scholarly journals Effect of Microstructure on the High-Cycle Fatigue Behavior of Ti(43-44)Al4Nb1Mo (TNM) Alloys

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1043
Author(s):  
Bin Tang ◽  
Bin Zhu ◽  
Weiqing Bi ◽  
Yan Liu ◽  
Jinshan Li
Keyword(s):  
Crack Initiation ◽  
High Cycle Fatigue ◽  
Crack Nucleation ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Cycle Fatigue ◽  
Subsurface Crack ◽  
Tial Alloys ◽  
Fracture Morphologies

To investigate the high-cycle fatigue (HCF) behavior of TNM alloys, three different microstructures were designed and obtained by different heat treatments. Staircase tests and fatigue tests in a finite life-region were performed to evaluate the fatigue properties. Then, the fracture surfaces were analyzed to study the fracture behavior of TNM alloys with different microstructures. Results showed that the TNM alloys with duplex microstructure possesses the highest fatigue strength and fatigue life, followed by near lamellar TiAl alloys. HCF failure exhibited cleavage fracture morphologies, and multiple facets were generated in the crack initiation region of different TNM alloys. Two different crack initiation modes, subsurface crack nucleation and surface origin, were observed. Both crack initiation modes appeared in near lamellar alloys, while only subsurface crack initiation were obtained in the duplex (DP) alloy. It contributes to the high scatter of S-N data. The HCF failure of TNM alloys was dominated by crack nucleation rather than crack propagation. These findings could provide guidance for optimizing the microstructure and improving the HCF properties of TiAl alloys.

High Cycle Fatigue Properties of Multi-Directionally Forged Commercial Purity Grade 2 Ti Plate

2018 ◽  
Vol 916 ◽  
pp. 166-169
Author(s):  
Ilhamdi ◽  
Toshifumi Kakiuchi ◽  
Hiromi Miura ◽  
Yoshihiko Uematsu
Keyword(s):  
Crack Initiation ◽  
High Cycle Fatigue ◽  
Pure Titanium ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Commercially Pure Titanium ◽  
Cycle Fatigue ◽  
Subsurface Crack ◽  
Initiation Mechanism ◽  
Fish Eye

Tension-tension fatigue tests were conducted using ultrafine-grained commercially pure Titanium (Ti) plates fabricated by multi-directional forging (MDFing). The MDFed pure Ti plates with the thickness of 1 mm were developed aiming at dental implant application. The fatigue properties of MDFed pure Ti plates were superior to those of the conventional rolled pure Ti plates. The higher fatigue strengths in MDFed plates could be attributed to the much finer grains evolved by MDFing. Fatigue crack initiated from specimen surface, when number of cycles to failure was shorter than 106 cycles. In the high cycle fatigue (HCF) region, however, subsurface crack initiation with typical fish-eye feature was recognized in the MDFed pure Ti plate in spite of the thin thickness. Fractographic analyses revealed that no inclusion existed at the center of fish-eye. The subsurface crack initiation mechanism could be related to the inhomogeneity of microstructure with some coarse grains in the inner part of the plate.

Effect of Plasma Nitriding on Ultra-High Cycle Fatigue Behaviors of Ti-6Al-4V

2011 ◽  
Vol 295-297 ◽  
pp. 2386-2389 ◽  
Author(s):  
Ren Hui Tian ◽  
Qiao Lin Ouyang ◽  
Qing Yuan Wang
Keyword(s):  
High Cycle Fatigue ◽  
Plasma Nitriding ◽  
Fatigue Behavior ◽  
Fatigue Crack Initiation ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Cycle Fatigue ◽  
Ultrasonic Fatigue ◽  
Ultra High Cycle Fatigue ◽  
Stress Ratios

In order to investigate the effect of plasma nitriding treatment on fatigue behavior of titanium alloys, very high cycle fatigue tests were carried out for Ti-6Al-4V alloy using an ultrasonic fatigue machine under load control conditions for stress ratios of R=-1 at frequency of ƒ=20KHz. Experiment results showed that plasma nitriding treatment played the principal role in the internal fatigue crack initiation. More importantly, plasma nitriding treatment had a detrimental effect on fatigue properties of the investigated Ti-6Al-4V alloy, and the fatigue strength of material after plasma nitriding treatment appeared to be significantly reduced about 17% over the untreated material.

