scholarly journals Retrieval of Daytime Total Column Water Vapour from OLCI Measurements over Land Surfaces

2021 ◽  
Vol 13 (5) ◽  
pp. 932
Author(s):  
René Preusker ◽  
Cintia Carbajal Henken ◽  
Jürgen Fischer
Keyword(s):  
Water Vapour ◽  
Near Infrared ◽  
Retrieval Algorithm ◽  
Data Sets ◽  
Data Set ◽  
Uncertainty Estimates ◽  
Resolution Imaging ◽  
Retrieval Errors ◽  
Mean Square Errors ◽  
Total Column

A new retrieval of total column water vapour (TCWV) from daytime measurements over land of the Ocean and Land Colour Instrument (OLCI) on-board the Copernicus Sentinel-3 missions is presented. The Copernicus Sentinel-3 OLCI Water Vapour product (COWa) retrieval algorithm is based on the differential absorption technique, relating TCWV to the radiance ratio of non-absorbing band and nearby water vapour absorbing band and was previously also successfully applied to other passive imagers Medium Resolution Imaging Spectrometer (MERIS) and Moderate Resolution Imaging Spectroradiometer (MODIS). One of the main advantages of the OLCI instrument regarding improved TCWV retrievals lies in the use of more than one absorbing band. Furthermore, the COWa retrieval algorithm is based on the full Optimal Estimation (OE) method, providing pixel-based uncertainty estimates, and transferable to other Near-Infrared (NIR) based TCWV observations. Three independent global TCWV data sets, i.e., Aerosol Robotic Network (AERONET), Atmospheric Radiation Measurement (ARM) and U.S. SuomiNet, and a German Global Navigation Satellite System (GNSS) TCWV data set, all obtained from ground-based observations, serve as reference data sets for the validation. Comparisons show an overall good agreement, with absolute biases between 0.07 and 1.31 kg/m2 and root mean square errors (RMSE) between 1.35 and 3.26 kg/m2. This is a clear improvement in comparison to the operational OLCI TCWV Level 2 product, for which the bias and RMSEs range between 1.10 and 2.55 kg/m2 and 2.08 and 3.70 kg/m2, respectively. A first evaluation of pixel-based uncertainties indicates good estimated uncertainties for lower retrieval errors, while the uncertainties seem to be overestimated for higher retrieval errors.

scholarly journals Total column water vapour measurements from GOME-2 MetOp-A and MetOp-B

2014 ◽  
Vol 7 (3) ◽  
pp. 3021-3073 ◽  
Author(s):  
M. Grossi ◽  
P. Valks ◽  
D. Loyola ◽  
B. Aberle ◽  
S. Slijkhuis ◽  
...  
Keyword(s):  
Water Vapour ◽  
Optical Absorption Spectroscopy ◽  
Retrieval Algorithm ◽  
Data Sets ◽  
Vertical Column ◽  
Data Set ◽  
Vertical Column Density ◽  
Data Processor ◽  
Climate Analysis ◽  
Total Column

