High-Throughput Picosecond Laser Machining of Aerospace Nickel Superalloy

2021 ◽  
pp. 095440542110288
Author(s):  
Sundar Marimuthu ◽  
Bethan Smith
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Thermal Damage ◽  
Removal Rate ◽  
Picosecond Laser ◽  
Nickel Superalloy ◽  
Laser Machining ◽  
Process Conditions ◽  
Machining Performance

This manuscript discusses the experimental results on 300 W picosecond laser machining of aerospace-grade nickel superalloy. The effect of the laser’s energetic and beam scanning parameters on the machining performance has been studied in detail. The machining performance has been investigated in terms of surface roughness, sub-surface thermal damage, and material removal rate. At optimal process conditions, a picosecond laser with an average power output of 300 W can be used to achieve a material removal rate (MRR) of ∼140 mm3/min, with thermal damage less than 20 µm. Shorter laser pulse widths increase the material removal rate and reduce the resultant surface roughness. High scanning speeds improve the picosecond laser machining performance. Edge wall taper of ∼10° was observed over all the picosecond laser machined slots. The investigation demonstrates that high-power picosecond lasers can be used for the macro-machining of industrial components at an acceptable speed and quality.

Grinding of Chromium Carbide Coatings Using Electroplated Diamond Wheels

2017 ◽  
Vol 139 (12) ◽  
Author(s):  
Zhongde Shi ◽  
Amr Elfizy ◽  
Helmi Attia ◽  
Gilbert Ouellet
Keyword(s):  
Surface Roughness ◽  
Chromium Carbide ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Depth Of Cut ◽  
Process Conditions ◽  
Carbide Coatings ◽  
Grinding Power ◽  
Chromium Carbide Coatings

This paper reports an experimental study on grinding of chromium carbide coatings using electroplated diamond wheels. The work was motivated by machining carbide coatings in gas turbine engine applications. The objective is to explore the process conditions and parameters satisfying the ground surface quality requirements. Surface grinding experiments were conducted with water-based grinding fluid on chromium carbide coated on flat surfaces of aluminum blocks for rough grinding at a fixed wheel speed vs = 30 m/s, and finish grinding at vs = 30, 60 m/s. The effects of depth of cut and workspeed on grinding power, forces, and surface roughness were investigated for each of the wheel speeds. Material removal rate Q = 20 mm3/s for rough grinding at a grinding width b = 101.6 mm was achieved. It was found that the maximum material removal rate achievable in rough grinding was restricted by chatters, which was mainly due to the large grinding width. The specific energy ranged from 27 to 59 J/mm3 under the tested conditions. Surface roughness Ra = 3.5–3.8 μm were obtained for rough grinding, while Ra = 0.6–1.5 μm were achieved for finish grinding. Surface roughness was not sensitive to grinding parameters under the tested conditions, but was strongly dependent on the diamond grain sizes. Imposing axial wheel oscillations to the grinding motions reduced surface roughness by about 60% under the tested condition. It was proved that it is feasible to grind the chromium carbide coating with electroplated diamond wheels.

scholarly journals An Experimental Study on the Precision Abrasive Machining Process of Hard and Brittle Materials with Ultraviolet-Resin Bond Diamond Abrasive Tools

Materials ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 125 ◽  
Author(s):  
Lei Guo ◽  
Xinrong Zhang ◽  
Shibin Chen ◽  
Jizhuang Hui
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Manufacturing Process ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Abrasive Machining ◽  
Machining Performance ◽  
Machined Surface ◽  
Ultraviolet Curable

Ultraviolet-curable resin was introduced as a bonding agent into the fabrication process of precision abrasive machining tools in this study, aiming to deliver a rapid, flexible, economical, and environment-friendly additive manufacturing process to replace the hot press and sintering process with thermal-curable resin. A laboratory manufacturing process was established to develop an ultraviolet-curable resin bond diamond lapping plate, the machining performance of which on the ceramic workpiece was examined through a series of comparative experiments with slurry-based iron plate lapping. The machined surface roughness and weight loss of the workpieces were periodically recorded to evaluate the surface finish quality and the material removal rate. The promising results in terms of a 12% improvement in surface roughness and 25% reduction in material removal rate were obtained from the ultraviolet-curable resin plate-involved lapping process. A summarized hypothesis was drawn to describe the dynamically-balanced state of the hybrid precision abrasive machining process integrated both the two-body and three-body abrasion mode.

scholarly journals Prediction of Surface Roughness and Material Removal Rate in Electrochemical Machining Using Taguchi Method

2017 ◽  
Vol 12 (4) ◽  
pp. 72-80 ◽  
Author(s):  
Abbas Fadhil Ibrahim
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrolyte Concentration ◽  
Removal Rate ◽  
Electrochemical Machining ◽  
Maintenance Cost ◽  
Process Conditions ◽  
Machining Parameters