Effect of the Rheocasting Process and of the SLS Layer on the Fatigue Behavior of 357 Aluminum Alloy

2014 ◽  
Vol 217-218 ◽  
pp. 227-234 ◽  
Author(s):  
Alain Abou Antoun ◽  
Myriam Brochu ◽  
Heinrich Möller
Keyword(s):  
Aluminum Alloy ◽  
Crack Initiation ◽  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
Fatigue Properties ◽  
Cycle Fatigue ◽  
Initiation Mechanism ◽  
Liquid Segregation ◽  
Surface Liquid ◽  
Effect Of Surface

Two objectives were targeted: 1) compare the high cycle fatigue behavior of rheocast aluminum alloy 357 prepared by the swirl enthalpy equilibration device (SEED) and by the Council for Scientific and Industrial Research (CSIR) process, and 2) study the effect of surface liquid segregation (SLS) on the fatigue behavior of the CSIR material. Rectangular hourglass specimens machined from rheocast plates were tested at four stress amplitudes in axial fatigue with a stress ratio of R = -1 and a frequency of 20 Hz. Results obtained for SLS free specimens show that the SEED and the CSIR processes produce rheocast materials with comparable high cycle fatigue properties, 115 MPa at 107 cycles. In order to study the influence of surface liquid segregation, slightly polished specimens with a remaining SLS of nearly 750 microns thick were also tested. According to the results, the SLS reduces the average fatigue strength by approximately 5% (110 MPa vs. 115 MPa at 107 cycles). For SLS free specimens, the fatigue crack initiated at shrinkage cavities, oxide films or in the alpha globules. On the other hand, for specimens with SLS, no crack initiation in the alpha globules was observed. The main crack initiation mechanism was identified to be a deformation incompatibility between regions characterized by higher silicon content compared to nominal eutectic regions. The originality of the work is provided by the rigorous comparative analysis of the fatigue performance of components produced in two different rheocasting facilities, but tested in a single laboratory. It is also the first fundamental research published on the mechanical effect of surface liquid segregation. It confirms that SLS should be removed in critical areas in order to optimize the fatigue resistance of rheocast components.

Very High Cycle Fatigue Behavior and Thermographic Analysis of High Strength Steel

2010 ◽  
Vol 118-120 ◽  
pp. 948-951
Author(s):  
Chuang Shao ◽  
Claude Bathias ◽  
Danièle Wagner ◽  
Hua Tao
Keyword(s):  
Crack Initiation ◽  
High Strength Steel ◽  
High Cycle Fatigue ◽  
Fatigue Testing ◽  
Fatigue Behavior ◽  
High Strength ◽  
Cycle Fatigue ◽  
Subsurface Crack ◽  
Very High Cycle Fatigue ◽  
Very High

Very high cycle fatigue behavior of high strength steel, were investigated using ultrasonic fatigue testing equipment at 20 kHz up to 109cycles. S-N curves at room temperature with different stress ratio (R=0.01 and R=0.1) was determined. The experimental results show that fatigue strength decrease with increasing number of cycles between 105 and 109. SEM examination of fracture surface reveals that fatigue damage was governed by the formation of cracks, and subsurface crack initiation was in the very long life range. The results shown that the portions of life attributed to subsurface crack initiation between 107 and 109 cycles are 99%.

Effect of corrosion and sandblasting on the high cycle fatigue behavior of reinforcing B500C steel bars

2017 ◽  
Author(s):  
Marina C. Vasco ◽  
Panagiota Polydoropoulou ◽  
Apostolos N. Chamos ◽  
Spiros G. Pantelakis
Keyword(s):  
Mass Loss ◽  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
Salt Spray ◽  
Fatigue Tests ◽  
Tensile Behavior ◽  
Loading Frequency ◽  
Reinforcing Steel ◽  
Cycle Fatigue ◽  
Steel Bars

In a series of applications, steel reinforced concrete structures are subjected to fatigue loads during their service life, what in most cases happens in corrosive environments. Surface treatments have been proved to represent proper processes in order to improve both fatigue and corrosion resistances. In this work, the effect of corrosion and sandblasting on the high cycle fatigue behavior reinforcing steel bars is investigated. The investigated material is the reinforcing steel bar of technical class B500C, of nominal diameter of 12 mm. Steel bars specimens were first exposed to corrosion in alternate salt spray environment for 30 and 60 days and subjected to both tensile and fatigue tests. Then, a series of specimens were subjected to common sandblasting, corroded and mechanically tested. Metallographic investigation and corrosion damage evaluation regarding mass loss and martensitic area reduction were performed. Tensile tests were conducted after each corrosion exposure period prior to the fatigue tests. Fatigue tests were performed at a stress ratio, R, of 0.1 and loading frequency of 20 Hz. All fatigue tests series as well as tensile test were also performed for as received steel bars to obtain the reference behavior. The results have shown that sandblasting hardly affects the tensile behavior of the uncorroded material. The effect of sandblasting on the tensile behavior of pre-corroded specimens seems to be also limited. On the other hand, fatigue results indicate an improved fatigue behavior for the sandblasted material after 60 days of corrosion exposure. Martensitic area reductions, mass loss and depth of the pits were significantly smaller for the case of sandblasted materials, which confirms an increased corrosion resistance.

High-cycle fatigue tests of pretensioned concrete beams

PCI Journal ◽  
2022 ◽  
Vol 67 (1) ◽  
Author(s):  
Jörn Remitz ◽  
Martin Empelmann
Keyword(s):  
Fatigue Life ◽  
High Cycle Fatigue ◽  
Concrete Beams ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
Design Methods ◽  
Test Results ◽  
Cycle Fatigue ◽  
Pretensioned Concrete ◽  
Current Design

Pretensioned concrete beams are widely used as bridge girders for simply supported bridges. Understanding the fatigue behavior of such beams is very important for design and construction to prevent fatigue failure. The fatigue behavior of pretensioned concrete beams is mainly influenced by the fatigue of the prestressing strands. The evaluation of previous test results from the literature indicated a reduced fatigue life in the long-life region compared with current design methods and specifications. Therefore, nine additional high-cycle fatigue tests were conducted on pretensioned concrete beams with strand stress ranges of about 100 MPa (14.5 ksi). The test results confirmed that current design methods and specifications overestimate the fatigue life of embedded strands in pretensioned concrete beams.

