scholarly journals Investigation of the Tribological Characteristics of Aluminum 6061-Reinforced Titanium Carbide Metal Matrix Composites

Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 3039
Author(s):  
G. B. Veeresh Kumar ◽  
R. Pramod ◽  
R. Hari Kiran Reddy ◽  
P. Ramu ◽  
B. Kunaal Kumar ◽  
...  

The current trend in the materials engineering sector is to develop newer materials that can replace the existing materials in various engineering sectors in order to be more and more efficient. Therefore, the present research work is aimed at fabricating and determining the physical, mechanical, and dry sliding wear properties of titanium carbide (TiC)-reinforced aluminum alloy (Al6061) metal matrix composites (MMCs). For the study, the Al6061-TiC microparticle-reinforced composites were fabricated via the liquid metallurgy route through the stir casting method, where the reinforcement of the TiC particles into the Al6061 alloy matrix was added in the range of 0 to 8.0 wt.%, i.e., in the steps of 2.0 wt.%. The synthesis procedure followed the investigation of the various mechanical properties of Al6061-TiC MMCs, such as the density and structure, as well as mechanical and dry wear experimentation. The tests performed on the casted Al6061, as well as its TiC composites, were in harmony with ASTM standards. As per the experimental outcome, it can be confirmed that the increase in the weight percentage of TiC into the Al6061 alloy substantially increases the density, hardness, and tensile strength, at the expense of the percentage of elongation. In addition, the dry wear experiments, performed on a pin-on-disc tribometer, showed that the Al6061-TiC MMCs have superior wear-resistance properties, as compared to those of pure Al6061 alloy. Furthermore, optical micrograph (OM), powdered X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), and scanning electron microscopy (SEM) analyses were employed for the developed Al6061-TiC MMCs before and after the fracture and wear test studies. From the overall analysis of the results, it can be observed that the Al6061-TiC composite material with higher TiC reinforcement displays superior mechanical characteristics.

2019 ◽  
Vol 53 (28-30) ◽  
pp. 4323-4336 ◽  
Author(s):  
Priyaranjan Samal ◽  
Pandu R Vundavilli ◽  
Arabinda Meher ◽  
Manas Mohan Mahapatra

In this paper, aluminium metal matrix composites were synthesized through in situ process in which aluminium alloy 5052 (AA5052) and titanium carbide were used as matrix and reinforcement materials, respectively. The microstructural characterization and formation of stable TiC phases were analyzed with the help of field emission scanning electron microscope, X-ray diffraction analysis, respectively. The 9% TiC-reinforced MMCs had shown a considerable improvement, i.e. 32% increase in hardness, 78% in ultimate tensile strength and 116% increase in yield strength when compared with the base alloy. The tensile fracture of the specimens shows dimples, voids, cracks, and ridges indicating the brittle nature. Further, the dry sliding wear properties of the composites were studied with the help of a pin-on-disc wear testing machine. The composite with 9% TiC exhibited a decrease in volumetric wear loss by 24% when compared with the base alloy at a load of 30 N. With increase in the TiC content and applied load, the COF values decreased linearly for the composites. The 9% TiC-reinforced composites show an abrasive mode of wear mechanism as a result of formation of deep grooves with no plastic deformation. With the improvement obtained in the wear properties, this metal matrix composite can be considered as a replacement for the conventional brake disc material used in the automobile industry.


2021 ◽  
Vol 30 ◽  
pp. 2633366X2092971
Author(s):  
Ying Ba ◽  
Shu Sun

Fiber-reinforced metal matrix composites have mechanical properties highly dependent on directions, possessing high strength and fatigue resistance in fiber longitudinal direction achieved by weak interface bonding. However, the disadvantage of weak interface combination is the reduction of transversal performances. In this article, tensile and fatigue properties of carbon fiber-reinforced 5056 aluminum alloy matrix (Cf/5056Al) composite under the condition of medium-strength interface combination are carried out. The fatigue damage mechanisms of Cf/5056Al composite under tension–tension and tension–compression loads are not the same, but the fatigue life curves are close, which may be the result of the medium-strength interface combination.


Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3110
Author(s):  
Kaveripakkam Suban Ashraff Ali ◽  
Vinayagam Mohanavel ◽  
Subbiah Arungalai Vendan ◽  
Manickam Ravichandran ◽  
Anshul Yadav ◽  
...  

This study focuses on the properties and process parameters dictating behavioural aspects of friction stir welded Aluminium Alloy AA6061 metal matrix composites reinforced with varying percentages of SiC and B4C. The joint properties in terms of mechanical strength, microstructural integrity and quality were examined. The weld reveals grain refinement and uniform distribution of reinforced particles in the joint region leading to improved strength compared to other joints of varying base material compositions. The tensile properties of the friction stir welded Al-MMCs improved after reinforcement with SiC and B4C. The maximum ultimate tensile stress was around 172.8 ± 1.9 MPa for composite with 10% SiC and 3% B4C reinforcement. The percentage elongation decreased as the percentage of SiC decreases and B4C increases. The hardness of the Al-MMCs improved considerably by adding reinforcement and subsequent thermal action during the FSW process, indicating an optimal increase as it eliminates brittleness. It was seen that higher SiC content contributes to higher strength, improved wear properties and hardness. The wear rate was as high as 12 ± 0.9 g/s for 10% SiC reinforcement and 30 N load. The wear rate reduced for lower values of load and increased with B4C reinforcement. The microstructural examination at the joints reveals the flow of plasticized metal from advancing to the retreating side. The formation of onion rings in the weld zone was due to the cylindrical FSW rotating tool material impression during the stirring action. Alterations in chemical properties are negligible, thereby retaining the original characteristics of the materials post welding. No major cracks or pores were observed during the non-destructive testing process that established good quality of the weld. The results are indicated improvement in mechanical and microstructural properties of the weld.


2013 ◽  
Vol 68 ◽  
pp. 186-192 ◽  
Author(s):  
K.S. Alhawari ◽  
M.Z. Omar ◽  
M.J. Ghazali ◽  
M.S. Salleh ◽  
M.N. Mohammed

Wear ◽  
2001 ◽  
Vol 251 (1-12) ◽  
pp. 1408-1413 ◽  
Author(s):  
G. Ranganath ◽  
S.C. Sharma ◽  
M. Krishna

Sign in / Sign up

Export Citation Format

Share Document