Abstract. The knowledge of the total column water vapour (TCWV) global distribution is fundamental for climate analysis and weather monitoring. In this work, we present the retrieval algorithm used to derive the operational TCWV from the GOME-2 sensors and perform an extensive inter-comparison and validation in order to estimate their absolute accuracy and long-term stability. We use the recently reprocessed data sets retrieved by the GOME-2 instruments aboard EUMETSAT's MetOp-A and MetOp-B satellites and generated by DLR in the framework of the O3M-SAF using the GOME Data Processor (GDP) version 4.7. The retrieval algorithm is based on a classical Differential Optical Absorption Spectroscopy (DOAS) method and combines H2O/O2 retrieval for the computation of the trace gas vertical column density. We introduce a further enhancement in the quality of the H2O column by optimizing the cloud screening and developing an empirical correction in order to eliminate the instrument scan angle dependencies. We evaluate the overall consistency between about 8 months measurements from the newer GOME-2 instrument on the MetOp-B platform with the GOME-2/MetOp-A data in the overlap period. Furthermore, we compare GOME-2 results with independent TCWV data from ECMWF and with SSMIS satellite measurements during the full period January 2007–August 2013 and we perform a validation against the combined SSM/I + MERIS satellite data set developed in the framework of the ESA DUE GlobVapour project. We find global mean biases as small as ± 0.03 g cm−2 between GOME-2A and all other data sets. The combined SSM/I-MERIS sample is typically drier than the GOME-2 retrievals (−0.005 g cm−2), while on average GOME-2 data overestimate the SSMIS measurements by only 0.028 g cm−2. However, the size of some of these biases are seasonally dependent. Monthly average differences can be as large as 0.1 g cm−2, based on the analysis against SSMIS measurements, but are not as evident in the validation with the ECMWF and the SSM/I + MERIS data. Studying two exemplary months, we estimate regional differences and identify a very good agreement between GOME-2 total columns and all three independent data sets, especially for land areas, although some discrepancies over ocean and over land areas with high humidity and a relatively large surface albedo are also present.

scholarly journals A 16-year global climate data record of total column water vapour generated from OMI observations in the visible blue spectral range

2021 ◽  
Author(s):  
Christian Borger ◽  
Steffen Beirle ◽  
Thomas Wagner
Keyword(s):  
Water Vapour ◽  
Reference Data ◽  
Retrieval Algorithm ◽  
Time Range ◽  
Data Sets ◽  
Climate Data ◽  
Data Set ◽  
Data Record ◽  
Climate Data Record ◽  
Total Column

Abstract. We present a long-term data set of 1° × 1° monthly mean total column water vapour (TCWV) based on global measurements of the Ozone Monitoring Instrument (OMI) covering the time range from January 2005 to December 2020. In comparison to the retrieval algorithm of Borger et al. (2020) several modifications and filters have been applied accounting for instrumental issues (such as OMI's "row-anomaly") or the inferior quality of solar reference spectra. For instance, to overcome the problems of low quality reference spectra, the daily solar irradiance spectrum is replaced by an annually varying mean Earthshine radiance obtained in December over Antarctica. For the TCWV data set only measurements are taken into account for which the effective cloud fraction < 20 %, the AMF > 0.1, the ground pixel is snow- and ice-free, and the OMI row is not affected by the "row-anomaly" over the complete time range of the data set. The individual TCWV measurements are then gridded to a regular 1° × 1° lattice, from which the monthly means are calculated. In a comprehensive validation study we demonstrate that the OMI TCWV data set is in good agreement to reference data sets of ERA5, RSS SSM/I, and ESA CCI Water Vapour CDR-2: over ocean ordinary least squares (OLS) as well as orthogonal distance regressions (ODR) indicate slopes close to unity with very small offsets and high correlation coefficients of around 0.98. However, over land, distinctive positive deviations are obtained especially within the tropics with relative deviations of approximately +10 % likely caused by uncertainties in the retrieval input data (surface albedo, cloud information) due to frequent cloud contamination in these regions. Nevertheless, a temporal stability analysis proves that the OMI TCWV data set is consistent with the temporal changes of the reference data sets and shows no significant deviation trends. Since the TCWV retrieval can be easily applied to further satellite missions, additional TCWV data sets can be created from past missions such as GOME-1 or SCIAMACHY, which under consideration of systematic differences (e.g. due to different observation times) can be combined with the OMI TCWV data set in order to create a data record that would cover a time span from 1995 to the present. Moreover, the TCWV retrieval will also work for all missions dedicated to NO2 in future such as Sentinel-5 on MetOp-SG. The MPIC OMI total column water vapour (TCWV) climate data record is available at https://doi.org/10.5281/zenodo.5776718 (Borger et al., 2021b).

scholarly journals Total column water vapour measurements from GOME-2 MetOp-A and MetOp-B

