scholarly journals Study of the Self-Healing Performance of Semi-Flexible Pavement Materials Grouted with Engineered Cementitious Composites Mortar based on a Non-Standard Test

Materials ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 3488 ◽  
Author(s):  
Cai ◽  
Huang ◽  
Wu
Keyword(s):  
Flexural Strength ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Flexible Pavement ◽  
Standard Test ◽  
The Self ◽  
Cementitious Composites ◽  
Self Healing ◽  
High Temperature Stability ◽  
Engineered Cementitious Composites

Semi-flexible pavement (SFP) materials, with their characteristics of good high temperature stability, strong durability, and lower cost, are suitable for heavy-duty roads, but their cracking problem has hindered the development and popularization of this kind of pavement to a certain extent. In this study, engineered cementitious composites (ECC) were used to form ECC-SFP materials. The self-healing properties of ECC-SFP materials with three kinds of voids of matrix asphalt mixtures were studied. The test results showed that the fluidity and strength of the ECC mortars met the specification requirements when the water–cement ratio was 0.23 and the ECC fiber dosage was 1–2%. The flexural strength of ECC mortar is better than that of ordinary mortar. The higher the ECC fiber dosage, the higher the flexural strength. Increasing the void of the matrix asphalt mixture and the amount of ECC mortar increased the toughness of the ECC-SFP material, which was seen as an increase of the flow value. Curing conditions are key factor affecting the self-healing properties of ECC mortar and ECC-SFP materials. The self-healing effect of materials in 60 °C water is the best. When an ECC fiber dosage of 1% was used, the HImor of ECC mortar and HImix of ECC-SFP material were 27.5% and 24.8%, respectively. With the addition of ECC material, ECC-SFP material achieved a certain degree of self-healing, but this still needs to be further optimized. Studies of grouting process optimization and increasing the ECC fiber dosage are feasible directions to explore in order to improve the self-healing properties of ECC-SFP materials in the future.

scholarly journals Microwave Absorption Ability of Steel Slag and Road Performance of Asphalt Mixtures Incorporating Steel Slag

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 663 ◽  
Author(s):  
Baowen Lou ◽  
Zhuangzhuang Liu ◽  
Aimin Sha ◽  
Meng Jia ◽  
Yupeng Li
Keyword(s):  
Microwave Absorption ◽  
Steel Slag ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Asphalt Mixtures ◽  
Microwave Absorber ◽  
Self Healing ◽  
High Temperature Stability ◽  
Road Performance ◽  
On The Road

Excessive usage of non-renewable natural resources and massive construction wastes put pressure on the environment. Steel slags, the main waste material from the metal industry, are normally added in asphalt concrete to replace traditional aggregate. In addition, as a typical microwave absorber, steel slag has the potential to transfer microwave energy into heat, thus increasing the limited self-healing ability of asphalt mixture. This paper aims to investigate the microwave absorption potentials of steel slag and the effect of its addition on road performance. The magnetic parameters obtained from a microwave vector network analyzer were used to estimate the potential use of steel slag as microwave absorber to heal cracks. Meanwhile, the initial self-healing temperature was further discussed according to the frequency sweeping results. The obvious porous structure of steel slag observed using scanning electron microscopy (SEM) had important impacts on the road performance of asphalt mixtures. Steel slag presented a worse effect on low-temperature crack resistance and water stability, while high-temperature stability can be remarkably enhanced when the substitution of steel slag was 60% by volume with the particle size of 4.75–9.5 mm. Overall, the sustainability of asphalt mixtures incorporating steel slag can be promoted due to its excellent mechanical and microwave absorption properties.

The Performance Analysis of Semi-Flexible Pavement by the Volume Parameter of Matrix Asphalt Mixture

2010 ◽  
Vol 168-170 ◽  
pp. 351-356 ◽  
Author(s):  
Qing Jun Ding ◽  
Zheng Sun ◽  
Fan Shen ◽  
Shao Long Huang
Keyword(s):  
Pore Structure ◽  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Flexible Pavement ◽  
High Temperature Stability ◽  
Important Target ◽  
Air Void ◽  
Better Than ◽  
Pavement Material

The volume parameter of matrix asphalt mixture is an important target in the design of the semi-flexible pavement. The research used volume-standar to design four kinds of matrix asphalt mixture, fulfilled mechanics performances and performances of semi-flexible pavement material with different aging, compared with common asphalt mixture and researched the effect by air void and pore structure. It proves that the compacted intensity, high-temperature stability and low temperature bend of the semi-flexible pavement material is better than common asphalt pavement material, the performances of matrix asphalt mixture with high air void is better. As for matrix asphalt mixture with same air void but different pore structure, the performances of homogenous grade design is prior to consecutive grade disign.

Experimental Study of Typical Graded Asphalt Mixture about Dynamic Stability at High Temperature

2016 ◽  
Vol 858 ◽  
pp. 300-304
Author(s):  
Zhen Fu Chen ◽  
Dan Wu ◽  
Qiu Wang Tao ◽  
Yuan Chu Gan
Keyword(s):  
Experimental Data ◽  
Experimental Study ◽  
High Temperature ◽  
Asphalt Mixture ◽  
Temperature Stability ◽  
Specimen Thickness ◽  
High Temperature Stability ◽  
Change Trend ◽  
Comparison And Analysis ◽  
The Stability

The high temperature stability of AC-16, AC-13, AC-20 under specimen thickness of 5cm and 6cm is studied through indoor asphalt mixture high rutting test, Through comparison and analysis about experimental data, it is found that the stability of AC-16, AC-13, AC-20 asphalt mixture at high- temperature decreases in turn. It is shown that thickness changes did not affect the change trend of the high temperature stability under gradation change, and the stability of AC-16 at high-temperature is the best, the AC-13 is second and the AC-20 is less.

Sign in / Sign up

Export Citation Format

Share Document