Performance

Electrical Discharge Machining (EDM) consists of a non-conventional machining process, which is widely used in modern industry, and especially in machining hard-to-cut materials. By employing EDM, complex shapes and geometries can be produced, with high dimensional accuracy. Titanium alloys, due to their unique inherent properties, are extensively utilized in high end applications. Nevertheless, they suffer from poor machinability, and thus, EDM is commonly employed for their machining. The current study presents an experimental investigation regarding the process of Ti–6Al–4V ELI with high power EDM, using a graphite electrode. Control parameters were the pulse-on current (Ip) and time (Ton), while Machining performances were estimated in terms of Material Removal Rate (MRR), Tool Material Removal Rate (TMRR), and Tool Wear Ratio (TWR). The machined Surface Roughness was calculated according to the Ra and the Rt values, by following the ISO 25178-2 standards. Furthermore, the EDMed surfaces were observed under optical and SEM microscopy, while their cross sections were also studied in order the Average White Layer Thickness (AWLT) and the Heat Affected Zone (HAZ) to be measured. Finally, for the aforementioned indexes, Analysis Of Variance was performed, whilst for the MRR and TMRR, based on the Response Surface Method (RSM), semi-empirical correlations were presented. The scope of the current paper is, through a series of experiments and by employing statistical tools, to present how two main machining parameters, i.e., pulse-on current and time, affect major machining performance indexes and the surface roughness.

High-Throughput Picosecond Laser Machining of Aerospace Nickel Superalloy

2021 ◽  
pp. 095440542110288
Author(s):  
Sundar Marimuthu ◽  
Bethan Smith
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Thermal Damage ◽  
Removal Rate ◽  
Picosecond Laser ◽  
Nickel Superalloy ◽  
Laser Machining ◽  
Process Conditions ◽  
Machining Performance

This manuscript discusses the experimental results on 300 W picosecond laser machining of aerospace-grade nickel superalloy. The effect of the laser’s energetic and beam scanning parameters on the machining performance has been studied in detail. The machining performance has been investigated in terms of surface roughness, sub-surface thermal damage, and material removal rate. At optimal process conditions, a picosecond laser with an average power output of 300 W can be used to achieve a material removal rate (MRR) of ∼140 mm3/min, with thermal damage less than 20 µm. Shorter laser pulse widths increase the material removal rate and reduce the resultant surface roughness. High scanning speeds improve the picosecond laser machining performance. Edge wall taper of ∼10° was observed over all the picosecond laser machined slots. The investigation demonstrates that high-power picosecond lasers can be used for the macro-machining of industrial components at an acceptable speed and quality.

Effect of Frequency to Ultrasonic Vibration-Assisted Wire-EDM

2019 ◽  
Vol 814 ◽  
pp. 127-131
Author(s):  
Patittar Nakwong ◽  
Apiwat Muttamara
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Electrical Discharge Machine ◽  
Machining Process ◽  
Wire Electrode ◽  
Ultrasonic Machine ◽  
Lower Amplitude ◽  
Wedm Process

Wire electrical discharge machine (WEDM) is non-conventional machining process. It can be used for hard cutting material. The study has been presented the combining WEDM with an ultrasonic machine (USM) with brass and tungsten were used as a wire electrode and workpiece respectively. The experiment was carried out with an ultrasonic transducer at 40, 80 kHz. The results were observed with the material removal rate (MRR) and surface roughness (Ra). This research introduced the method of USM setup and described the effected of vibration with the wire electrode on the displacement of amplitude. The result shows that the WEDM process with USM at 40 kHz can be more improved with the material removal rate and surface roughness than that of USM at 80 kHz. This can be explained that higher frequency affected to vibration displacement which makes lower amplitude.

Optimization of Process Parameters on Ti-6Al-4V Using Central Composite Design Method

2011 ◽  
Vol 189-193 ◽  
pp. 1393-1400 ◽  
Author(s):  
M.M. Rahman
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Peak Current ◽  
Long Pulse ◽  
Pulse On Time

Electrical discharge machining (EDM) is relatively modern machining process having distinct advantages over other machining processes and able to machine Ti-alloys effectively. This paper attempts to investigate the effects of process parameters on output response of titanium alloy Ti-6Al-4V in EDM utilizing copper tungsten as an electrode and positive polarity of the electrode. Mathematical models for material removal rate (MRR), electrode wear rate (EWR) and surface roughness (SR) are developed in this paper. Design of experiments method and response surface methodology techniques are implemented. The validity test of the fit and adequacy of the proposed models has been carried out through analysis of variance. It can be seen that as the peak current increases the TWR decreases till certain ampere and then increases. The excellent surface finish is investigated in this study at short pulse on time and in contrast the long pulse duration causes the lowest EWR. Long pulse off time provides minimum EWR and the impact of pulse interval on EWR depends on peak current. The result leads to wear rate of electrode and economical industrial machining by optimizing the input parameters. It found that the peak current, servo voltage and pulse on time are significant in material removal rate and surface roughness. Peak current has the greater impact on surface roughness and material removal rate.