2015 ◽  
Vol 8 (3) ◽  
pp. 1111-1133 ◽  
Author(s):  
M. Grossi ◽  
P. Valks ◽  
D. Loyola ◽  
B. Aberle ◽  
S. Slijkhuis ◽  
...  
Keyword(s):  
Water Vapour ◽  
Temporal Stability ◽  
Optical Absorption Spectroscopy ◽  
Retrieval Algorithm ◽  
Data Sets ◽  
Vertical Column ◽  
Data Set ◽  
Vertical Column Density ◽  
Climate Analysis ◽  
Total Column

Abstract. Knowledge of the total column water vapour (TCWV) global distribution is fundamental for climate analysis and weather monitoring. In this work, we present the retrieval algorithm used to derive the operational TCWV from the GOME-2 sensors aboard EUMETSAT's MetOp-A and MetOp-B satellites and perform an extensive inter-comparison in order to evaluate their consistency and temporal stability. For the analysis, the GOME-2 data sets are generated by DLR in the framework of the EUMETSAT O3M-SAF project using the GOME Data Processor (GDP) version 4.7. The retrieval algorithm is based on a classical Differential Optical Absorption Spectroscopy (DOAS) method and combines a H2O and O2 retrieval for the computation of the trace gas vertical column density. We introduce a further enhancement in the quality of the H2O total column by optimizing the cloud screening and developing an empirical correction in order to eliminate the instrument scan angle dependencies. The overall consistency between measurements from the newer GOME-2 instrument on board of the MetOp-B platform and the GOME-2/MetOp-A data is evaluated in the overlap period (December 2012–June 2014). Furthermore, we compare GOME-2 results with independent TCWV data from the ECMWF ERA-Interim reanalysis, with SSMIS satellite measurements during the full period January 2007–June 2014 and against the combined SSM/I + MERIS satellite data set developed in the framework of the ESA DUE GlobVapour project (January 2007–December 2008). Global mean biases as small as ±0.035 g cm−2 are found between GOME-2A and all other data sets. The combined SSM/I-MERIS sample and the ECMWF ERA-Interim data set are typically drier than the GOME-2 retrievals, while on average GOME-2 data overestimate the SSMIS measurements by only 0.006 g cm−2. However, the size of these biases is seasonally dependent. Monthly average differences can be as large as 0.1 g cm−2, based on the analysis against SSMIS measurements, which include only data over ocean. The seasonal behaviour is not as evident when comparing GOME-2 TCWV to the ECMWF ERA-Interim and the SSM/I+MERIS data sets, since the different biases over land and ocean surfaces partly compensate each other. Studying two exemplary months, we estimate regional differences and identify a very good agreement between GOME-2 total columns and all three data sets, especially for land areas, although some discrepancies (bias larger than ±0.5 g cm−2) over ocean and over land areas with high humidity or a relatively large surface albedo are observed.

scholarly journals A global climatology of total columnar water vapour from SSM/I and MERIS

2014 ◽  
Vol 6 (1) ◽  
pp. 221-233 ◽  
Author(s):  
R. Lindstrot ◽  
M. Stengel ◽  
M. Schröder ◽  
J. Fischer ◽  
R. Preusker ◽  
...  
Keyword(s):  
Water Vapour ◽  
Near Infrared ◽  
Radiosonde Data ◽  
Microwave Range ◽  
Data Set ◽  
Uncertainty Estimates ◽  
Merging Process ◽  
Global Coverage ◽  
Land Surfaces ◽  
The Individual

