scholarly journals Numerical Investigation of a Novel Heat Pipe Radiant Floor Heating System with Integrated Phase Change Materials

Proceedings ◽  
2020 ◽  
Vol 63 (1) ◽  
pp. 15
Author(s):  
Marius Brănoaea ◽  
Andrei Burlacu ◽  
Vasilică Ciocan ◽  
Marina Verdeș ◽  
Robert Ștefan Vizitiu
Keyword(s):  
Phase Change ◽  
Energy Demand ◽  
Phase Change Materials ◽  
Heat Pipes ◽  
Modern Society ◽  
Heating System ◽  
Cfd Simulations ◽  
Computational Fluid Dynamics Cfd ◽  
Radiant Floor Heating System ◽  
Radiant Floor Heating

The subject of buildings energy efficiency has gained increased interest in modern society. Recently, researchers aiming to reduce the energy demand of buildings have studied the implementation of phase change materials (PCMs) in various building elements. At the same time, researchers studied the implementation of unconventional technologies such as heat pipes (HP) in the buildings’ heating system. This paper combines both of these technologies in order to take advantage of the thermal storage properties of PCMs and overcome their reduced conductivity with heat pipes. Through computational fluid dynamics (CFD) simulations, this paper studies and highlights that with the implementation of a PCM, a reduction of the daily energy demand is achieved through the increase in the discharge phase time.

scholarly journals Defrosting Performance Improvement of Air-Source Heat Pump Combined Refrigerant Direct-Condensation Radiant Floor Heating System with Phase Change Material

Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4594 ◽  
Author(s):  
Chenxiao Zheng ◽  
Shijun You ◽  
Huan Zhang ◽  
Zeqin Liu ◽  
Wandong Zheng ◽  
...  
Keyword(s):  
Phase Change ◽  
Phase Change Material ◽  
Heat Pump ◽  
Heating System ◽  
Air Source Heat Pump ◽  
Composite Phase Change Material ◽  
Radiant Floor Heating System ◽  
Radiant Floor Heating ◽  
Change Material ◽  
Floor Heating

Traditional defrosting methods applied to solve frosting problems of air-source heat pumps operating in cold periods may reduce heat capacity of the system and decrease indoor thermal comfort. In order to improve the performance of air-source heat pump (ASHP) and maintain indoor temperature in defrosting conditions, an air-source heat pump combined with a refrigerant direct-condensation radiant floor heating system with phase change material is proposed and evaluated in this study. Two radiant floor heating terminals with and without composite phase change material modules were compared through experiments. A composite phase change material based on dodecanoic acid-tetradecanol-hexadecanol mixture and expanded graphite was investigated for this application. Experimental results indicate that both heat fluxes of two comparing terminals are higher than 70 W/m2 in heating condition. At the same time, the floor surface temperature, indoor air temperature, and heating capacity of the terminal with composite phase change material modules are higher than those without composite phase change material modules in defrosting condition. This suggests that the proposed system with composite phase change material modules can improve indoor thermal comfort in defrosting condition as well as satisfy the heating requirement in heating condition.

scholarly journals Reducing The Energy Consumption By Using Floor Heating With Phase Change Materials In The Toronto Climate

2021 ◽  
Author(s):  
Lindsay Fialkov
Keyword(s):  
Energy Consumption ◽  
Phase Change ◽  
Phase Change Materials ◽  
Energy Savings ◽  
Cost Savings ◽  
Heating System ◽  
Radiant Floor Heating System ◽  
The Cost ◽  
The Impact ◽  
Floor Heating

This major research project focuses on reducing the energy consumption, by modelling a radiant floor heating system with phase change materials, in the Toronto climate. Computer generated simulations were performed using DesignBuilder software, using an example of a typical condominium in Toronto .Two south facing suites and two north facing suites were investigated. Of those suites, one north facing suite had PCM below the finished floor, as well as one south facing suite. The objective of these simulations was to determine the impact of using PCM in the condo suites. Three different types of PCM were used, in order to determine which type had the biggest energy savings. The PCMs were M91/Q21, M51/Q21 and M27/Q21. The final results showed that the suites with the M27/Q21 PCM had the lowest energy usage. A cost savings comparison was performed based on the rate of energy used and the cost of the energy, provided by the Ontario Energy Board.