scholarly journals Tool Wear Rate Prediction by using Optimization Techniques

2019 ◽  
Vol 9 (2) ◽  
pp. 1271-1277
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Optimization Techniques ◽  
Machining Process ◽  
Machining Parameters ◽  
Tungsten Carbides ◽  
Electro Discharge Machining ◽  
Pulse On Time

Electro discharge machining is a non-traditional machining process used for machining hard-to-machine materials, such as various grades of titanium alloys, heat-treated alloy steels, composites, tungsten carbides, and so forth. These materials are hard to machine with customary machining procedures like drilling, milling and hence electro-discharge machining is used to machine such materials to get better quality and efficiency. These materials are generally utilized in current industries like die making industries, aeronautics, nuclear industries, and medical fields. This type of machining is thermalbased, and machining takes place due to repetitive electric sparks that generate between workpiece and tool. Both tools and workpieces are inundated in a dielectric liquid, which has two primary functions. In the first place, it behaves like a medium between the work metal and the tool. Second, it is a flushing agent to expel the machined metal from the machined zone. Machining parameters like a pulse on time, current, wire feed the tool and gap voltage affect the output responses like surface roughness and material removal rate. The material removal rate is a significant parameter that determines machining efficiency. Surface roughness is also a vital parameter that decides machining quality. A lot of research has been conducted to determine the optimum parameters for obtaining the best results. In the present work, a comprehensive review of different types of EDM and the effect of various machining parameters on the surface roughness, material removal rate, and other response parameters has been done.

scholarly journals Multi-Objective Process Parameter Optimization for Surface Roughness and Material Removal Rate in Face Milling of Al 6061 T6 Alloy

2019 ◽  
Vol 9 (2) ◽  
pp. 137-142
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Feed Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Face Milling ◽  
Machining Process ◽  
Depth Of Cut ◽  
Al 6061

This study uses Taguchi methodology and Gray Relational Analysis approach to explore the optimization of face milling process parameters for Al 6061 T6 alloy.Surface Roughness (Ra), Material Removal Rate (MRR) has been identified as the objective of performance and productivity.The tests were performed by selecting cutting speed (mm / min), feed rate (mm / rev) and cutting depth (mm) at three settings on the basis of Taguchi's L9 orthogonal series.The grey relational approach was being used to establish a multiobjective relationship between both the parameters of machining and the characteristics of results. To find the optimum values of parameters in the milling operation, the response list and plots are used and found to be Vc2-f1-d3. To order to justify the optimum results, the confirmation tests are performed.The machining process parameters for milling were thus optimized in this research to achieve the combined goals such as low surface roughness and high material removal rate on Aluminum 6061 t6.It was concluded that depth of cut is the most influencing parameter followed by feed rate and cutting velocity.

Comparative evaluation of powder-mixed and ultrasonic-assisted rough die-sinking electrical discharge machining based on pulse characteristics

2019 ◽  
Vol 233 (14) ◽  
pp. 2515-2530 ◽  
Author(s):  
R Rajeswari ◽  
MS Shunmugam
Keyword(s):  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Graphite Powder ◽  
Machining Process ◽  
Machined Surface ◽  
Ultrasonic Assisted ◽  
Pulse On Time

Electrical discharge machining is used in the machining of complicated shapes in hardened molds and dies. In rough die-sinking stage, attempts are made to enhance material removal rate with a consequential reduction in cycle time. Powder mix and ultrasonic assistance are employed in the electrical discharge machining process to create gap conditions favoring material removal. In the present work, experiments are carried out on hardened D3 die steel using full-factorial design based on three levels of voltage, current and pulse on time. The gap phenomena in graphite powder-mixed and ultrasonic-assisted rough electrical discharge machining are studied using a detailed analysis of pulse shapes and their characteristic trains. Two new parameters, namely, energy expended over a second ( E) and performance factor ( PF) denoting the ratio of energy associated with sparks to total discharge energy, bring out gap conditions effectively. In comparison with the conventional electrical discharge machining for the selected condition, it is seen that the graphite powder mixed in the dielectric enhances the material removal rate by 20.8% with E of 215 J and PF of 0.227, while these values are 179.8 J and 0.076 for ultrasonic-assisted electrical discharge machining with marginal reduction of 3.9%. Cross-sectional images of workpieces also reveal the influence of electrical discharge machining conditions on the machined surface. The proposed approach can be extended to different powder mix and ultrasonic conditions to identify condition favoring higher material removal.