Abstract. A global time series of total columnar water vapour from combined data of the Medium Resolution Imaging Spectrometer (MERIS) onboard ESA's Environmental Satellite (ENVISAT) and the Special Sensor Microwave/Imager (SSM/I) onboard the satellite series of the US Defense Meteorological Satellite Program (DMSP) is presented. The unique data set, generated in the framework of the ESA Data User Element (DUE) GlobVapour project, combines atmospheric water vapour observations over land and ocean, derived from measurements in the near-infrared and the microwave range, respectively. Daily composites and monthly means of total columnar water vapour are available as global maps on rectangular latitude–longitude grids with a spatial resolution of 0.05° × 0.05° over land and 0.5° × 0.5° over ocean for the years 2003 to 2008. The data are stored in NetCDF files and is fully compliant with the NetCDF Climate Forecast convention. Through the combination of high-quality microwave observations and near-infrared observations over ocean and land surfaces, respectively, the data set provides global coverage. The combination of both products is carried out such that the individual properties of the microwave and near-infrared products, in particular their uncertainties, are not modified by the merging process and are therefore well defined. Due to the global coverage and the provided uncertainty estimates this data set is potentially of high value for climate research. The SSM/I-MERIS TCWV data set is freely available via the GlobVapour project web page (www.globvapour.info) with associated doi:10.5676/DFE/WV_COMB/FP. In this paper, the details of the data set generation, i.e. the satellite data used, the retrieval techniques and merging approaches, are presented. The derived level 3 products are compared to global radiosonde data from the GCOS upper air network (GUAN), showing a high agreement with a root-mean-square deviation of roughly 4.4 kg m−2 and a small wet bias well below 1 kg m−2. Furthermore, the data set is shown to be free of seasonal biases. The consistency of the MERIS and SSM/I retrievals is demonstrated by applying the MERIS retrieval to sun glint areas over ocean.

Comparison of hand-held near infrared spectrophotometers for fruit dry matter assessment

2017 ◽  
Vol 25 (4) ◽  
pp. 267-277 ◽  
Author(s):  
Harpreet Kaur ◽  
Rainer Künnemeyer ◽  
Andrew McGlone
Keyword(s):  
Dry Matter ◽  
Near Infrared ◽  
Data Sets ◽  
Prediction Errors ◽  
Data Set ◽  
Instrument Choice ◽  
Spectroscopy Instrumentation ◽  
Portable Instruments ◽  
Mean Square Errors ◽  
Single Instrument

Comparisons are reported for developing predictive models for dry matter across a wide variety of fruits with near infrared spectroscopy instrumentation, using a number of commercially available hand-held portable instruments (NIRVANA by Integrated Spectronics, F-750 by Felix Instruments, H-100C by Sunforest and SCiO by Consumer Physics) and an in-house laboratory based instrument (Benchtop). Three intrinsic (same fruit type) and combined (all fruit types) data sets were created from two separate batches of fruit populations. The first batch (Lot I) consisted of 205 ripe fruits from three different main fruit types (apples, kiwifruit and summerfruit) and 12 distinct fruit sub-categories. The second batch (Lot II) consisted of 91 ripe fruits from two different fruit types (apples and kiwifruit) and seven distinct fruit sub-categories. The laboratory based Benchtop instrument performed the best overall with typically higher prediction r2 values (>0.92). The hand-held instruments delivered moderate to high r2 values between 0.8 and 0.95. Results obtained with the intrinsic data sets revealed typically lower root mean square errors of prediction for apples and kiwifruit (0.32% to 0.73%) and larger prediction errors for summerfruit (0.53% to 0.82%). Some large performance variations between instruments of the same type were observed suggesting caution in evaluating the relative performance of different instrument types or formats on the basis of data generated with just a single instrument and/or data set. However, performance differences between the different hand-held portable instruments, on the same data sets, were often not statistically significant ( p < 0.05). Instrument choice for any particular application will likely come down to matters not considered here, such as, for example, ease and accuracy during in-field operation and overall reliability.

scholarly journals A global climatology of total columnar water vapour from SSM/I and MERIS

2014 ◽  
Vol 7 (1) ◽  
pp. 59-88 ◽  
Author(s):  
R. Lindstrot ◽  
M. Stengel ◽  
M. Schröder ◽  
J. Fischer ◽  
R. Preusker ◽  
...  
Keyword(s):  
Water Vapour ◽  
Near Infrared ◽  
Radiosonde Data ◽  
Microwave Range ◽  
Data Set ◽  
Uncertainty Estimates ◽  
Global Coverage ◽  
Microwave Imager ◽  
Land Surfaces ◽  
The Individual