Electrochemical machining is one of the widely used non-conventional machining processes to machine complex and difficult shapes for electrically conducting materials, such as super alloys, Ti-alloys, alloy steel, tool steel and stainless steel.  Use of optimal ECM process conditions can significantly reduce the ECM operating, tooling, and maintenance cost and can produce components with higher accuracy. This paper studies the effect of process parameters on surface roughness (Ra) and material removal rate (MRR), and the optimization of process conditions in ECM. Experiments were conducted based on Taguchi’s L9 orthogonal array (OA) with three process parameters viz. current, electrolyte concentration, and inter-electrode gap. Signal-to-noise (S/N), the analysis of variance (ANOVA) was employed to find the optimal levels and to analyze the effect of electrochemical machining parameters on Ra and MRR. The surface roughness of the workpiece was decreased with the increase in current values and electrolyte concentration while causing an increase in material removal rate. The ability of the independent values to predict the dependent values (R2) were 87.5% and 96.3% for mean surface roughness and material removal rate, respectively.

scholarly journals A Comprehensive Study on Processing Ti–6Al–4V ELI with High Power EDM

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 303
Author(s):  
Panagiotis Karmiris-Obratański ◽  
Emmanouil L. Papazoglou ◽  
Beata Leszczyńska-Madej ◽  
Krzysztof Zagórski ◽  
Angelos P. Markopoulos
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
High Power ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
White Layer ◽  
Machining Process ◽  
Machining Parameters ◽  
Machining Performance

Electrical Discharge Machining (EDM) consists of a non-conventional machining process, which is widely used in modern industry, and especially in machining hard-to-cut materials. By employing EDM, complex shapes and geometries can be produced, with high dimensional accuracy. Titanium alloys, due to their unique inherent properties, are extensively utilized in high end applications. Nevertheless, they suffer from poor machinability, and thus, EDM is commonly employed for their machining. The current study presents an experimental investigation regarding the process of Ti–6Al–4V ELI with high power EDM, using a graphite electrode. Control parameters were the pulse-on current (Ip) and time (Ton), while Machining performances were estimated in terms of Material Removal Rate (MRR), Tool Material Removal Rate (TMRR), and Tool Wear Ratio (TWR). The machined Surface Roughness was calculated according to the Ra and the Rt values, by following the ISO 25178-2 standards. Furthermore, the EDMed surfaces were observed under optical and SEM microscopy, while their cross sections were also studied in order the Average White Layer Thickness (AWLT) and the Heat Affected Zone (HAZ) to be measured. Finally, for the aforementioned indexes, Analysis Of Variance was performed, whilst for the MRR and TMRR, based on the Response Surface Method (RSM), semi-empirical correlations were presented. The scope of the current paper is, through a series of experiments and by employing statistical tools, to present how two main machining parameters, i.e., pulse-on current and time, affect major machining performance indexes and the surface roughness.

Effects of Process Parameters on Surface Roughness and MRR in the hard turning of EN 36 steel

2018 ◽  
pp. 102-110
Author(s):  
Amritpal Singh ◽  
Rakesh Kumar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Hard Turning ◽  
Control Parameter ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting

In the present study, Experimental investigation of the effects of various cutting parameters on the response parameters in the hard turning of EN36 steel under the dry cutting condition is done. The input control parameters selected for the present work was the cutting speed, feed and depth of cut. The objective of the present work is to minimize the surface roughness to obtain better surface finish and maximization of material removal rate for better productivity. The design of experiments was done with the help of Taguchi L9 orthogonal array. Analysis of variance (ANOVA) was used to find out the significance of the input parameters on the response parameters. Percentage contribution for each control parameter was calculated using ANOVA with 95 % confidence value. From results, it was observed that feed is the most significant factor for surface roughness and the depth of cut is the most significant control parameter for Material removal rate.

Effect of SiC-Cu Electrode on Material Removal Rate, Tool Wear and Surface Roughness in EDM Process

2020 ◽  
Vol 38 (9A) ◽  
pp. 1406-1413
Author(s):  
Yousif Q. Laibia ◽  
Saad K. Shather
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
304 Stainless Steel ◽  
Tool Electrode ◽  
Pulse Time ◽  
Edm Process

Electrical discharge machining (EDM) is one of the most common non-traditional processes for the manufacture of high precision parts and complex shapes. The EDM process depends on the heat energy between the work material and the tool electrode. This study focused on the material removal rate (MRR), the surface roughness, and tool wear in a 304 stainless steel EDM. The composite electrode consisted of copper (Cu) and silicon carbide (SiC). The current effects imposed on the working material, as well as the pulses that change over time during the experiment. When the current used is (8, 5, 3, 2, 1.5) A, the pulse time used is (12, 25) μs and the size of the space used is (1) mm. Optimum surface roughness under a current of 1.5 A and the pulse time of 25 μs with a maximum MRR of 8 A and the pulse duration of 25 μs.

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

Sign in / Sign up

Export Citation Format

Share Document