Effects of Process Parameters on Material Removal Rate and Surface Roughness in Wedm of H-13 Die Tool Steel

2018 ◽  
Vol 28 ◽  
pp. 55-66 ◽  
Author(s):  
Kuldeep Singh ◽  
Khushdeep Goyal ◽  
Deepak Kumar Goyal
Keyword(s):  
Surface Roughness ◽  
Taguchi Method ◽  
Tool Steel ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Pulse On Time ◽  
Pulse Off Time

In research work variation of cutting performance with pulse on time, pulse off time, wire type, and peak current were experimentally investigated in wire electric discharge machining (WEDM) process. Soft brass wire and zinc coated diffused wire with 0.25 mm diameter and Die tool steel H-13 with 155 mm× 70 mm×14 mm dimensions were used as tool and work materials in the experiments. Surface roughness and material removal rate (MRR) were considered as performance output in this study. Taguchi method was used for designing the experiments and optimal combination of WEDM parameters for proper machining of Die tool steel (H-13) to achieve better surface finish and material removal rate. In addition the most significant cutting parameter is determined by using analysis of variance (ANOVA). Keywords Machining, Process Parameters, Material removal rate, Surface roughness, Taguchi method

Statistical analysis of material removal rate and surface roughness in electrical discharge turning of titanium alloy (Ti-6Al-4V)

2016 ◽  
Vol 232 (9) ◽  
pp. 1603-1614 ◽  
Author(s):  
Vikas Gohil ◽  
Yogesh M Puri
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Machining Parameters ◽  
Peak Current ◽  
Pulse On Time

Electrical discharge turning is a unique form of electrical discharge machining process, which is being especially developed to generate cylindrical forms and helical profiles on the difficult-to-machine materials at both macro and micro levels. A precise submerged rotating spindle as a work holding system was designed and added to a conventional electrical discharge machine to rotate the workpiece. A conductive preshaped strip of copper as a forming tool is fed (reciprocate) continuously against the rotating workpiece; thus, mirror image of the tool is formed on the circumference of the workpiece. The machining performance of electrical discharge turning process is defined and influenced by its machining parameters, which directly affects the quality of the machined component. This study presents an investigation on the effects of the machining parameters, namely, pulse-on time, peak current, gap voltage, spindle speed and flushing pressure, on the material removal rate (MRR) and surface roughness (Ra) in electrical discharge turning of titanium alloy Ti-6Al-4V. This has been done by means of Taguchi’s design of experiment technique. Analysis of variance as well as regression analysis is performed on the experimental data. The signal-to-noise ratio analysis is employed to find the optimal condition. The experimental results indicate that peak current, gap voltage and pulse-on time are the most significant influencing parameters that contribute more than 90% to material removal rate. In the context of Ra, peak current and pulse-on time come up with more than 82% of contribution. Finally, the obtained predicted optimal results were verified experimentally. It was shown that the error values are all less than 6%, confirming the feasibility and effectiveness of the adopted approach.

Investigation into Chemo-Mechanical Fixed Abrasive Polishing of Fused Silica with the Assistance of Ultrasonic Vibration

2012 ◽  
Vol 523-524 ◽  
pp. 155-160 ◽  
Author(s):  
Ya Guo Li ◽  
Yong Bo Wu ◽  
Li Bo Zhou ◽  
Hui Ru Guo ◽  
Jian Guo Cao ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Material Removal ◽  
Optical Glass ◽  
Removal Rate ◽  
Fused Silica ◽  
Processing Efficiency ◽  
Machined Surface ◽  
Fixed Abrasive

Ultrasonic vibration assisted processing is well known for the improvement in machined surface quality and processing efficiency due to the reduced forces and tribology-generated heating when grinding hard-brittle materials. We transplanted this philosophy to chemo-mechanical fixed abrasive polishing of optical glass, namely fused silica, in an attempt to improve surface roughness and/or material removal rate. Experiments were conducted to elucidate the fundamental characteristics of chemo-mechanical fixed abrasive polishing of fused silica in the presence and absence of ultrasonic vibration on a setup with an in-house built gadget. The experimental results show that ultrasonic vibration assisted chemo-mechanical fixed abrasive polishing can yield increased material removal rate while maintaining the surface roughness of manufactured optics compared to conventional fixed abrasive polishing without ultrasonic vibration. The mechanism of material removal in fixed abrasive polishing was also delved. We found that the glass material is removed through the synergic effects of chemical and mechanical actions between abrasives and glass and the resultant grinding swarf contains ample Si element as well as Ce element, standing in stark contrast to the polisher that contains abundant Ce element and minor Si element.

Sign in / Sign up

Export Citation Format

Share Document