scholarly journals Evaluation of Bead Geometry for Aluminum Parts Fabricated Using Additive Manufacturing-Based Wire-Arc Welding

Processes ◽  
2020 ◽  
Vol 8 (10) ◽  
pp. 1211
Author(s):  
Hee-keun Lee ◽  
Jisun Kim ◽  
Changmin Pyo ◽  
Jaewoong Kim
Keyword(s):  
Additive Manufacturing ◽  
Heat Input ◽  
Deposition Efficiency ◽  
Bead Geometry ◽  
Thin Wall ◽  
Cross Sectional ◽  
Voltage Ratio ◽  
Input Range ◽  
The Cross ◽  
Wire Arc Additive Manufacturing

The wire arc additive manufacturing (WAAM) process used to manufacture aluminum parts has a number of variables. This study focuses on the effects of the heat input and the current and voltage ratio on the deposition efficiency. The effects of the heat input and current and voltage ratio (V/A) on the bead geometry were analyzed, depending on the cross-sectional geometry of the deposition layers, for nine different deposition conditions. The deposition efficiency was also analyzed by analyzing the cross-sectional geometry of the thin-wall parts made of aluminum. The heat input range was about 2.7 kJ/cm to 4.5 kJ/cm; the higher the heat input, the higher the deposition efficiency. The maximum deposition efficiency achieved in this study was 76%. The current and voltage ratio was used to quantify the portion of voltage (V) in the total heat input (Q), and the effect on the bead geometry was analyzed. As the portion of voltage in the quasi heat input decreased by about 10%, it was found that the deposition efficiency was decreased by 1% to 3%.

Control of humping phenomenon and analyzing mechanical properties of Al–Si wire-arc additive manufacturing fabricated samples using cold metal transfer process

2021 ◽  
pp. 095440622199840
Author(s):  
Yashwant Koli ◽  
N Yuvaraj ◽  
Aravindan Sivanandam ◽  
Vipin
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Heat Input ◽  
Large Scale ◽  
High Deposition Rate ◽  
Bead Geometry ◽  
Layer By Layer ◽  
Cold Metal Transfer ◽  
Geometrical Shapes ◽  
Wire Arc Additive Manufacturing

Nowadays, rapid prototyping is an emerging trend that is followed by industries and auto sector on a large scale which produces intricate geometrical shapes for industrial applications. The wire arc additive manufacturing (WAAM) technique produces large scale industrial products which having intricate geometrical shapes, which is fabricated by layer by layer metal deposition. In this paper, the CMT technique is used to fabricate single-walled WAAM samples. CMT has a high deposition rate, lower thermal heat input and high cladding efficiency characteristics. Humping is a common defect encountered in the WAAM method which not only deteriorates the bead geometry/weld aesthetics but also limits the positional capability in the process. Humping defect also plays a vital role in the reduction of hardness and tensile strength of the fabricated WAAM sample. The humping defect can be controlled by using low heat input parameters which ultimately improves the mechanical properties of WAAM samples. Two types of path planning directions namely uni-directional and bi-directional are adopted in this paper. Results show that the optimum WAAM sample can be achieved by adopting a bi-directional strategy and operating with lower heat input process parameters. This avoids both material wastage and humping defect of the fabricated samples.

Wire arc additive manufacturing of thin-wall low-carbon steel parts: Microstructure and mechanical properties

2020 ◽  
Vol 34 (22n24) ◽  
pp. 2040154
Author(s):  
Van Thao Le ◽  
Tien Long Banh ◽  
Duc Toan Nguyen ◽  
Van Tao Le
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Carbon Steel ◽  
Heat Input ◽  
Low Carbon Steel ◽  
Production Costs ◽  
High Deposition Rate ◽  
Thin Wall ◽  
Low Carbon ◽  
Wire Arc Additive Manufacturing

Wire arc additive manufacturing (WAAM) has received much attention for manufacturing metal parts with medium and large dimensions because of its high deposition rate and low production costs. In this study, the effects of the heat input on the microstructure formation of thin-wall low-carbon steel parts built by a WAAM process were addressed. The mechanical properties of built materials were also studied. The results indicate that the heat input significantly influences on the shape of built thin walls, but has slight effects on the microstructure evolution of built materials. The WAAM thin-wall low-carbon steel presents suitable microstructures and good tensile strengths (YS: 320 – 362 MPa, UTS: 429 – 479 MPa) that are adequate with industrial applications.

