scholarly journals Study on the Flexural Performance of Hybrid-Reinforced Concrete Beams with a New Cathodic Protection System Subjected to Corrosion

Materials ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 234 ◽  
Author(s):  
Yingwu Zhou ◽  
Yaowei Zheng ◽  
Lili Sui ◽  
Biao Hu ◽  
Xiaoxu Huang
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Steel Corrosion ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Flexural Performance ◽  
Reinforced Polymer ◽  
Steel Bar

Steel corrosion is considered as the main factor for the insufficient durability of concrete structures, especially in the marine environment. In this paper, to further inhibit steel corrosion in a high chloride environment and take advantage of the dual-functional carbon fiber reinforced polymer (CFRP), the impressed current cathodic protection (ICCP) technique was applied to the hybrid-reinforced concrete beam with internally embedded CFRP bars and steel fiber reinforced polymer composite bar (SFCB) as the anode material while the steel bar was compelled to the cathode. The effect of the new ICCP system on the flexural performance of the hybrid-reinforced concrete beam subjected to corrosion was verified experimentally. First, the electricity-accelerated precorrosion test was performed for the steel bar in the hybrid-reinforced beams with a target corrosion ratio of 5%. Then, the dry–wet cycles corrosion was conducted and the ICCP system was activated simultaneously for the hybrid-reinforced concrete beam for 180 days. Finally, the three-point bending experiment was carried out for the hybrid-reinforced concrete beams. The steel bars were taken out from the concrete to quantitatively measure the corrosion ratio after flexural tests. Results showed that the further corrosion of steel bars could be inhibited effectively by the ICCP treatment with the CFRP bar and the SFCB as the anode. Additionally, the ICCP system showed an obvious effect on the flexural behavior of the hybrid-reinforced concrete beams: The crack load and ultimate load, as well as the stiffness, were enhanced notably compared with the beam without ICCP treatment. Compared with the SFCB anode, the ICCP system with the CFRP bar as the anode material was more effective for the hybrid-reinforced concrete beam to prevent the steel corrosion.

Numerical Analysis of Reinforced Concrete Beam Strengthened with CFRP or GFRP Laminates

2016 ◽  
Vol 707 ◽  
pp. 51-59 ◽  
Author(s):  
Osama Ahmed Mohamed ◽  
Rania Khattab
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

The behaviour of reinforced concrete beam strengthened with Carbon Fiber Reinforced Polymer (CFRP) and Glass fiber reinforced polymer GFRP laminates was investigated using finite element models and the results are presented in this paper. The numerical investigation assessed the effect of the configuration of FRP strengthening laminates on the behaviour of concrete beams. The load-deflection behaviour, and ultimate load of strengthened beam were compared to those of un-strengthened concrete beams. It was shown that using U-shaped FRP sheets increased the ultimate load. The stiffness of the strengthed beam also increased after first yielding of steel reinforcing bars. At was also observed that strengthening beams with FRP laminates to one-fourth of the beam span, modifies the failure of the beam from shear-controlled near the end of the unstrengthened beam, to flexure-controlled near mid-span. CFRP produced better results compared GFRP in terms of the ability to enhance the behavior of strengthenened reinforced concrete beams.

scholarly journals Flexural performance of reinforced concrete beams made with locally sourced fly ash

2021 ◽  
Vol 15 (2) ◽  
pp. 38-50
Author(s):  
Nguyen Van Chinh
Keyword(s):  
Reinforced Concrete ◽  
Fly Ash ◽  
Portland Cement ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Flexural Performance ◽  
Steel Bars ◽  
Cracking Pattern

The paper investigates the flexural performance of reinforced concrete beams in which fly ash from Vinh Tan power station was used to replace original Portland cement in the proportions of 0%, 10%, 20% and 40% by weight. Twelve reinforced concrete beams with the dimensions of 100×150 mm in cross section and 1000 mm in length were cast and cured in water. These beams were flexurally tested under 4 points bending at 28 days, 56 days and 90 days. Load deflection curves, first cracking load, yielding of steel bars, ultimate load, and cracking pattern of the reinforced concrete beams are used to investigate the performance of the control and fly ash beams at 28 days, 56 days and 90 days. The results show that locally sourced fly ash does not affect the load and deflection curves. Fly ash reduced slightly the flexural strength of reinforced concrete beams at 90 days when 40% of fly ash was used to replaced Portland cement. Keywords: fly ash; reinforced concrete beam; flexural performance; load; deflection.

Experimental Research on Flexural Behavior of FRP-Reinforced Concrete Beams

2011 ◽  
Vol 250-253 ◽  
pp. 1478-1482
Author(s):  
Zhi Juan Sun ◽  
Chao He Chen ◽  
Ming Jin Chu ◽  
Peng Feng
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Design Method ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Flexural Behavior ◽  
Concrete Member ◽  
Reinforced Polymer ◽  
Reinforced Concrete Member

In order to improve the durability of reinforced concrete member, fiber reinforced polymer (FRP)-reinforced concrete member is introduces. Monotonic loading was applied to a reinforced concrete beam and FRP-reinforced concrete beam, in order to investigate the failure progress and characteristics of FRP-reinforced concrete beam.. The presenting study provide a basis for improving the design method for FRP-reinforced concrete member.