Abstract. A global time series of total columnar water vapour from combined data of the Medium Resolution Imaging Spectrometer (MERIS) onboard ESA's Environmental Satellite (ENVISAT) and the Special Sensor Microwave/Imager (SSM/I) onboard the satellite series of the US Defense Meteorological Satellite Program (DMSP) is presented. The unique dataset, generated in the framework of the ESA Data User Element (DUE) GlobVapour project, combines atmospheric water vapour observations over land and ocean, derived from measurements in the near infrared and the microwave range, respectively. Daily composites and monthly means of total columnar water vapour are available as global maps on rectangular latitude-longitude grids with a spatial resolution of 0.05° × 0.05° over land and 0.5° × 0.5° over ocean for the years 2003 to 2008. The data is stored in NetCDF files and is fully compliant with the NetCDF Climate Forecast convention. Through the combination of high quality microwave observations and near infrared observations over ocean and land surfaces, respectively, the dataset provides global coverage. The combination of both products is carried out such that the individual properties of the microwave and near-infrared products, in particular their uncertainties, are not changed and therefore well defined. Due to the global coverage and the provided uncertainty estimates this data set is potentially of high value for climate research. The SSM/I-MERIS TCWV data set is freely available via the GlobVapour project web page with associated doi (doi:10.5676/DFE/WV_COMB/FP). In this paper, the details of the dataset generation, i.e. the satellite data used, the retrieval techniques and merging approaches are presented. The derived level 3 products are compared to global radiosonde data from the GCOS upper air network (GUAN), showing a high agreement with a root mean square deviation of roughly 4.4 kg m−2 and a small wet bias well below 1 kg m−2. Furthermore, the data set is shown to be free of seasonal biases. The consistency of the MERIS and SSM/I retrievals is demonstrated by applying the MERIS retrieval to sun glint areas over ocean.

scholarly journals Consistent satellite XCO<sub>2</sub> retrievals from SCIAMACHY and GOSAT using the BESD algorithm

2015 ◽  
Vol 8 (2) ◽  
pp. 1787-1832 ◽  
Author(s):  
J. Heymann ◽  
M. Reuter ◽  
M. Hilker ◽  
M. Buchwitz ◽  
O. Schneising ◽  
...  
Keyword(s):  
Carbon Cycle ◽  
Detailed Comparison ◽  
Mean Difference ◽  
Total Carbon ◽  
Retrieval Algorithm ◽  
Data Sets ◽  
Data Set ◽  
Time Period ◽  
Comparison Results ◽  
The Future

Abstract. Consistent and accurate long-term data sets of global atmospheric concentrations of carbon dioxide (CO2) are required for carbon cycle and climate related research. However, global data sets based on satellite observations may suffer from inconsistencies originating from the use of products derived from different satellites as needed to cover a long enough time period. One reason for inconsistencies can be the use of different retrieval algorithms. We address this potential issue by applying the same algorithm, the Bremen Optimal Estimation DOAS (BESD) algorithm, to different satellite instruments, SCIAMACHY onboard ENVISAT (March 2002–April 2012) and TANSO-FTS onboard GOSAT (launched in January 2009), to retrieve XCO2, the column-averaged dry-air mole fraction of CO2. BESD has been initially developed for SCIAMACHY XCO2 retrievals. Here, we present the first detailed assessment of the new GOSAT BESD XCO2 product. GOSAT BESD XCO2 is a product generated and delivered to the MACC project for assimilation into ECMWF's Integrated Forecasting System (IFS). We describe the modifications of the BESD algorithm needed in order to retrieve XCO2 from GOSAT and present detailed comparisons with ground-based observations of XCO2 from the Total Carbon Column Observing Network (TCCON). We discuss detailed comparison results between all three XCO2 data sets (SCIAMACHY, GOSAT and TCCON). The comparison results demonstrate the good consistency between the SCIAMACHY and the GOSAT XCO2. For example, we found a mean difference for daily averages of −0.60 ± 1.56 ppm (mean difference ± standard deviation) for GOSAT-SCIAMACHY (linear correlation coefficient r = 0.82), −0.34 ± 1.37 ppm (r = 0.86) for GOSAT-TCCON and 0.10 ± 1.79 ppm (r = 0.75) for SCIAMACHY-TCCON. The remaining differences between GOSAT and SCIAMACHY are likely due to non-perfect collocation (±2 h, 10° × 10° around TCCON sites), i.e., the observed air masses are not exactly identical, but likely also due to a still non-perfect BESD retrieval algorithm, which will be continuously improved in the future. Our overarching goal is to generate a satellite-derived XCO2 data set appropriate for climate and carbon cycle research covering the longest possible time period. We therefore also plan to extend the existing SCIAMACHY and GOSAT data set discussed here by using also data from other missions (e.g., OCO-2, GOSAT-2, CarbonSat) in the future.