Bead Modelling and Deposition Path Planning in Wire Arc Additive Manufacturing of Three Dimensional Parts

2019 ◽  
Vol 969 ◽  
pp. 582-588 ◽  
Author(s):  
Ashish Kumar ◽  
Kuntal Maji
Keyword(s):  
Additive Manufacturing ◽  
Three Dimensional ◽  
Bead Geometry ◽  
Post Processing ◽  
Bead Width ◽  
Cross Sectional ◽  
Current Electrode ◽  
Wire Material ◽  
Single Bead ◽  
Wire Arc Additive Manufacturing

This paper presents investigations on the manufacturing of three-dimensional functional metallic parts through melting and deposition of stainless steel 430L wire material by a metal inert gas welding technique. Experiments were performed on wire arc additive manufacturing following face centered composite design of experiments considering voltage, current, electrode wire material feed rate and welding speed as inputs for modeling single bead geometry in terms of bead width, height, and cross-sectional area. Response surface models were built using the collected experimental data. Performance of the models in predicting the responses was found satisfactory. Models of single bead geometry were employed to calculate void and post-processing in fabricating three-dimensional parts following raster scanning deposition of multiple layers considering the different degree of overlapping and build directions. The theoretically estimated values of void and post-processing were verified through fabrications of two three-dimensional shapes. It was shown that the void and post-processing could be controlled by suitable selection of process parameters, the degree of overlapping between two beads and build direction.

Wire arc additive manufacturing of Invar parts: bead geometry and melt pool monitoring

Measurement ◽  
2021 ◽  
pp. 110452
Author(s):  
Fernando Veiga ◽  
Alfredo Suarez ◽  
Eider Aldalur ◽  
Teresa Artaza
Keyword(s):  
Additive Manufacturing ◽  
Bead Geometry ◽  
Melt Pool ◽  
Wire Arc Additive Manufacturing

Using Unsupervised Learning for Regulating Deposition Speed During Robotic Wire Arc Additive Manufacturing

2021 ◽  
Author(s):  
Ashish Kulkarni ◽  
Prahar M. Bhatt ◽  
Alec Kanyuck ◽  
Satyandra K. Gupta
Keyword(s):  
Additive Manufacturing ◽  
Unsupervised Learning ◽  
Molten Metal ◽  
Length Variation ◽  
Bead Geometry ◽  
Layer By Layer ◽  
Arc Length ◽  
Regulation Scheme ◽  
Speed Regulation ◽  
Wire Arc Additive Manufacturing

Abstract Robotic Wire Arc Additive Manufacturing (WAAM) is the layer-by-layer deposition of molten metal to build a three-dimensional part. In this process, the fed metal wire is melted using an electric arc as a heat source. The process is sensitive to the arc conditions, such as arc length. While building WAAM parts, the metal beads overlap at corners causing material accumulation. Material accumulation is undesirable as it leads to uneven build height and process failures caused by arc length variation. This paper introduces a deposition speed regulation scheme to avoid the corner accumulation problem and build parts with uniform build height. The regulated speed has a complex relationship with the corner angle, bead geometry, and molten metal dynamics. So we need to train a model that can predict suitable speed regulations for corner angles encountered while building the part. We develop an unsupervised learning technique to characterize the uniformity of the bead profile of a WAAM built layer and check for anomalous bead profiles. We train a model using these results that can predict suitable speed regulation parameters for different corner angles. We test this model by building a WAAM part using our speed regulation scheme and validate if the built part has uniform build height and reduced corner defects.

scholarly journals Effects of Material Properties on Angular Distortion in Wire Arc Additive Manufacturing: Experimental and Computational Analyses

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1399
Author(s):  
Sang-Cheol Park ◽  
Hee-Seon Bang ◽  
Woo-Jae Seong
Keyword(s):  
Additive Manufacturing ◽  
Material Properties ◽  
Heat Input ◽  
Coefficient Of Thermal Expansion ◽  
Angular Distortion ◽  
Substrate Thickness ◽  
Deformation Characteristics ◽  
Temperature Dependent ◽  
Temperature Dependent Properties ◽  
Wire Arc Additive Manufacturing

In wire arc additive manufacturing (AM), as in arc welding, arc heat thermally deforms substrates and articles. For industrial applications, deformation characteristics of various materials must be understood and appropriate materials and methods of reducing deformation must be devised. Therefore, angular distortions of different materials were investigated through bead-on-plate welding and finite element analysis. A model that simplifies temperature-dependent properties was developed to establish relationships between thermomechanical properties and angular distortion. A simplified model of temperature-dependent properties was used, and angular distortion characteristics were extensively investigated for different material properties and heat inputs. Coefficient of thermal expansion, density, and specific heat all notably affected angular distortion depending on heat input conditions. Results showed that during wire arc AM, flatness of both substrates and articles could vary depending on material properties, heat input, substrate thickness, and bead accumulation. Study findings can provide insight into deformation characteristics of new materials and how to mitigate thermal distortions.

Mapping of Bead Geometry in Wire Arc Additive Manufacturing Systems Using Passive Vision

2022 ◽  
Author(s):  
Marcus O. Couto ◽  
Arthur G. Rodrigues ◽  
Fernando Coutinho ◽  
Ramon R. Costa ◽  
Antonio C. Leite ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Manufacturing Systems ◽  
Bead Geometry ◽  
Wire Arc Additive Manufacturing
Sign in / Sign up

Export Citation Format

Share Document