Applications of Phase Change Materials for Energy Saving

2012 ◽  
Vol 549 ◽  
pp. 572-575
Author(s):  
Huan Liu ◽  
Yan Rong Tang ◽  
Ya Fei Guo ◽  
Shi Qiang Wang ◽  
Tian Long Deng
Keyword(s):  
Phase Change ◽  
Energy Saving ◽  
Phase Change Material ◽  
Energy Demand ◽  
Phase Change Materials ◽  
Residential Building ◽  
Heating System ◽  
Solar Water Heating ◽  
Solar Water Heating System ◽  
Change Material

Energy demand to ensure a comfortable environment for humans has increased worldwide, especially in the application of phase change material (PCM) for resident living. In this paper, the current applications of PCMs including solar water-heating system, solar cooker and residential building aspects were presented, and the suggestions for future works were also discussed.

scholarly journals Reducing The Energy Consumption By Using Floor Heating With Phase Change Materials In The Toronto Climate

2021 ◽  
Author(s):  
Lindsay Fialkov
Keyword(s):  
Energy Consumption ◽  
Phase Change ◽  
Phase Change Materials ◽  
Energy Savings ◽  
Cost Savings ◽  
Heating System ◽  
Radiant Floor Heating System ◽  
The Cost ◽  
The Impact ◽  
Floor Heating

This major research project focuses on reducing the energy consumption, by modelling a radiant floor heating system with phase change materials, in the Toronto climate. Computer generated simulations were performed using DesignBuilder software, using an example of a typical condominium in Toronto .Two south facing suites and two north facing suites were investigated. Of those suites, one north facing suite had PCM below the finished floor, as well as one south facing suite. The objective of these simulations was to determine the impact of using PCM in the condo suites. Three different types of PCM were used, in order to determine which type had the biggest energy savings. The PCMs were M91/Q21, M51/Q21 and M27/Q21. The final results showed that the suites with the M27/Q21 PCM had the lowest energy usage. A cost savings comparison was performed based on the rate of energy used and the cost of the energy, provided by the Ontario Energy Board.

scholarly journals Energy Saving and Charging Discharging Characteristics of Multiple PCMs Subjected to Internal Air Flow

Fluids ◽  
2021 ◽  
Vol 6 (8) ◽  
pp. 275
Author(s):  
Ahmed J. Hamad
Keyword(s):  
Phase Change ◽  
Energy Saving ◽  
Air Temperature ◽  
Temperature Control ◽  
Phase Change Materials ◽  
Energy Savings ◽  
Heating System ◽  
Air Heating ◽  
Room Model ◽  
Model Temperature

One essential utilization of phase change materials as energy storage materials is energy saving and temperature control in air conditioning and indirect solar air drying systems. This study presents an experimental investigation evaluating the characteristics and energy savings of multiple phase change materials subjected to internal flow in an air heating system during charging and discharging cycles. The experimental tests were conducted using a test rig consisting of two main parts, an air supply duct and a room model equipped with phase change materials (PCMs) placed in rectangular aluminum panels. Analysis of the results was based on three test cases: PCM1 (Paraffin wax) placed in the air duct was used alone in the first case; PCM2 (RT–42) placed in the room model was used alone in the second case; and in the third case, the two PCMs (PCM1 and PCM2) were used at the same time. The results revealed a significant improvement in the energy savings and room model temperature control for the air heating system incorporated with multiple PCMs compared with that of a single PCM. Complete melting during the charging cycle occurred at temperatures in the range of 57–60 °C for PCM1 and 38–43 °C for PCM2, respectively, thereby validating the reported PCMs’ melting–solidification results. Multiple PCMs maintained the room air temperature at the desired range of 35–45.2 °C in the air heating applications by minimizing the air temperature fluctuations. The augmentation in discharging time and improvement in the room model temperature using multiple PCMs were about 28.4% higher than those without the use of PCMs. The total energy saving using two PCMs was higher by about 29.5% and 46.7% compared with the use of PCM1 and PCM2, respectively. It can be concluded that multiple PCMs have revealed higher energy savings and thermal stability for the air heating system considered in the current study.

