scholarly journals Microchannel Liquid-Cooled Heat Exchanger Based on a Nonuniform Lattice: Study on Structure Calculation, Formation Process, and Boiling Heat Transfer Performance

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7248
Author(s):  
Bo Qian ◽  
Hongri Fan ◽  
Gang Liu ◽  
Jianrui Zhang ◽  
Pei Li
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boiling Heat Transfer ◽  
Heat Flux Density ◽  
Heat Transfer Performance ◽  
Lattice Structure ◽  
Flow Density ◽  
Transfer Performance ◽  
Heat Flow Density ◽  
Uniform Frames

A microchannel radiator is advantageous due to its high efficiency and large boiling heat transfer coefficient of two-phase flow. Based on the research of uniform lattice structures, this study proposed a microchannel heat exchanger with a nonuniform lattice structure. The calculation, optimal formation, and boiling heat transfer performance of the nonuniform lattice structure based on selective laser melting (SLM) were investigated, and heat exchange samples were successfully prepared using SLM. The porosity and pore morphology of the samples were analysed, and the contrast experiments of boiling heat transfer were conducted with deionised water. The results revealed that the heat flow density of the lattice structure was a minimum of 244% higher than that of the traditional liquid-cooled plate. The critical heat flux density of the lattice structure is 110 W∙cm−2, and the critical heat flux density of the traditional flat plate is 45 W∙cm−2. In addition, the effects of cell structures indicated that for frame cells, the heat transfer effect of nonuniform frames was inferior to that of uniform frames; for face-centred cubic (FCC) cells, the nonuniform and uniform frames exhibited the same trend. However, the heat flow density of FCC cells was 25% higher than that of frame structures.

An Experimental Investigation of Boiling Heat Transfer of Fluorocarbon R-11 Refrigerant for Concentric-Tube Thermosyphon

1981 ◽  
Vol 103 (3) ◽  
pp. 472-477 ◽  
Author(s):  
N. Seki ◽  
S. Fukusako ◽  
K. Koguchi
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Experimental Investigation ◽  
Free Convection ◽  
Boiling Heat Transfer ◽  
Void Ratio ◽  
Heat Transfer Performance ◽  
Transfer Performance ◽  
Total Heat Flux ◽  
Controlling Variables

The characteristics of the boiling heat transfer for a concentric-tube open thermosyphon are examined in detail. Fluorocarbon R-11 refrigerant as a testing fluid is utilized. Out of a number of possible controlling variables, the effects of the heat flux, the void ratio, and the diametric ratio of the concentric-tube on the heat-transfer performance are determined. From the present experimental results it is demonstrated that total heat flux can be appropriately predicted by a superposition of the heat flux due to the available correlations for free convection and due to the correlations experimentally determined for boiling heat flux.

Nanofluid Boiling Heat Transfer and Critical Heat Flux Enhancement: Mechanism to Be Revealed

2013 ◽  
Author(s):  
Junmei Wu ◽  
Jiyun Zhao ◽  
Yun Wang
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Heat Transfer Performance ◽  
Bubble Dynamics ◽  
High Heat ◽  
Solid Particles ◽  
High Heat Flux ◽  
Transfer Performance

As a novel strategy to improve heat transfer characteristics of fluids by the addition of solid particles with diameters below 100 nm, nanofluids exhibits unprecedented heat transfer properties and are being considered as potential working fluids to be used in high heat flux systems such as nuclear reactors, electronic cooling systems and solar collectors. The present paper reviews the state-of-the-art studies on nanofluid boiling heat transfer performance and critical heat flux (CHF) enhancement. It is found that some results on nanofluids boiling heat transfer performance are inconsistent or contradictory in data published. The knowledge on the mechanism of nanofluids boiling CHF enhancement is insufficient. Bubble dynamics of nanofluids boiling is suggested to be investigated to identify the exact contributions of solid surface modifications and suspended nanoparticles to CHF enhancement in nanofluids boiling heat transfer.