Crystal Plasticity Modeling of Laser Peening Effects on Tensile and High Cycle Fatigue Properties of 2024-T351 Aluminum Alloy

2021 ◽  
Vol 143 (7) ◽  
Author(s):  
Maziar Toursangsaraki ◽  
Huamiao Wang ◽  
Yongxiang Hu ◽  
Dhandapanik Karthik
Keyword(s):  
Residual Stresses ◽  
Crystal Plasticity ◽  
High Cycle Fatigue ◽  
Driving Forces ◽  
Crack Nucleation ◽  
Fatigue Properties ◽  
Laser Peening ◽  
Cycle Fatigue ◽  
Fatigue Crack Nucleation ◽  
Near Surface

Abstract This study aims to model the effects of multiple laser peening (LP) on the mechanical properties of AA2024-T351 by including the material microstructure and residual stresses using the crystal plasticity finite element method (CPFEM). In this approach, the LP-induced compressive residual stress distribution is modeled through the insertion of the Eigenstrains as a function of depth, which is calibrated by the X-ray measured residual stresses. The simulated enhancement in the tensile properties after LP, caused by the formation of a near-surface work-hardened layer, fits the experimentally obtained tensile curves. The model calculated fatigue indicator parameters (FIPs) under the following cyclic loading application show a decrease in the near-surface driving forces for the crystal slip deformation after the insertion of the Eigenstrains. This leads to a higher high cycle fatigue (HCF) resistance and the possible transformation of sensitive locations for fatigue failure further to the depth after LP. Experimental observations on the enhancement in the HCF life, along with the relocation of fatigue crack nucleation sites further to the depth, reveal the improvement in the HCF properties due to the LP process and validate the numerical approach.

High Cycle Fatigue Behavior of Recycled Additive Manufactured Electron Beam Melted Titanium Ti6Al4V

2020 ◽  
Author(s):  
Melody Mojib ◽  
Rishi Pahuja ◽  
M. Ramulu ◽  
Dwayne Arola
Keyword(s):  
Electron Beam ◽  
Fatigue Life ◽  
Rough Surface ◽  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
High Strength ◽  
Fatigue Tests ◽  
Cycle Fatigue ◽  
Initiation And Propagation ◽  
Powder Recycling

Abstract Metal Additive Manufacturing (AM) has become a popular method for producing complex and unique geometries, especially gaining traction in the aerospace and medical industries. With the increase in adoption of AM and the high cost of powder, it is critical to understand the effects of powder recycling on part performance to move towards material qualification and certification of affordable printed components. Due to the limitations of the Electron Beam Melting (EBM) process, current as-printed components are susceptible to failure at limits far below wrought metals and further understanding of the material properties and fatigue life is required. In this study, a high strength Titanium alloy, Ti-6Al-4V, is recycled over time and used to print fatigue specimens using the EBM process. Uniaxial High Cycle Fatigue tests have been performed on as-printed and polished cylindrical specimens and the locations of crack initiation and propagation have been determined through the use of a scanning electron microscope. This investigation has shown that the rough surface exterior is far more detrimental to performance life than the powder degradation occurring due to powder reuse. In addition, the effects of the rough surface exterior as a stress concentration is evaluated using the Arola-Ramulu. The following is a preliminary study of the effects powder recycling and surface treatments on EBM Ti-6Al4V fatigue life.

scholarly journals Recent Advances in Very High Cycle Fatigue Behavior of Metals and Alloys—A Review

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1200
Author(s):  
Ashutosh Sharma ◽  
Min Chul Oh ◽  
Byungmin Ahn
Keyword(s):  
Crack Initiation ◽  
High Cycle Fatigue ◽  
Fatigue Testing ◽  
Fatigue Behavior ◽  
Simulation Studies ◽  
Cycle Fatigue ◽  
Future Directions ◽  
Very High Cycle Fatigue ◽  
Ultrasonic Fatigue ◽  
Very High

We reviewed the research and developments in the field of fatigue failure, focusing on very-high cycle fatigue (VHCF) of metals, alloys, and steels. We also discussed ultrasonic fatigue testing, historical relevance, major testing principles, and equipment. The VHCF behavior of Al, Mg, Ni, Ti, and various types of steels were analyzed. Furthermore, we highlighted the major defects, crack initiation sites, fatigue models, and simulation studies to understand the crack development in VHCF regimes. Finally, we reviewed the details regarding various issues and challenges in the field of VHCF for engineering metals and identified future directions in this area.

Sign in / Sign up

Export Citation Format

Share Document