scholarly journals Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3821
Author(s):  
Kassianne Tofani ◽  
Saeed Tiari
Keyword(s):  
Energy Storage ◽  
Phase Change ◽  
Latent Heat ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Phase Change Materials ◽  
Storage Systems ◽  
Heat Pipes ◽  
Energy Storage Systems ◽  
Thermal Energy Storage Systems

Latent heat thermal energy storage systems (LHTES) are useful for solar energy storage and many other applications, but there is an issue with phase change materials (PCMs) having low thermal conductivity. This can be enhanced with fins, metal foam, heat pipes, multiple PCMs, and nanoparticles (NPs). This paper reviews nano-enhanced PCM (NePCM) alone and with additional enhancements. Low, middle, and high temperature PCM are classified, and the achievements and limitations of works are assessed. The review is categorized based upon enhancements: solely NPs, NPs and fins, NPs and heat pipes, NPs with highly conductive porous materials, NPs and multiple PCMs, and nano-encapsulated PCMs. Both experimental and numerical methods are considered, focusing on how well NPs enhanced the system. Generally, NPs have been proven to enhance PCM, with some types more effective than others. Middle and high temperatures are lacking compared to low temperature, as well as combined enhancement studies. Al2O3, copper, and carbon are some of the most studied NP materials, and paraffin PCM is the most common by far. Some studies found NPs to be insignificant in comparison to other enhancements, but many others found them to be beneficial. This article also suggests future work for NePCM and LHTES systems.

scholarly journals Predicted Medium Vote Thermal Comfort Analysis Applying Energy Simulations with Phase Change Materials for Very Hot-Humid Climates in Social Housing in Ecuador

2021 ◽  
Vol 13 (3) ◽  
pp. 1257
Author(s):  
Luis Godoy-Vaca ◽  
E. Catalina Vallejo-Coral ◽  
Javier Martínez-Gómez ◽  
Marco Orozco ◽  
Geovanna Villacreses
Keyword(s):  
Thermal Comfort ◽  
Phase Change ◽  
Social Housing ◽  
Energy Demand ◽  
Phase Change Materials ◽  
Thermal Sensation ◽  
Electricity Consumption ◽  
Different Types ◽  
Climate Influences ◽  
Energy Simulations

This work aims to estimate the expected hours of Predicted Medium Vote (PMV) thermal comfort in Ecuadorian social housing houses applying energy simulations with Phase Change Materials (PCMs) for very hot-humid climates. First, a novel methodology for characterizing three different types of social housing is presented based on a space-time analysis of the electricity consumption in a residential complex. Next, the increase in energy demand under climate influences is analyzed. Moreover, with the goal of enlarging the time of thermal comfort inside the houses, the most suitable PCM for them is determined. This paper includes both simulations and comparisons of thermal behavior by means of the PMV methodology of four types of PCMs selected. From the performed energy simulations, the results show that changing the deck and using RT25-RT30 in walls, it is possible to increase the duration of thermal comfort in at least one of the three analyzed houses. The applied PCM showed 46% of comfortable hours and a reduction of 937 h in which the thermal sensation varies from “very hot” to “hot”. Additionally, the usage time of air conditioning decreases, assuring the thermal comfort for the inhabitants during a higher number of hours per day.

Sign in / Sign up

Export Citation Format

Share Document