Simulation Behavior of Flexure in Reinforced Concrete Beam with Opening Reinforced with Glass Fiber Reinforced Polymer (GFRP)

2016 ◽  
Vol 857 ◽  
pp. 421-425
Author(s):  
Saif M. Thabet ◽  
S.A. Osman
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Glass Fiber ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

This paper presents an investigation into the flexural behaviour of reinforced concrete beam with opening reinforced with two different materials i.e., steel and Glass Fiber Reinforced Polymer (GFRP). Comparison study between the two different materials were carried out and presented in this study through non-linear Finite Element Method (FEM) using the commercial ABAQUS 6.10 software package. The performance of the opening beam reinforced with GFRP is influenced by several key parameters. Simulation analyses were carried out to determine the behavior of beam with opening subjected to monotonic loading. The main parameters considered in this study are size of opening and reinforcement diameter. The results show that GFRP give 23%-29% more ductility than steel reinforcement. The result also shows when the size of opening change from 200mm to 150mm or from 150mm to 100mm the ultimate load capacity increase by 15%. In general, good agreement between the Finite Element (FE) simulation and the available experimental result has been obtained.

scholarly journals Influence of steel–concrete bond damage on the dynamic stiffness of cracked reinforced concrete beams

2018 ◽  
Vol 21 (13) ◽  
pp. 1977-1989 ◽  
Author(s):  
Tengfei Xu ◽  
Jiantao Huang ◽  
Arnaud Castel ◽  
Renda Zhao ◽  
Cheng Yang
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Natural Frequencies ◽  
Concrete Beams ◽  
Dynamic Stiffness ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Reinforcing Bar ◽  
Sustained Loading ◽  
Inertia Model

In this article, experiments focusing at the influence of steel–concrete bond damage on the dynamic stiffness of cracked reinforced concrete beams are reported. In these experiments, the bond between concrete and reinforcing bar was damaged using appreciate flexural loads. The static stiffness of cracked reinforced concrete beam was assessed using the measured load–deflection response under cycles of loading and unloading, and the dynamic stiffness was analyzed using the measured natural frequencies with and without sustained loading. Average moment of inertia model (Castel et al. model) for cracked reinforced beams by taking into account the respective effect of bending cracks (primary cracks) and the steel–concrete bond damage (interfacial microcracks) was adopted to calculate the static load–deflection response and the natural frequencies of the tested beams. The experimental results and the comparison between measured and calculated natural frequencies show that localized steel–concrete bond damage does not influence remarkably the dynamic stiffness and the natural frequencies both with and without sustained loading applied. Castel et al. model can be used to calculate the dynamic stiffness of cracked reinforced concrete beam by neglecting the effect of interfacial microcracks.

Prediction Scheme of Torsional Strength of Reinforced Concrete Beam

2012 ◽  
Vol 214 ◽  
pp. 306-310
Author(s):  
Han Chen Huang
Keyword(s):  
Genetic Algorithm ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Ann Model ◽  
Torsional Strength ◽  
Prediction Scheme ◽  
Optimal Network

This study proposes a artificial neural network with genetic algorithm (GA-ANN) for predicting the torsional strength of reinforced concrete beam. Genetic algorithm is used to the optimal network structure and parameters. A database of the torsional failure of reinforced concrete beams with a rectangular section subjected to pure torsion was obtained from existing literature for analysis. This study compare the predictions of the GA-ANN model with the ACI 318 code used for analyzing the torsional strength of reinforced concrete beam. The results show that the proposed model provides reasonable predictions of the ultimate torsional strength of reinforced concrete beams and offers superior torsion accuracy compared to that of the ACI 318-89 equation.

Uniform loading on the reinforced concrete beam produced by the specific cylinder-shaped rubber bags fully filled with air or water

2020 ◽  
Vol 23 (9) ◽  
pp. 1934-1947
Author(s):  
Dapeng Chen ◽  
Li Chen ◽  
Qin Fang ◽  
Yuzhou Zheng ◽  
Teng Pan
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Element Model ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Uniform Loading ◽  
Air Bag

The bending behavior of reinforced concrete beams under uniform pressure is critical for the research of the blast-resistance performance of structural components under explosive loads. In this study, a bending test of five reinforced concrete beams with the dimensions of 200 mm (width) × 200 mm (depth) × 2500 mm (length) under uniform load produced by a specific cylinder-shaped rubber bag filled with air or water was conducted to investigate their flexural performances. An air bag load was applied to three of the reinforced concrete beams, a water bag load was applied to one reinforced concrete beam, and the remainder beam was subjected to the 4-point bending load. The experimental results highlighted that the air bag and water bag loading methods can be used to effectively apply uniform loads to reinforced concrete beams. Moreover, the stiffness of the air bag was improved by 123% in accordance with the initial pressure increases from 0.15 to 0.45 MPa. In addition, a finite element model of the test loading system was established using ABAQUS/Standard software. Moreover, the critical factors of the air bag loading method were analyzed using the numerical model. The calculated results were found to be in good agreement with the test data. The established finite element model can therefore be used to accurately simulate the action performances of the uniform loading technique using rubber bags filled with air or water.

Sign in / Sign up

Export Citation Format

Share Document