Experimental and Mechanism Investigation on Boiling Heat Transfer Characteristics of Alumina/Water Nanofluid on a Cylindrical Tube

NANO ◽  
2019 ◽  
Vol 14 (10) ◽  
pp. 1950124
Author(s):  
Hao Zhang ◽  
Zeng-en Li ◽  
Shan Qing ◽  
Zhuangzhuang Jia ◽  
Jiarui Xu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Particle Deposition ◽  
Heat Transfer Performance ◽  
Pool Boiling ◽  
Heating Surface ◽  
Cylindrical Tube ◽  
Influential Factors ◽  
Transfer Performance ◽  
Pool Boiling Heat Transfer

Nucleate pool boiling heat transfer experiments have been conducted to nanofluids on a horizontal cylinder tube under atmospheric pressure. The nanofluids are prepared by dispersing Al2O3 nanoparticles into distilled water at concentrations of 0.001, 0.01, 0.1, 1 and 2[Formula: see text]wt.% with or without sodium, 4-dodecylbenzenesulfonate (SDBS). The experimental results showed that: nanofluids at lower concentrations (0.001[Formula: see text]wt.% to 1[Formula: see text]wt.%) can obviously enhance the pool boiling heat transfer performance, but signs of deterioration can be observed at higher concentration (2[Formula: see text]wt.%). The presence of SDBS can obviously enhance the pool boiling heat transfer performance, and with the presence of SDBS, a maximum enhancement ratio of BHTC of 69.88%, and a maximum decrease ratio of super heat of 41.12% can be found in Group NS5 and NS4, respectively. The tube diameter and wall thickness of heating surface are the influential factors for boiling heat transfer coefficient. Besides, we find that Rohsenow formula failed to predict the characteristics of nanofluids. The mechanism study shows that: the decrease of surface tension, which leads to the decrease of bubble departure diameter, and the presence of agglomerates in nanofluids are the reasons for the enhanced pool boiling heat transfer performance. At higher concentration, particle deposition will lead to the decrease of distribution density of the vaporization core, and as a result of that, the boiling heat transfer performance will deteriorate.

Convective Heat Transfer Performance of FC-72 in a Pin-Finned Channel

2008 ◽  
Author(s):  
Liang-Han Chien ◽  
S.-Y. Pei ◽  
T.-Y. Wu
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Flow Rate ◽  
Smooth Surface ◽  
Heat Transfer Performance ◽  
Fluid Temperature ◽  
Transfer Performance ◽  
Finned Surface

This study investigates the influence of the heat flux and mass velocity on convective heat transfer performance of FC-72 in a rectangular channel of 20mm in width and 2 mm in height. The heated side has either a smooth surface or a pin-finned surface. The inlet fluid temperature is maintained at 30°C. The total length of the test channel is 113 mm, with a heated length of 25mm. The flow rate varies between 80 and 960 ml/min, and the heat flux sets between 18 and 50 W/cm2. The experimental results show that the controlling variable is heat flux instead of flow rate because of the boiling activities in FC-72. At a fixed flow rate, the pin-finned surface yields up to 20% higher heat transfer coefficient and greater critical heat flux than those of a smooth surface.

A Study on Flow Boiling in Microchannel With Piranha Pin Fin

2015 ◽  
Author(s):  
X. Yu ◽  
C. Woodcock ◽  
Y. Wang ◽  
J. Plawsky ◽  
Y. Peles
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Fluid Flow ◽  
Pressure Drop ◽  
Heat Transfer Performance ◽  
Flow Boiling ◽  
Transfer Performance ◽  
Flow Conditions ◽  
Pin Fin ◽  
Flow And Heat Transfer

In this paper we reported an advanced structure, the Piranha Pin Fin (PPF), for microchannel flow boiling. Fluid flow and heat transfer performance were evaluated in detail with HFE7000 as working fluid. Surface temperature, pressure drop, heat transfer coefficient and critical heat flux (CHF) were experimentally obtained and discussed. Furthermore, microchannels with different PPF geometrical configurations were investigated. At the same time, tests for different flow conditions were conducted and analyzed. It turned out that microchannel with PPF can realize high-heat flux dissipation with reasonable pressure drop. Both flow conditions and PPF configuration played important roles for both fluid flow and heat transfer performance. This study provided useful reference for further PPF design in microchannel for flow boiling.

Sign in / Sign up

Export Citation Format

Share Document