scholarly journals Methods for estimating uncertainty in factor analytic solutions

2014 ◽  
Vol 7 (3) ◽  
pp. 781-797 ◽  
Author(s):  
P. Paatero ◽  
S. Eberly ◽  
S. G. Brown ◽  
G. A. Norris
Keyword(s):  
Environmental Protection Agency ◽  
Synthetic Data ◽  
Analytic Solutions ◽  
Data Sets ◽  
Random Errors ◽  
Data Set ◽  
Factor Analytic ◽  
Uncertainty Estimates ◽  
Multilinear Engine ◽  
Analytic Models

Abstract. The EPA PMF (Environmental Protection Agency positive matrix factorization) version 5.0 and the underlying multilinear engine-executable ME-2 contain three methods for estimating uncertainty in factor analytic models: classical bootstrap (BS), displacement of factor elements (DISP), and bootstrap enhanced by displacement of factor elements (BS-DISP). The goal of these methods is to capture the uncertainty of PMF analyses due to random errors and rotational ambiguity. It is shown that the three methods complement each other: depending on characteristics of the data set, one method may provide better results than the other two. Results are presented using synthetic data sets, including interpretation of diagnostics, and recommendations are given for parameters to report when documenting uncertainty estimates from EPA PMF or ME-2 applications.

scholarly journals 3-D visualisation of palaeoseismic trench stratigraphy and trench logging using terrestrial remote sensing and GPR – a multiparametric interpretation

Solid Earth ◽  
2016 ◽  
Vol 7 (2) ◽  
pp. 323-340 ◽  
Author(s):  
Sascha Schneiderwind ◽  
Jack Mason ◽  
Thomas Wiatr ◽  
Ioannis Papanikolaou ◽  
Klaus Reicherter
Keyword(s):  
Seismic Hazard ◽  
Near Infrared ◽  
Normal Faults ◽  
Data Sets ◽  
Data Set ◽  
Backscatter Signal ◽  
Multispectral Data ◽  
Sedimentary Architecture ◽  
Hazard Assessments ◽  
Multispectral Analysis

Abstract. Two normal faults on the island of Crete and mainland Greece were studied to test an innovative workflow with the goal of obtaining a more objective palaeoseismic trench log, and a 3-D view of the sedimentary architecture within the trench walls. Sedimentary feature geometries in palaeoseismic trenches are related to palaeoearthquake magnitudes which are used in seismic hazard assessments. If the geometry of these sedimentary features can be more representatively measured, seismic hazard assessments can be improved. In this study more representative measurements of sedimentary features are achieved by combining classical palaeoseismic trenching techniques with multispectral approaches. A conventional trench log was firstly compared to results of ISO (iterative self-organising) cluster analysis of a true colour photomosaic representing the spectrum of visible light. Photomosaic acquisition disadvantages (e.g. illumination) were addressed by complementing the data set with active near-infrared backscatter signal image from t-LiDAR measurements. The multispectral analysis shows that distinct layers can be identified and it compares well with the conventional trench log. According to this, a distinction of adjacent stratigraphic units was enabled by their particular multispectral composition signature. Based on the trench log, a 3-D interpretation of attached 2-D ground-penetrating radar (GPR) profiles collected on the vertical trench wall was then possible. This is highly beneficial for measuring representative layer thicknesses, displacements, and geometries at depth within the trench wall. Thus, misinterpretation due to cutting effects is minimised. This manuscript combines multiparametric approaches and shows (i) how a 3-D visualisation of palaeoseismic trench stratigraphy and logging can be accomplished by combining t-LiDAR and GPR techniques, and (ii) how a multispectral digital analysis can offer additional advantages to interpret palaeoseismic and stratigraphic data. The multispectral data sets are stored allowing unbiased input for future (re)investigations.

