scholarly journals Performance Improvement of Thermoelectric Air Cooler System by Using Variable-Pulse Current for Building Applications

2021 ◽  
Vol 13 (17) ◽  
pp. 9682
Author(s):  
Kashif Irshad
Keyword(s):  
Steady State ◽  
Current Pulse ◽  
Thermoelectric Module ◽  
Input Current ◽  
Maximum Temperature ◽  
Cooling Load ◽  
Cold Side ◽  
Pulse Operation ◽  
Temperature Reduction ◽  
Steady State Operation

The thermoelectric air conditioning system (TE-AC) is a small, noiseless alternative to standard vapor compression refrigeration (VCR) systems. The cooling characteristics of a TE-AC system operating under two conditions, i.e., steady current and current pulses, are investigated in this study. This system consists of three thermoelectric modules, a heat sink, and an air circulation fan. The result shows that maximum temperature reduction in cooling side of TE-AC system was achieved at 6 A input current under steady state operation. The optimum performance of the TE-AC system under steady state operation depends upon the combined effect of the cooling load, Joule, Fourier, and Peltier heat. In TE-AC pulse operation, both current width and cooling load applied on the cold side of the thermoelectric module (TEMs) play an important role in achieving optimum cooling performance of the system. When normal input current operation (i.e., no current pulse) was compared to pulse-operated TE-AC system operation, it was found that pulse operation provides an additional average temperature reduction of 3–4 °C on the cold side of TEMs. Although on the hot side, it maintains a temperature in the range of 18 °C to 24 °C to reduce overshoot heat flux. The duration of operation is also important in determining pulse width and pulse amplitude. Minimum and overshoot peak temperature rises during each cycle for longer run operation. In the TE-AC system, the accumulated Joule heat during a current pulse frequently causes a temperature overshoot, which lasts much longer. As a result, the next current pulse was not released until the temperature of TE was restored to its initial value.

scholarly journals Steady state operation simulation of the Francis-99 turbine by means of advanced turbulence models

2017 ◽  
Vol 782 ◽  
pp. 012006
Author(s):  
A Gavrilov ◽  
A Dekterev ◽  
A Minakov ◽  
D Platonov ◽  
A Sentyabov
Keyword(s):  
Steady State ◽  
Turbulence Models ◽  
Steady State Operation

Fluid turbulence simulations of divertor heat load for ITER hybrid scenario using BOUT++

2021 ◽  
Author(s):  
Xueyun Wang ◽  
Xueqiao Xu ◽  
Philip B Snyder ◽  
Zeyu Li
Keyword(s):  
Heat Flux ◽  
Steady State ◽  
Energy Loss ◽  
Heat Load ◽  
Type I ◽  
Fluid Turbulence ◽  
Drift Model ◽  
Steady State Operation ◽  
Different Types ◽  
The One

Abstract The BOUT++ six-field turbulence code is used to simulate the ITER 11.5MA hybrid scenario and a brief comparison is made among ITER baseline, hybrid and steady-state operation (SSO) scenarios. Peeling-ballooning instabilities with different toroidal mode numbers dominate in different scenarios and consequently yield different types of ELMs. The energy loss fractions (ΔWped/Wped) caused by unmitigated ELMs in the baseline and hybrid scenarios are large (~2%) while the one in the SSO scenario is dramatically smaller (~1%), which are consistent with the features of type-I ELMs and grassy ELMs respectively. The intra ELM divertor heat flux width in the three scenarios given by the simulations is larger than the estimations for inter ELM phase based on Goldston’s heuristic drift model. The toroidal gap edge melting limit of tungsten monoblocks of divertor targets imposes constraints on ELM energy loss, giving that the ELM energy loss fraction should be smaller than 0.4%, 1.0%, and 1.2% for ITER baseline, hybrid and SSO scenarios, correspondingly. The simulation shows that only the SSO scenario with grassy ELMs may satisfy the constraint.

Sign in / Sign up

Export Citation Format

Share Document