scholarly journals Orbiting Carbon Observatory-2 (OCO-2) cloud screening algorithms; validation against collocated MODIS and CALIOP data

2015 ◽  
Vol 8 (12) ◽  
pp. 12663-12707 ◽  
Author(s):  
T. E. Taylor ◽  
C. W. O'Dell ◽  
C. Frankenberg ◽  
P. Partain ◽  
H. Q. Cronk ◽  
...  
Keyword(s):  
Surface Pressure ◽  
Near Infrared ◽  
Optical Absorption Spectroscopy ◽  
Retrieval Algorithm ◽  
Orthogonal Polarization ◽  
Screening Methods ◽  
Data Set ◽  
Atmospheric Scattering ◽  
Carbon Dioxide Co2 ◽  
Cloud Screening

Abstract. The objective of the National Aeronautics and Space Administration's (NASA) Orbiting Carbon Observatory-2 (OCO-2) mission is to retrieve the column-averaged carbon dioxide (CO2) dry air mole fraction (XCO2) from satellite measurements of reflected sunlight in the near-infrared. These estimates can be biased by clouds and aerosols within the instrument's field of view (FOV). Screening of the most contaminated soundings minimizes unnecessary calls to the computationally expensive Level 2 (L2) XCO2 retrieval algorithm. Hence, robust cloud screening methods have been an important focus of the OCO-2 algorithm development team. Two distinct, computationally inexpensive cloud screening algorithms have been developed for this application. The A-Band Preprocessor (ABP) retrieves the surface pressure using measurements in the 0.76 μm O2 A-band, neglecting scattering by clouds and aerosols, which introduce photon path-length (PPL) differences that can cause large deviations between the expected and retrieved surface pressure. The Iterative Maximum A-Posteriori (IMAP) Differential Optical Absorption Spectroscopy (DOAS) Preprocessor (IDP) retrieves independent estimates of the CO2 and H2O column abundances using observations taken at 1.61 μm (weak CO2 band) and 2.06 μm (strong CO2 band), while neglecting atmospheric scattering. The CO2 and H2O column abundances retrieved in these two spectral regions differ significantly in the presence of cloud and scattering aerosols. The combination of these two algorithms, which key off of different features in the spectra, provides the basis for cloud screening of the OCO-2 data set. To validate the OCO-2 cloud screening approach, collocated measurements from NASA's Moderate Resolution Imaging Spectrometer (MODIS), aboard the Aqua platform, were compared to results from the two OCO-2 cloud screening algorithms. With tuning to allow throughputs of &amp;simeq; 30 %, agreement between the OCO-2 and MODIS cloud screening methods is found to be &amp;simeq; 85 % over four 16-day orbit repeat cycles in both the winter (December) and spring (April–May) for OCO-2 nadir-land, glint-land and glint-water observations. No major, systematic, spatial or temporal dependencies were found, although slight differences in the seasonal data sets do exist and validation is more problematic with increasing solar zenith angle and when surfaces are covered in snow and ice and have complex topography. To further analyze the performance of the cloud screening algorithms, an initial comparison of OCO-2 observations was made to collocated measurements from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) aboard the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO). These comparisons highlight the strength of the OCO-2 cloud screening algorithms in identifying high, thin clouds but suggest some difficulty in identifying some clouds near the surface, even when the optical thicknesses are greater than 1.

Sign in / Sign up

Export Citation Format

Share Document